Modify

Opened 7 years ago

Last modified 4 years ago

#7746 new task

new platform. D-LINK 615 A1 dir-615 a1

Reported by: cat Owned by: developers
Priority: normal Milestone: Features Paradise
Component: base system Version: Trunk
Keywords: switch 6061 DIR615A1 Cc: kaloz@…

Description

i Under the dir-615 gpl sourcecode to determine MPP_GPIO. Revised wnr854t.c Now, he can start properly, but the switch can not drive. The following is 615_setup.c file and start the log file.

I upgraded to 128 MB ram.:)

Thank you.

U-Boot 1.1.1 (Jan 19 2007 - 11:08:07)
CAMEO uBoot Linux Loader version: 1.3.0.0

DRAM CS[0] base 0x00000000   size 128MB 
DRAM Total size 128MB 
before entry mvFlashInit 
Flash: flashStructGet manu 0x89 id 0x17 
INTEL 28F640J3A (64 Mbit)
Size:  8 MB,Bus Width: 1, device Width: 1.
Flash base: 0xff800000,Number of Sectors: 64 Type: REGULAR.
  Sector Start Addresses:
    00000000      00020000      00040000      00060000      00080000     
    000a0000      000c0000      000e0000      00100000      00120000     
    00140000      00160000      00180000      001a0000      001c0000     
    001e0000      00200000      00220000      00240000      00260000     
    00280000      002a0000      002c0000      002e0000      00300000     
    00320000      00340000      00360000      00380000      003a0000     
    003c0000      003e0000      00400000      00420000      00440000     
    00460000      00480000      004a0000      004c0000      004e0000     
    00500000      00520000      00540000      00560000      00580000     
    005a0000      005c0000      005e0000      00600000      00620000     
    00640000      00660000      00680000      006a0000      006c0000     
    006e0000      00700000      00720000      00740000      00760000     
    00780000      007a0000      007c0000      007e0000     
[8192kB@ff800000] Flash:  8 MB
Addresses 20M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (20M - 16M): Done
*** Warning - bad CRC, using default environment


Soc: 88F5181 B1
CPU: ARM926 (Rev 0) running @ 500Mhz 
SysClock = 166Mhz , TClock = 166Mhz 


USB 0: host mode
PCI 0: PCI Express Root Complex Interface
PCI 1: Conventional PCI, speed = 33000000
Net:   egiga0 [PRIME]
Hit any key to stop autoboot:  0 
### JFFS2 loading 'uImage' to 0x400000
Scanning JFFS2 FS: . done.
### JFFS2 load complete: 954500 bytes loaded to 0x400000
## Booting image at 00400000 ...
   Image Name:   Linux-2.6.32.10
   Created:      2010-07-31  14:29:42 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    954436 Bytes = 932.1 kB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
OK

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
Linux version 2.6.32.10 (qwea@qwea-desktop) (gcc version 4.3.3 (GCC) ) #2 Sat Jul 31 22:29:34 CST 2010
CPU: Feroceon [41069260] revision 0 (ARMv5TEJ), cr=a0053177
CPU: VIVT data cache, VIVT instruction cache
Machine: D-LINK DIR615-A1
Clearing invalid memory bank 0KB@0xffffffff
Clearing invalid memory bank 0KB@0xffffffff
Clearing invalid memory bank 0KB@0xffffffff
Ignoring unrecognised tag 0x00000000
Ignoring unrecognised tag 0x00000000
Ignoring unrecognised tag 0x00000000
Memory policy: ECC disabled, Data cache writeback
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32512
Kernel command line: root=/dev/mtdblock1 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
PID hash table entries: 512 (order: -1, 2048 bytes)
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 128MB = 128MB total
Memory: 127116KB available (2400K code, 130K data, 92K init, 0K highmem)
Hierarchical RCU implementation.
NR_IRQS:64
Calibrating delay loop... 332.59 BogoMIPS (lpj=1662976)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16
Orion ID: MV88F5181-Rev-B1. TCLK=166666667.
Applying Orion-1/Orion-NAS PCIe config read transaction workaround
PCI: bus0: Fast back to back transfers disabled
pci 0000:01:00.0: PME# supported from D0 D1 D2 D3hot
pci 0000:01:00.0: PME# disabled
PCI: bus1: Fast back to back transfers enabled
bio: create slab <bio-0> at 0
Switching to clocksource orion_clocksource
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
NET: Registered protocol family 1
squashfs: version 4.0 (2009/01/31) Phillip Lougher
Registering mini_fo version $Id$
JFFS2 version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
msgmni has been set to 248
io scheduler noop registered
io scheduler deadline registered (default)
Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 3) is a 16550A
console [ttyS0] enabled
physmap platform flash device: 00800000 at f4000000
physmap-flash.0: Found 1 x16 devices at 0x0 in 8-bit bank
 Intel/Sharp Extended Query Table at 0x0031
 Intel/Sharp Extended Query Table at 0x0031
Using buffer write method
cfi_cmdset_0001: Erase suspend on write enabled
cmdlinepart partition parsing not available
RedBoot partition parsing not available
Using physmap partition information
Creating 4 MTD partitions on "physmap-flash.0":
0x000000000000-0x000000100000 : "kernel"
0x000000100000-0x000000760000 : "rootfs"
mtd: partition "rootfs" set to be root filesystem
mtd: partition "rootfs_data" created automatically, ofs=280000, len=4E0000 
0x000000280000-0x000000760000 : "rootfs_data"
0x000000760000-0x000000800000 : "uboot"
0x000000000000-0x000000760000 : "image"
MV-643xx 10/100/1000 ethernet driver version 1.4
mv643xx_eth smi: probed
net eth0: port 0 with MAC address 00:00:00:00:51:81
i2c /dev entries driver
Registered led device: dir615:green:WIRELESS_LED
Registered led device: dir615:green:STATUS_LED
Registered led device: dir615:green:USB_LED
TCP westwood registered
NET: Registered protocol family 17
Distributed Switch Architecture driver version 0.1
eth0[0]: could not detect attached switch
eth0[0]: couldn't create dsa switch instance (error -22)
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
VFS: Mounted root (squashfs filesystem) readonly on device 31:1.
Freeing init memory: 92K
Please be patient, while OpenWrt loads ...
- preinit -
Press the [f] key and hit [enter] to enter failsafe mode
- regular preinit -
switching to jffs2
mini_fo: using base directory: /
mini_fo: using storage directory: /overlay
- init -

