Modify

Opened 8 years ago

Closed 8 years ago

Last modified 4 years ago

#5837 closed defect (fixed)

ASUS WL-700ge - boot Kernel panic - not syncing: no init found

Reported by: m.delta@… Owned by: developers
Priority: highest Milestone: Barrier Breaker 14.07
Component: base system Version: Trunk
Keywords: boot mtdblock2 rootfs Cc:

Description

Hello,

Kernel panic - not syncing: No init found. Try passing init= option to kernel

Hi, I have a problem when boot ASUS WL-700gw to OpenWrt trunk version and kernel 2.6
Despite being set init=/dev/mtdblock2 the asus not boot and reports no sync.

Can this be fixed? Thanks a lot.

(In version 8.09.01 everything is fine again with a 2.6 kernel)

Boot sequence with last svn: 17573

CFE version 1.0.37 for BCM947XX (32bit,SP,LE)
Build Date: Ľ| 12¤ë 29 20:36:58 CST 2005 (root@localhost.localdomain)
Copyright (C) 2000,2001,2002,2003 Broadcom Corporation.

Initializing Arena
Initializing Devices.
et0: Broadcom BCM47xx 10/100 Mbps Ethernet Controller 3.90.23.0
rndis0: Broadcom USB RNDIS Network Adapter (P-t-P)
CPU type 0x29006: 264MHz
Total memory: 67108864 KBytes

Total memory used by CFE:  0x80800000 - 0x8089BA00 (637440)
Initialized Data:          0x80831B70 - 0x80834250 (9952)
BSS Area:                  0x80834250 - 0x80835A00 (6064)
Local Heap:                0x80835A00 - 0x80899A00 (409600)
Stack Area:                0x80899A00 - 0x8089BA00 (8192)
Text (code) segment:       0x80800000 - 0x80831B70 (203632)
Boot area (physical):      0x0089C000 - 0x008DC000
Relocation Factor:         I:00000000 - D:00000000

Device eth0:  hwaddr 00-17-31-BA-E4-3D, ipaddr 192.168.200.50, mask 255.255.255.0
        gateway not set, nameserver not set
Null Rescue Flag.
Null Restore Flag.
Welcome to Restore Mode: (by Force)

System will reboot after release reset buttom

set pivot_wait = 0
Loader:raw Filesys:raw Dev:flash0.os File: Options:(null)
Loading: .. 3768 bytes read
Entry at 0x80001000
Closing network.
Starting program at 0x80001000
Linux version 2.6.28.10 (broadcom@trixbox.nemtur.cz) (gcc version 4.1.2) #1 Sat Sep 12 22:02:24 CEST 2009
CPU revision is: 00029006 (Broadcom BCM3302)
Serial init done.
Determined physical RAM map:
 memory: 04000000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Zone PFN ranges:
  Normal   0x00000000 -> 0x00004000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
    0: 0x00000000 -> 0x00004000
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
Primary instruction cache 16kB, VIPT, 2-way, linesize 16 bytes.
Primary data cache 16kB, 2-way, VIPT, cache aliases, linesize 16 bytes
PID hash table entries: 256 (order: 8, 1024 bytes)
console [ttyS0] enabled
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 62144k/65536k available (2155k kernel code, 3316k reserved, 310k data, 136k init, 0k highmem)
Calibrating delay loop... 263.16 BogoMIPS (lpj=526336)
Mount-cache hash table entries: 512
net_namespace: 480 bytes
NET: Registered protocol family 16
pci 0000:00:03.0: PME# supported from D0 D1 D2 D3hot
pci 0000:00:03.0: PME# disabled
pci 0000:00:03.1: PME# supported from D0 D1 D2 D3hot
pci 0000:00:03.1: PME# disabled
pci 0000:00:03.2: PME# supported from D0 D1 D2 D3hot
pci 0000:00:03.2: PME# disabled
PCI: Enabling device 0000:00:01.0 (0000 -> 0002)
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
NET: Registered protocol family 1
detected lzma initramfs
initramfs: LZMA lc=1,lp=2,pb=2,origSize=512
squashfs: version 3.0 (2006/03/15) Phillip Lougher
Registering mini_fo version $Id$
JFFS2 version 2.2. (NAND) (SUMMARY)  Š 2001-2006 Red Hat, Inc.
msgmni has been set to 121
io scheduler noop registered
io scheduler deadline registered (default)
Serial: 8250/16550 driver2 ports, IRQ sharing enabled
serial8250: ttyS0 at MMIO 0xb8000300 (irq = 3) is a 16550A
serial8250: ttyS1 at MMIO 0xb8000400 (irq = 3) is a 16550A
serial8250.0: ttyS0 at MMIO 0xb8000300 (irq = 3) is a 16550A
serial8250.0: ttyS1 at MMIO 0xb8000400 (irq = 3) is a 16550A
b44.c:v2.0
eth0: Broadcom 44xx/47xx 10/100BaseT Ethernet 00:17:31:ba:e4:3d
b44: eth1: PHY Reset would not complete.
eth1: Broadcom 44xx/47xx 10/100BaseT Ethernet 40:10:18:00:00:2c
flash init: 0x1c000000 0x02000000
Physically mapped flash: Found 1 x16 devices at 0x0 in 16-bit bank
 Amd/Fujitsu Extended Query Table at 0x0040
Physically mapped flash: JEDEC Device ID is 0x22C4. Assuming broken CFI table.
Physically mapped flash: Swapping erase regions for broken CFI table.
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
Flash device: 0x200000 at 0x1fc00000
bootloader size: 262144
Creating 4 MTD partitions on "Physically mapped flash":
0x00000000-0x00040000 : "cfe"
0x00040000-0x001f0000 : "linux"
0x0010d800-0x001f0000 : "rootfs"
mtd: partition "rootfs" doesn't start on an erase block boundary -- force read-only
mtd: partition "rootfs" set to be root filesystem
mtd: partition "rootfs_data" created automatically, ofs=1B0000, len=40000
0x001b0000-0x001f0000 : "rootfs_data"
0x001f0000-0x00200000 : "nvram"
BCM47xx Watchdog Timer enabled (30 seconds, nowayout)
TCP westwood registered
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly.
Freeing unused kernel memory: 136k freed
Please be patient, while OpenWrt loads ...
Kernel panic - not syncing: No init found.  Try passing init= option to kernel.

