Modify

Opened 7 years ago

Closed 6 years ago

Last modified 6 years ago

#9702 closed defect (fixed)

WP543 latest board ethernet not getting detected

Reported by: wifi802.11abgn@… Owned by: juhosg
Priority: highest Milestone: Backfire 10.03.1
Component: kernel Version: Backfire 10.03.1 RC4
Keywords: Cc: juhosg@…

Description

Hi ,

I have a latest COMPEX WP543 boards, when i try to flash the backfire 10.03.1-rc4 file openwrt-ar71xx-wp543-jffs2-8M-factory.img , while booting the ethernet interface is not getting detected. I have attached the dmesg log file.

I found while booting its throws the error message as "eth0: no PHY found with phy_mask=00000008"

Any one faced the problem ? any fix is available for this ethernet detection ?

Thanks in advance

Attachments (1)

dmeg.txt (4.3 KB) - added by wifi802.11abgn@… 7 years ago.
dmeg_log_file

Download all attachments as: .zip

Change History (8)

Changed 7 years ago by wifi802.11abgn@…

dmeg_log_file

comment:1 Changed 7 years ago by gokul.beece@…

--- linux/kernels/linux-2.6.32.16/arch/mips/ar71xx/mach-wp543.c
+++ linux/kernels/linux-2.6.32.16/arch/mips/ar71xx/mach-wp543.c

ar71xx_add_device_m25p80(NULL);


  • ar71xx_add_device_mdio(0xfffffff7);

+ ar71xx_add_device_mdio(0xfffffff0);

ar71xx_eth0_data.phy_if_mode = PHY_INTERFACE_MODE_MII;

  • ar71xx_eth0_data.phy_mask = 0x08;

+ ar71xx_eth0_data.phy_mask = 0x0f;

ar71xx_eth0_data.reset_bit = RESET_MODULE_GE0_MAC |

RESET_MODULE_GE0_PHY;

adding this patch , the interface got detected fine.

comment:2 Changed 7 years ago by jow

  • Owner changed from developers to juhosg
  • Status changed from new to assigned

comment:3 Changed 6 years ago by g.herrera@…

Same thing happening to me. The ethernet device doesnt get detected. If I flash the same firmware to a WPJ543, the ethernet board on the former board works fine.

Here are the boot messages of the two boards

*
WPJ543 (working ethernet interface)
*

MyLoader version 2.60.1214                                                      
System memory: 32MB                                                             
                                                                                
Probing for Serial flash ...                                                    
Found SPI serial flash                                                          
Flash memory: 4MB                                                               
                                                                                
USB:   scanning bus for devices... 1 USB Device(s) found                        
       scanning bus for storage devices... 0 Storage Device(s) found            
No supported USB Flash disk found                                               
                                                                                
MDIO PHY scan:                                                                  
PHY ID [3] = 004d-d021                                                          
Link Up, Full Duplex, 100 Mbps                                                  
                                                                                
Load Firmware                                                                   
                                                                                
Waiting 5 seconds for firmware upload ...                                       
Mini TFTP Server 1.0 (IP : 192.168.168.1)                                       
Usage (Windows 2000/XP) :                                                       
  tftp -i 192.168.168.1 put <filename>                                          
                                                                                
Loading Firmware ......................................... Done.                
                                                                                