Please press Enter to activate this console. Compat-wireless backport release: compat-wireless-2010-07-13-3-g1a05138
Backport based on wireless-2.6.git v2.6.35-rc5-47599-ge69e378
cfg80211: Calling CRDA to update world regulatory domain
cfg80211: World regulatory domain updated:
    (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
    (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
    (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
    (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
    (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
    (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
Registered led device: ath9k-phy0::radio
Registered led device: ath9k-phy0::assoc
Registered led device: ath9k-phy0::tx
Registered led device: ath9k-phy0::rx
phy0: Atheros AR5416 MAC/BB Rev:2 AR2133 RF Rev:81 mem=0xc8a80000, irq=36
cfg80211: Calling CRDA for country: AW
PPP generic driver version 2.4.2
cfg80211: Regulatory domain changed to country: AW
    (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
    (2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm)
    (5170000 KHz - 5250000 KHz @ 40000 KHz), (N/A, 2000 mBm)
    (5250000 KHz - 5330000 KHz @ 40000 KHz), (N/A, 2000 mBm)
    (5490000 KHz - 5710000 KHz @ 40000 KHz), (N/A, 2700 mBm)
ip_tables: (C) 2000-2006 Netfilter Core Team
NET: Registered protocol family 24
nf_conntrack version 0.5.0 (1990 buckets, 7960 max)
fuse init (API version 7.13)



BusyBox v1.15.3 (2010-07-31 00:48:03 CST) built-in shell (ash)
Enter 'help' for a list of built-in commands.

  _______                     ________        __
 |       |.-----.-----.-----.|  |  |  |.----.|  |_
 |   -   ||  _  |  -__|     ||  |  |  ||   _||   _|
 |_______||   __|_____|__|__||________||__|  |____|
          |__| W I R E L E S S   F R E E D O M
 Backfire (10.03, r22391) --------------------------
  * 1/3 shot Kahlua    In a shot glass, layer Kahlua 
  * 1/3 shot Bailey's  on the bottom, then Bailey's, 
  * 1/3 shot Vodka     then Vodka.
 ---------------------------------------------------
root@OpenWrt:/# 

Attachments (2)

dir615a1-setup.c (5.6 KB) - added by cat 7 years ago.
dir615_firmware.part2.rar (814.2 KB) - added by cat 7 years ago.

Download all attachments as: .zip

Change History (10)

Changed 7 years ago by cat

Changed 7 years ago by cat

comment:2 Changed 7 years ago by sniperpr@…

who has 88F5181_User_Manual.pdf

pleas upload.

comment:3 follow-up: Changed 7 years ago by nico

  • Milestone changed from Backfire 10.03.1 to Kamikaze Features Paradise
  • Priority changed from highest to normal
  • Version changed from Backfire 10.03 to Trunk

comment:4 in reply to: ↑ 3 Changed 7 years ago by anonymous

Replying to nico:

has Any 88e6061 switch fix about DIR-615 A1 (marvell 88f5181) ??

thanks.

comment:5 Changed 6 years ago by anonymous

dir615_firmware.part1.rar where ?

comment:6 Changed 6 years ago by anonymous

Please update us on the status of this device?
I see that dir615_firmware.part1.rar is missing.

comment:7 Changed 6 years ago by anonymous

why my dir 615a1 run uboot, but not ping pc! no tftp ! help me !!

comment:8 Changed 6 years ago by sniperpr@…

DSDP can be Device Switch.
but this FW not include DSDP.
so Switch Can't Work.

pleas go to D-LINK GPL site. check 615A1 sourcesource.

Add Comment

Modify Ticket

Action
as new .
Author


E-mail address and user name can be saved in the Preferences.

 
Note: See TracTickets for help on using tickets.