Modify

Opened 8 years ago

Closed 8 years ago

Last modified 23 months ago

#6812 closed defect (worksforme)

kamikaze trunk can't start RB433AH

Reported by: jetever@… Owned by: developers
Priority: high Milestone: Barrier Breaker 14.07
Component: base system Version: Kamikaze trunk
Keywords: Cc:

Description

RouterBOOT booter 2.19

RouterBoard 433AH

CPU frequency: 680 MHz

Memory size: 128 MB

Press any key within 2 seconds to enter setup..

loading kernel from nand... OK

setting up elf image...

when go to here, don't continue start.

please solve it. thanks

Attachments (0)

Change History (7)

comment:1 Changed 8 years ago by jetever@…

anyone can solve the problem?

comment:2 Changed 8 years ago by anonymous

Yes I get exactly the same here:

.......
loading kernel from nand... OK
setting up elf image...

comment:3 Changed 8 years ago by anonymous

Please solve this!

comment:4 Changed 8 years ago by juhosg

  • Resolution set to worksforme
  • Status changed from new to closed

Booting of the intramfs kernel:

RouterBOOT booter 2.15

RouterBoard 433AH

Authorization: Passed
CPU frequency: 680 MHz
  Memory size: 128 MB

Press any key within 4 seconds to enter setup.

RouterBOOT-2.15
What do you want to configure?
   d - boot delay
   k - boot key
   s - serial console
   o - boot device
   u - cpu mode
   f - cpu frequency
   r - reset booter configuration
   e - format nand
   g - upgrade firmware
   i - board info
   p - boot protocol
   x - exit setup
your choice: o - boot device

Select boot device:
 * e - boot over Ethernet
   n - boot from NAND, if fail then Ethernet
   1 - boot Ethernet once, then NAND
   o - boot from NAND only
   b - boot chosen device
your choice: b - boot chosen device
trying dhcp protocol... OK
resolved mac address 00:1F:D0:3F:39:3C
transfer started .............................. transfer ok, time=1.51s
setting up elf image... OK
jumping to kernel code
Linux version 2.6.32.9 (juhosg@idared) (gcc version 4.3.3 (GCC) ) #12 Tue Mar 9 21:36:31 CET 2010
bootconsole [early0] enabled
CPU revision is: 00019374 (MIPS 24Kc)
Atheros AR7161 rev 2, CPU:680.000 MHz, AHB:170.000 MHz, DDR:340.000 MHz
Determined physical RAM map:
 memory: 08000000 @ 00000000 (usable)
User-defined physical RAM map:
 memory: 08000000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Zone PFN ranges:
  Normal   0x00000000 -> 0x00008000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
    0: 0x00000000 -> 0x00008000
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32512
Kernel command line: rootfstype=squashfs,yaffs,jffs2 noinitrd console=ttyS0,115200 console=ttyS0,115200 gpio=4031 HZ=3
40000000 mem=128M kmac=00:0C:42:2D:B6:E4 board=433 boot=0
PID hash table entries: 512 (order: -1, 2048 bytes)
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
Writing ErrCtl register=00012000
Readback ErrCtl register=00012000
Memory: 125396k/131072k available (2027k kernel code, 5508k reserved, 523k data, 1336k init, 0k highmem)
SLUB: Genslabs=7, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Hierarchical RCU implementation.
NR_IRQS:56
Calibrating delay loop... 452.19 BogoMIPS (lpj=2260992)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
MIPS: machine is MikroTik RouterBOARD 433/AH
registering PCI controller with io_map_base unset
bio: create slab <bio-0> at 0
pci 0000:00:00.0: PME# supported from D0 D1 D2 D3hot
pci 0000:00:00.0: PME# disabled
Switching to clocksource MIPS
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
NET: Registered protocol family 1
squashfs: version 4.0 (2009/01/31) Phillip Lougher
Registering mini_fo version $Id$
JFFS2 version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
yaffs Mar  9 2010 09:16:07 Installing.
msgmni has been set to 245
io scheduler noop registered
io scheduler deadline registered (default)
Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A
console [ttyS0] enabled, bootconsole disabled
console [ttyS0] enabled, bootconsole disabled
NAND flash driver for RouterBoard 4xx series version 0.1.10
NAND SPI clock 28333 kHz (AHB 170000 kHz / 6)
FLASH SPI clock 28333 kHz (AHB 170000 kHz / 6)
NAND device: Manufacturer ID: 0xad, Chip ID: 0x76 (Hynix NAND 64MiB 3,3V 8-bit)
Scanning device for bad blocks
Creating 3 MTD partitions on "NAND 64MiB 3,3V 8-bit":
0x000000000000-0x000000040000 : "booter"
0x000000040000-0x000000400000 : "kernel"
0x000000400000-0x000004000000 : "rootfs"
mtd: partition "rootfs" set to be root filesystem
split_squashfs: no squashfs found in "NAND 64MiB 3,3V 8-bit"
Atheros AR71xx SPI Controller driver version 0.2.4
ag71xx_mdio: probed
eth0: Atheros AG71xx at 0xba000000, irq 5
eth1: Atheros AG71xx at 0xb9000000, irq 4
Atheros AR71xx hardware watchdog driver version 0.1.0
TCP westwood registered
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
Freeing unused kernel memory: 1336k freed
gpio-buttons driver version 0.1.2
input: gpio-buttons as /devices/platform/gpio-buttons/input/input0
Button Hotplug driver version 0.3.1
- preinit -
Registered led device: rb4xx:yellow:user
Press f<ENTER> to enter failsafe mode
- regular preinit -