Linux version 2.6.32.27 (german@compaq) (gcc version 4.3.3 (GCC) ) #1 Wed Nov 91
bootconsole [early0] enabled                                                    
CPU revision is: 00019374 (MIPS 24Kc)                                           
Atheros AR7130 rev 2, CPU:300.000 MHz, AHB:150.000 MHz, DDR:300.000 MHz         
Determined physical RAM map:                                                    
 memory: 02000000 @ 00000000 (usable)                                           
Initrd not found or empty - disabling initrd                                    
Zone PFN ranges:                                                                
  Normal   0x00000000 -> 0x00002000                                             
Movable zone start PFN for each node                                            
early_node_map[1] active PFN ranges                                             
    0: 0x00000000 -> 0x00002000                                                 
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 8128       
Kernel command line: rootfstype=squashfs,yaffs,jffs2 noinitrd console=ttyS0,1150
PID hash table entries: 128 (order: -3, 512 bytes)                              
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)                   
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)                     
Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.                 
Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes          
Writing ErrCtl register=00000002                                                
Readback ErrCtl register=00000002                                               
Memory: 29384k/32768k available (2045k kernel code, 3384k reserved, 405k data, )
SLUB: Genslabs=7, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1          
Hierarchical RCU implementation.                                                
NR_IRQS:56                                                                      
Calibrating delay loop... 199.88 BogoMIPS (lpj=999424)                          
Mount-cache hash table entries: 512                                             
NET: Registered protocol family 16                                              
MIPS: machine is Compex WP543                                                   
registering PCI controller with io_map_base unset                               
bio: create slab <bio-0> at 0                                                   
pci 0000:00:00.0: PME# supported from D0 D1 D2 D3hot                            
pci 0000:00:00.0: PME# disabled                                                 
pci 0000:00:11.0: PME# supported from D0 D3hot                                  
pci 0000:00:11.0: PME# disabled                                                 
PCI: mapping irq 48 to pin1@0000:00:11.0                                        
Switching to clocksource MIPS                                                   
NET: Registered protocol family 2                                               
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)                  
TCP established hash table entries: 1024 (order: 1, 8192 bytes)                 
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)                        
TCP: Hash tables configured (established 1024 bind 1024)                        
TCP reno registered                                                             
NET: Registered protocol family 1                                               
squashfs: version 4.0 (2009/01/31) Phillip Lougher                              
Registering mini_fo version $Id$                                                
JFFS2 version 2.2. (NAND) (SUMMARY)  �© 2001-2006 Red Hat, Inc.                 
yaffs Nov  9 2011 15:28:22 Installing.                                          
msgmni has been set to 57                                                       
io scheduler noop registered                                                    
io scheduler deadline registered (default)                                      
Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled                        
serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A                   
console [ttyS0] enabled, bootconsole disabled                                   
console [ttyS0] enabled, bootconsole disabled                                   
Atheros AR71xx SPI Controller driver version 0.2.4                              
m25p80 spi0.0: m25p32 (4096 Kbytes)                                             
4 MyLoader partitions found on MTD device spi0.0                                
Creating 4 MTD partitions on "spi0.0":                                          
0x000000000000-0x000000020000 : "myloader"                                      
0x000000020000-0x000000030000 : "partition_table"                               
0x000000030000-0x000000110000 : "kernel"                                        
0x000000110000-0x000000400000 : "rootfs"                                        
mtd: partition "rootfs" set to be root filesystem                               
mtd: partition "rootfs_data" created automatically, ofs=290000, len=170000      
0x000000290000-0x000000400000 : "rootfs_data"                                   
ag71xx_mdio: probed                                                             
eth0: Atheros AG71xx at 0xb9000000, irq 4                                       
Atheros AR71xx hardware watchdog driver version 0.1.0                           
TCP westwood registered                                                         
NET: Registered protocol family 17                                              
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>                   
All bugs added by David S. Miller <davem@redhat.com>                            
VFS: Mounted root (squashfs filesystem) readonly on device 31:3.                
Freeing unused kernel memory: 148k freed                                        
Please be patient, while OpenWrt loads ...                                      
input: gpio-buttons as /devices/platform/gpio-buttons/input/input0              
Button Hotplug driver version 0.3.1                                             
- preinit -                                                                     
Registered led device: wp543:green:led1                                         
Registered led device: wp543:green:led2                                         
Registered led device: wp543:green:wlan                                         
Registered led device: wp543:green:conn                                         
Registered led device: wp543:green:diag                                         
Press the [f] key and hit [enter] to enter failsafe mode                        
eth0: link up (100Mbps/Full duplex)                                             
- regular preinit -                                                             
switching to jffs2                                                              
mini_fo: using base directory: /                                                
mini_fo: using storage directory: /overlay                                      
- init -                                                                        
eth0: link down                                                                 
                                                                                