Attachments (0)

Change History (3)

comment:1 Changed 8 years ago by m.delta@…

When I use official 8.09.1 svn 17317 then is all ok as shown here

flash init: 0x1c000000 0x02000000
Physically mapped flash: Found 1 x16 devices at 0x0 in 16-bit bank
 Amd/Fujitsu Extended Query Table at 0x0040
Physically mapped flash: CFI does not contain boot bank location. Assuming top.
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
Flash device: 0x200000 at 0x1fc00000
bootloader size: 262144
Updating TRX offsets and length:
old trx = [0x0000001c, 0x0000090c, 0x000b6c00], len=0x00181000 crc32=0x7d0b7b96
new trx = [0x0000001c, 0x0000090c, 0x000b6c00], len=0x000b6c00 crc32=0x86b234f0
Done
Creating 4 MTD partitions on "Physically mapped flash":
0x00000000-0x00040000 : "cfe"
0x00040000-0x001f0000 : "linux"
0x000f6c00-0x001f0000 : "rootfs"
mtd: partition "rootfs" doesn't start on an erase block boundary -- force read-only
mtd: partition "rootfs" set to be root filesystem
mtd: partition "rootfs_data" created automatically, ofs=1B0000, len=40000
0x001b0000-0x001f0000 : "rootfs_data"
0x001f0000-0x00200000 : "nvram"
TCP vegas registered
NET: Registered protocol family 1
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly.
Freeing unused kernel memory: 128k freed
Please be patient, while OpenWrt loads ...
Algorithmics/MIPS FPU Emulator v1.5
- preinit -
Press CTRL-C for failsafe
diag: Detected 'ASUS WL-700gE'
diag: Spinning up HDD and enabling leds
b44: eth0: Link is up at 100 Mbps, full duplex.
b44: eth0: Flow control is off for TX and off for RX.
roboswitch: Probing device eth0: found!
b44: eth0: powering down PHY
jffs2 not ready yet; using ramdisk
mini_fo: using base directory: /
mini_fo: using storage directory: /tmp/root
- init -

Please press Enter to activate this console. b44: eth0: Link is up at 100 Mbps, full duplex.
b44: eth0: Flow control is off for TX and off for RX.
br-lan: Dropping NETIF_F_UFO since no NETIF_F_HW_CSUM feature.
device eth0.0 entered promiscuous mode
device eth0 entered promiscuous mode
br-lan: port 1(eth0.0) entering learning state
br-lan: topology change detected, propagating
br-lan: port 1(eth0.0) entering forwarding state
Uniform Multi-Platform E-IDE driver
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
SCSI subsystem initialized
PCI: Enabling device 0000:00:02.0 (0000 -> 0003)
PCI: Fixing up device 0000:00:02.0
AEC6280: IDE controller (0x1191:0x0008 rev 0x10) at  PCI slot 0000:00:02.0
AEC6280: 100% native mode on irq 6
    ide2: BM-DMA at 0x0180-0x0187, BIOS settings: hde:PIO, hdf:PIO
    ide3: BM-DMA at 0x0188-0x018f, BIOS settings: hdg:PIO, hdh:PIO
hde: CF, ATA DISK drive
hde: applying conservative PIO "downgrade"
hde: host side 80-wire cable detection failed, limiting max speed to UDMA33
hde: UDMA/33 mode selected
ide2 at 0x100-0x107,0x10a on irq 6
br-lan: port 1(eth0.0) entering disabled state
br-lan: port 1(eth0.0) entering learning state
br-lan: topology change detected, propagating
br-lan: port 1(eth0.0) entering forwarding state
hde: max request size: 128KiB
hde: 15662304 sectors (8019 MB) w/1KiB Cache, CHS=15538/16/63
 hde: hde1 hde2

comment:2 Changed 8 years ago by tripolar

  • Resolution set to fixed
  • Status changed from new to closed

outdated bug - try latest build

comment:3 Changed 4 years ago by jow

  • Milestone changed from Attitude Adjustment 12.09 to Barrier Breaker 14.07

Milestone Attitude Adjustment 12.09 deleted

Add Comment

Modify Ticket

Action
as closed .
The resolution will be deleted. Next status will be 'reopened'.
Author


E-mail address and user name can be saved in the Preferences.

 
Note: See TracTickets for help on using tickets.