Please press Enter to activate this console. device eth0 entered promiscuous mode
eth1: link up (100Mbps/Full duplex)
Generic kernel compatibility enabled based on linux-next next-20100113
cfg80211: Calling CRDA to update world regulatory domain
PPP generic driver version 2.4.2
ip_tables: (C) 2000-2006 Netfilter Core Team
NET: Registered protocol family 24
nf_conntrack version 0.5.0 (1982 buckets, 7928 max)
eth0: link up (100Mbps/Full duplex)
br-lan: port 1(eth0) entering forwarding state



BusyBox v1.15.3 (2010-03-09 20:58:41 CET) built-in shell (ash)
Enter 'help' for a list of built-in commands.

  _______                     ________        __
 |       |.-----.-----.-----.|  |  |  |.----.|  |_
 |   -   ||  _  |  -__|     ||  |  |  ||   _||   _|
 |_______||   __|_____|__|__||________||__|  |____|
          |__| W I R E L E S S   F R E E D O M
 KAMIKAZE (bleeding edge, r20099) ------------------
  * 10 oz Vodka       Shake well with ice and strain
  * 10 oz Triple sec  mixture into 10 shot glasses.
  * 10 oz lime juice  Salute!
 ---------------------------------------------------
root@OpenWrt:/#

Installing OpenWrt:

root@OpenWrt:/# wget2nand ftp://192.168.1.254:2121/openwrt
udhcpc (v1.15.3) started
Sending discover...
Sending select for 192.168.1.7...
Lease of 192.168.1.7 obtained, lease time 36000
udhcpc: ifconfig br-lan 192.168.1.7 netmask 255.255.255.0 broadcast +
Connecting to 192.168.1.254:2121 (192.168.1.254:2121)
kernel               100% |*******************************|  2735k 00:00:00 ETA
Connecting to 192.168.1.254:2121 (192.168.1.254:2121)
rootfs.tgz           100% |*******************************|  1710k 00:00:00 ETA
Erasing filesystem...
Mounting /dev/mtdblock2 as new root and /dev/mtdblock1 as kernel partition
yaffs: dev is 32505857 name is "mtdblock1"
yaffs: passed flags ""
yaffs: Attempting MTD mount on 31.1, "mtdblock1"
yaffs: auto selecting yaffs1
yaffs_read_super: isCheckpointed 0
yaffs: dev is 32505858 name is "mtdblock2"
yaffs: passed flags ""
yaffs: Attempting MTD mount on 31.2, "mtdblock2"
yaffs: auto selecting yaffs1
yaffs_read_super: isCheckpointed 0
Copying kernel...
Preparing filesystem...
./
./sys/
./mnt/
./proc/
./etc/
[...]
./bin/pwd
./bin/ps
./bin/egrep
./bin/mktemp
save exit: isCheckpointed 0
save exit: isCheckpointed 0
Cleaning up...
save exit: isCheckpointed 0
save exit: isCheckpointed 0
Image written, you can now reboot.  Remember to change the boot source to Boot from Nand
root@OpenWrt:/# 

Reboot:

root@OpenWrt:/# reboot
root@OpenWrt:/# br-lan: port 2(eth1) entering disabled state
device eth1 left promiscuous mode
br-lan: port 2(eth1) entering disabled state
device eth0 left promiscuous mode
br-lan: port 1(eth0) entering disabled state
eth1: link down
Restarting system.