Please press Enter to activate this console. device eth0 entered promiscuous moe
eth0: link up (100Mbps/Full duplex)                                             
br-lan: port 1(eth0) entering forwarding state                                  
Compat-wireless backport release: compat-wireless-2011-08-25                    
Backport based on wireless-testing.git master-2011-09-14                        
cfg80211: Calling CRDA to update world regulatory domain                        
usbcore: registered new interface driver usbfs                                  
usbcore: registered new interface driver hub                                    
usbcore: registered new device driver usb                                       
cfg80211: World regulatory domain updated:                                      
cfg80211:     (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) 
cfg80211:     (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)      
cfg80211:     (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)      
cfg80211:     (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)      
cfg80211:     (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)      
cfg80211:     (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)      
PCI: Enabling device 0000:00:11.0 (0000 -> 0002)                                
Registered led device: ath9k-phy0                                               
ieee80211 phy0: Atheros AR9280 Rev:2 mem=0xb0000000, irq=48                     
cfg80211: Calling CRDA for country: US                                          
cfg80211: Regulatory domain changed to country: US                              
cfg80211:     (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) 
cfg80211:     (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)      
cfg80211:     (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)      
cfg80211:     (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)      
cfg80211:     (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)      
cfg80211:     (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)      
cfg80211:     (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)      
PPP generic driver version 2.4.2                                                
ip_tables: (C) 2000-2006 Netfilter Core Team                                    
NET: Registered protocol family 24                                              
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver                      
ar71xx-ehci ar71xx-ehci: Atheros AR71xx built-in EHCI controller                
ar71xx-ehci ar71xx-ehci: new USB bus registered, assigned bus number 1          
ar71xx-ehci ar71xx-ehci: irq 3, io mem 0x1b000000                               
ar71xx-ehci ar71xx-ehci: USB 2.0 started, EHCI 1.00                             
usb usb1: configuration #1 chosen from 1 choice                                 
hub 1-0:1.0: USB hub found                                                      
hub 1-0:1.0: 2 ports detected                                                   
nf_conntrack version 0.5.0 (461 buckets, 1844 max)                              
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver                          
ar71xx-ohci ar71xx-ohci: Atheros AR71xx built-in OHCI controller                
ar71xx-ohci ar71xx-ohci: new USB bus registered, assigned bus number 2          
ar71xx-ohci ar71xx-ohci: irq 14, io mem 0x1c000000                              
usb usb2: configuration #1 chosen from 1 choice                                 
hub 2-0:1.0: USB hub found                                                      
hub 2-0:1.0: 2 ports detected                                                   
                                                                                
                                                                                
                                                                                
BusyBox v1.15.3 (2011-11-09 15:02:37 ART) built-in shell (ash)                  
Enter 'help' for a list of built-in commands.                                   
                                                                                
  _______                     ________        __                                
 |       |.-----.-----.-----.|  |  |  |.----.|  |_                              
 |   -   ||  _  |  -__|     ||  |  |  ||   _||   _|                             
 |_______||   __|_____|__|__||________||__|  |____|                             
          |__| W I R E L E S S   F R E E D O M                                  
 Backfire (10.03.1-RC6, r28875) --------------------                            
  * 1/3 shot Kahlua    In a shot glass, layer Kahlua                            
  * 1/3 shot Bailey's  on the bottom, then Bailey's,                            
  * 1/3 shot Vodka     then Vodka.                                              
 ---------------------------------------------------                            
root@OpenWrt:/# 

*
WP543 (ethernet not working) *
*

MyLoader version 2.60.1214                                                      
System memory: 32MB                                                             
                                                                                
Probing for Serial flash ...                                                    
Found SPI serial flash                                                          
Flash memory: 8MB                                                               
                                                                                
USB:   scanning bus for devices... 1 USB Device(s) found                        
       scanning bus for storage devices... 0 Storage Device(s) found            
No supported USB Flash disk found                                               
                                                                                
MDIO PHY scan:                                                                  
PHY ID [0] = 004d-d021                                                          
Link Up, Full Duplex, 100 Mbps                                                  
                                                                                
Load Firmware                                                                   
                                                                                
Waiting 5 seconds for firmware upload ...                                       
Mini TFTP Server 1.0 (IP : 192.168.168.1)                                       
Usage (Windows 2000/XP) :                                                       
  tftp -i 192.168.168.1 put <filename>                                          
                                                                                
Loading Firmware ......................................... Done.                
                                                                                
Linux version 2.6.32.27 (german@compaq) (gcc version 4.3.3 (GCC) ) #1 Wed Nov 91
bootconsole [early0] enabled                                                    
CPU revision is: 00019374 (MIPS 24Kc)                                           
Atheros AR7161 rev 2, CPU:600.000 MHz, AHB:150.000 MHz, DDR:400.000 MHz         
Determined physical RAM map:                                                    
 memory: 02000000 @ 00000000 (usable)                                           
Initrd not found or empty - disabling initrd                                    
Zone PFN ranges:                                                                
  Normal   0x00000000 -> 0x00002000                                             
Movable zone start PFN for each node                                            
early_node_map[1] active PFN ranges                                             
    0: 0x00000000 -> 0x00002000                                                 
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 8128       
Kernel command line: rootfstype=squashfs,yaffs,jffs2 noinitrd console=ttyS0,115d
PID hash table entries: 128 (order: -3, 512 bytes)                              
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)                   
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)                     
Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.                 
Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes          
Writing ErrCtl register=00003012                                                
Readback ErrCtl register=00003012                                               
Memory: 29384k/32768k available (2045k kernel code, 3384k reserved, 405k data, )
SLUB: Genslabs=7, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1          
Hierarchical RCU implementation.                                                
NR_IRQS:56                                                                      
Calibrating delay loop... 399.76 BogoMIPS (lpj=1998848)                         
Mount-cache hash table entries: 512                                             
NET: Registered protocol family 16                                              
MIPS: machine is Compex WP543                                                   
registering PCI controller with io_map_base unset                               
bio: create slab <bio-0> at 0                                                   
pci 0000:00:00.0: PME# supported from D0 D1 D2 D3hot                            
pci 0000:00:00.0: PME# disabled                                                 
pci 0000:00:12.0: PME# supported from D0 D3hot                                  
pci 0000:00:12.0: PME# disabled                                                 
PCI: mapping irq 49 to pin1@0000:00:12.0                                        
Switching to clocksource MIPS                                                   
NET: Registered protocol family 2                                               
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)                  
TCP established hash table entries: 1024 (order: 1, 8192 bytes)                 
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)                        
TCP: Hash tables configured (established 1024 bind 1024)                        
TCP reno registered                                                             
NET: Registered protocol family 1                                               
squashfs: version 4.0 (2009/01/31) Phillip Lougher                              
Registering mini_fo version $Id$                                                
JFFS2 version 2.2. (NAND) (SUMMARY)  �© 2001-2006 Red Hat, Inc.                 
yaffs Nov  9 2011 15:28:22 Installing.                                          
msgmni has been set to 57                                                       
io scheduler noop registered                                                    
io scheduler deadline registered (default)                                      
Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled                        
serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A                   
console [ttyS0] enabled, bootconsole disabled                                   
console [ttyS0] enabled, bootconsole disabled                                   
Atheros AR71xx SPI Controller driver version 0.2.4                              
m25p80 spi0.0: mx25l6405d (8192 Kbytes)                                         
4 MyLoader partitions found on MTD device spi0.0                                
Creating 4 MTD partitions on "spi0.0":                                          
0x000000000000-0x000000020000 : "myloader"                                      
0x000000020000-0x000000030000 : "partition_table"                               
0x000000030000-0x000000110000 : "kernel"                                        
0x000000110000-0x000000400000 : "rootfs"                                        
mtd: partition "rootfs" set to be root filesystem                               
mtd: partition "rootfs_data" created automatically, ofs=290000, len=170000      
0x000000290000-0x000000400000 : "rootfs_data"                                   
ag71xx_mdio: probed                                                             
eth0: Atheros AG71xx at 0xb9000000, irq 4                                       
eth0: no PHY found with phy_mask=00000008                                       
Atheros AR71xx hardware watchdog driver version 0.1.0                           
TCP westwood registered                                                         
NET: Registered protocol family 17                                              
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>                   
All bugs added by David S. Miller <davem@redhat.com>                            
VFS: Mounted root (squashfs filesystem) readonly on device 31:3.                
Freeing unused kernel memory: 148k freed                                        
Please be patient, while OpenWrt loads ...                                      
input: gpio-buttons as /devices/platform/gpio-buttons/input/input0              
Button Hotplug driver version 0.3.1                                             
- preinit -                                                                     
Registered led device: wp543:green:led1                                         
Registered led device: wp543:green:led2                                         
Registered led device: wp543:green:wlan                                         
Registered led device: wp543:green:conn                                         
Registered led device: wp543:green:diag                                         
Press the [f] key and hit [enter] to enter failsafe mode                        
- regular preinit -                                                             
switching to jffs2                                                              
mini_fo: using base directory: /                                                
mini_fo: using storage directory: /overlay                                      
- init -                                                                        
                                                                                