RouterBOOT booter 2.15

RouterBoard 433AH

Authorization: Passed
CPU frequency: 680 MHz
  Memory size: 128 MB

Press any key within 4 seconds to enter setup....
Please, check ethernet cable...
Ethernet link absent...
trying dhcp protocol............................ failed
kernel loading failed


RouterBOOT booter 2.15

RouterBoard 433AH

Authorization: Passed
CPU frequency: 680 MHz
  Memory size: 128 MB

Press any key within 4 seconds to enter setup

RouterBOOT-2.15
What do you want to configure?
   d - boot delay
   k - boot key
   s - serial console
   o - boot device
   u - cpu mode
   f - cpu frequency
   r - reset booter configuration
   e - format nand
   g - upgrade firmware
   i - board info
   p - boot protocol
   x - exit setup
your choice: o - boot device

Select boot device:
 * e - boot over Ethernet
   n - boot from NAND, if fail then Ethernet
   1 - boot Ethernet once, then NAND
   o - boot from NAND only
   b - boot chosen device
your choice: n - boot from NAND, if fail then Ethernet

RouterBOOT-2.15
What do you want to configure?
   d - boot delay
   k - boot key
   s - serial console
   o - boot device
   u - cpu mode
   f - cpu frequency
   r - reset booter configuration
   e - format nand
   g - upgrade firmware
   i - board info
   p - boot protocol
   x - exit setup
your choice: x - exit setup