Please press Enter to activate this console. Compat-wireless backport release: 5
Backport based on wireless-testing.git master-2011-09-14                        
cfg80211: Calling CRDA to update world regulatory domain                        
usbcore: registered new interface driver usbfs                                  
usbcore: registered new interface driver hub                                    
cfg80211: World regulatory domain updated:                                      
cfg80211:     (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) 
cfg80211:     (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)      
cfg80211:     (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)      
cfg80211:     (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)      
cfg80211:     (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)      
cfg80211:     (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)      
usbcore: registered new device driver usb                                       
PCI: Enabling device 0000:00:12.0 (0000 -> 0002)                                
Registered led device: ath9k-phy0                                               
ieee80211 phy0: Atheros AR9280 Rev:2 mem=0xb0000000, irq=49                     
cfg80211: Calling CRDA for country: US                                          
cfg80211: Regulatory domain changed to country: US                              
cfg80211:     (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) 
cfg80211:     (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)      
cfg80211:     (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)      
cfg80211:     (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)      
cfg80211:     (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)      
cfg80211:     (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)      
cfg80211:     (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)      
PPP generic driver version 2.4.2                                                
ip_tables: (C) 2000-2006 Netfilter Core Team                                    
NET: Registered protocol family 24                                              
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver                      
ar71xx-ehci ar71xx-ehci: Atheros AR71xx built-in EHCI controller                
ar71xx-ehci ar71xx-ehci: new USB bus registered, assigned bus number 1          
ar71xx-ehci ar71xx-ehci: irq 3, io mem 0x1b000000                               
ar71xx-ehci ar71xx-ehci: USB 2.0 started, EHCI 1.00                             
usb usb1: configuration #1 chosen from 1 choice                                 
hub 1-0:1.0: USB hub found                                                      
hub 1-0:1.0: 2 ports detected                                                   
nf_conntrack version 0.5.0 (461 buckets, 1844 max)                              
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver                          
ar71xx-ohci ar71xx-ohci: Atheros AR71xx built-in OHCI controller                
ar71xx-ohci ar71xx-ohci: new USB bus registered, assigned bus number 2          
ar71xx-ohci ar71xx-ohci: irq 14, io mem 0x1c000000                              
usb usb2: configuration #1 chosen from 1 choice                                 
hub 2-0:1.0: USB hub found                                                      
hub 2-0:1.0: 2 ports detected                                                   
                                                                                
                                                                                
                                                                                
BusyBox v1.15.3 (2011-11-09 15:02:37 ART) built-in shell (ash)                  
Enter 'help' for a list of built-in commands.                                   
                                                                                
  _______                     ________        __                                
 |       |.-----.-----.-----.|  |  |  |.----.|  |_                              
 |   -   ||  _  |  -__|     ||  |  |  ||   _||   _|                             
 |_______||   __|_____|__|__||________||__|  |____|                             
          |__| W I R E L E S S   F R E E D O M                                  
 Backfire (10.03.1-RC6, r28875) --------------------                            
  * 1/3 shot Kahlua    In a shot glass, layer Kahlua                            
  * 1/3 shot Bailey's  on the bottom, then Bailey's,                            
  * 1/3 shot Vodka     then Vodka.                                              
 ---------------------------------------------------                            
root@OpenWrt:/# 

They are essentially the same except for the (i think) only relevant difference:

eth0: no PHY found with phy_mask=00000008                                       

If i find anything else i'll let you know

Best regards!

comment:4 follow-up: Changed 6 years ago by ericlarson@…

Hi.

I just tried 29328 for the WP543.

My ethernet port is getting recognized, but the problem I'm having appears to be with recognizing the PHY chip, an Atheros 8012-BG. Other boards with a 8012-A PHY seem to work fine.

Here is my dmesg output:

ag71xx_mdio: probed
eth0: Atheros AG71xx at 0xb9000000, irq 4
eth0: no PHY found with phy_mask=00000008
Atheros AR71xx hardware watchdog driver version 0.1.0

Thanks!

comment:5 in reply to: ↑ 4 ; follow-up: Changed 6 years ago by juhosg

  • Resolution set to fixed
  • Status changed from assigned to closed

Fixed in r29328 (trunk) and in r29334 (backfire). If you are updating an existing checkout, please run 'make target/linux/clean' after 'svn up'

comment:6 in reply to: ↑ 5 Changed 6 years ago by anonymous

Replying to juhosg:

Fixed in r29328 (trunk) and in r29334 (backfire). If you are updating an existing checkout, please run 'make target/linux/clean' after 'svn up'

This revision works on my hardware.

Thanks and best regards!

comment:7 Changed 6 years ago by ericlarson@…

Gabor,

Excellent! Of course. Sorry for the second note.

I would like to send you a bit of money via paypal. Can you please send me your paypal email address?

Thanks,

Eric.

Add Comment

Modify Ticket

Action
as closed .
The resolution will be deleted. Next status will be 'reopened'.
Author


E-mail address and user name can be saved in the Preferences.

 
Note: See TracTickets for help on using tickets.