writing settings to flash... OK


RouterBOOT booter 2.15

RouterBoard 433AH

Authorization: Passed
CPU frequency: 680 MHz
  Memory size: 128 MB

Press any key within 4 seconds to enter setup....
loading kernel from nand... OK
setting up elf image... OK
jumping to kernel code
Linux version 2.6.32.9 (juhosg@idared) (gcc version 4.3.3 (GCC) ) #14 Wed Mar 10 08:33:17 CET 2010
bootconsole [early0] enabled
CPU revision is: 00019374 (MIPS 24Kc)
Atheros AR7161 rev 2, CPU:680.000 MHz, AHB:170.000 MHz, DDR:340.000 MHz
Determined physical RAM map:
 memory: 08000000 @ 00000000 (usable)
User-defined physical RAM map:
 memory: 08000000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Zone PFN ranges:
  Normal   0x00000000 -> 0x00008000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
    0: 0x00000000 -> 0x00008000
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32512
Kernel command line: rootfstype=squashfs,yaffs,jffs2 noinitrd console=ttyS0,115200 console=ttyS0,115200 gpio=4031 HZ=3
40000000 mem=128M kmac=00:0C:42:2D:B6:E4 board=433 boot=0
PID hash table entries: 512 (order: -1, 2048 bytes)
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
Writing ErrCtl register=00012000
Readback ErrCtl register=00012000
Memory: 126592k/131072k available (2000k kernel code, 4292k reserved, 518k data, 152k init, 0k highmem)
SLUB: Genslabs=7, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Hierarchical RCU implementation.
NR_IRQS:56
Calibrating delay loop... 452.19 BogoMIPS (lpj=2260992)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
MIPS: machine is MikroTik RouterBOARD 433/AH
registering PCI controller with io_map_base unset
bio: create slab <bio-0> at 0
pci 0000:00:00.0: PME# supported from D0 D1 D2 D3hot
pci 0000:00:00.0: PME# disabled
Switching to clocksource MIPS
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
NET: Registered protocol family 1
squashfs: version 4.0 (2009/01/31) Phillip Lougher
Registering mini_fo version $Id$
JFFS2 version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
yaffs Mar  9 2010 09:16:07 Installing.
msgmni has been set to 247
io scheduler noop registered
io scheduler deadline registered (default)
Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A
console [ttyS0] enabled, bootconsole disabled
console [ttyS0] enabled, bootconsole disabled
NAND flash driver for RouterBoard 4xx series version 0.1.10
NAND SPI clock 28333 kHz (AHB 170000 kHz / 6)
FLASH SPI clock 28333 kHz (AHB 170000 kHz / 6)
NAND device: Manufacturer ID: 0xad, Chip ID: 0x76 (Hynix NAND 64MiB 3,3V 8-bit)
Scanning device for bad blocks
Creating 3 MTD partitions on "NAND 64MiB 3,3V 8-bit":
0x000000000000-0x000000040000 : "booter"
0x000000040000-0x000000400000 : "kernel"
0x000000400000-0x000004000000 : "rootfs"
mtd: partition "rootfs" set to be root filesystem
split_squashfs: no squashfs found in "NAND 64MiB 3,3V 8-bit"
Atheros AR71xx SPI Controller driver version 0.2.4
ag71xx_mdio: probed
eth0: Atheros AG71xx at 0xba000000, irq 5
eth1: Atheros AG71xx at 0xb9000000, irq 4
Atheros AR71xx hardware watchdog driver version 0.1.0
TCP westwood registered
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
yaffs: dev is 32505858 name is "mtdblock2"
yaffs: passed flags ""
yaffs: Attempting MTD mount on 31.2, "mtdblock2"
yaffs_read_super: isCheckpointed 0
VFS: Mounted root (yaffs filesystem) readonly on device 31:2.
Freeing unused kernel memory: 152k freed
Please be patient, while OpenWrt loads ...
gpio-buttons driver version 0.1.2
input: gpio-buttons as /devices/platform/gpio-buttons/input/input0
Button Hotplug driver version 0.3.1
- preinit -
Registered led device: rb4xx:yellow:user
Press f<ENTER> to enter failsafe mode
- regular preinit -
- init -

Please press Enter to activate this console. device eth0 entered promiscuous mode
eth1: link up (100Mbps/Full duplex)
Generic kernel compatibility enabled based on linux-next next-20100113
cfg80211: Calling CRDA to update world regulatory domain
PPP generic driver version 2.4.2
ip_tables: (C) 2000-2006 Netfilter Core Team
NET: Registered protocol family 24
nf_conntrack version 0.5.0 (1983 buckets, 7932 max)
Driver for 1-wire Dallas network protocol.



BusyBox v1.15.3 (2010-03-09 20:58:41 CET) built-in shell (ash)
Enter 'help' for a list of built-in commands.

  _______                     ________        __
 |       |.-----.-----.-----.|  |  |  |.----.|  |_
 |   -   ||  _  |  -__|     ||  |  |  ||   _||   _|
 |_______||   __|_____|__|__||________||__|  |____|
          |__| W I R E L E S S   F R E E D O M
 KAMIKAZE (bleeding edge, r20099) ------------------
  * 10 oz Vodka       Shake well with ice and strain
  * 10 oz Triple sec  mixture into 10 shot glasses.
  * 10 oz lime juice  Salute!
 ---------------------------------------------------
root@OpenWrt:/#

comment:5 Changed 4 years ago by jow

  • Milestone changed from Attitude Adjustment 12.09 to Barrier Breaker 14.07

Milestone Attitude Adjustment 12.09 deleted

comment:6 Changed 23 months ago by anonymous

@ juhosg

Further I am trying for OVS configuration with same platform [RB433AH with Chaos Calmer 15.05]. I am confused with eth and wifi ports mapping. How should I add port to OVS and control flow via controller ?

comment:7 Changed 23 months ago by anonymous

@ jow

Further I am trying for OVS configuration with same platform [RB433AH with Chaos Calmer 15.05]. I am confused with eth and wifi ports mapping. How should I add port to OVS and control flow via controller ?

Add Comment

Modify Ticket

Action
as closed .
The resolution will be deleted. Next status will be 'reopened'.
Author


E-mail address and user name can be saved in the Preferences.

 
Note: See TracTickets for help on using tickets.