Modify

Opened 9 years ago

Closed 9 years ago

Last modified 4 years ago

#5447 closed defect (invalid)

adm5120 edimax board usb storage + madwifi / ath5k irq problem

Reported by: hanicka@… Owned by: developers
Priority: high Milestone: Barrier Breaker 14.07
Component: packages Version: Trunk
Keywords: madwifi ath5k adm5120 usb Cc:

Description (last modified by juhosg)

Hi, today I build r16662 on my router, I use usbroot, and after I installed ath5k or madwifi, system with both saying:

Linux version 2.6.28.10 (hanka@nimue.local) (gcc version 4.1.2) #10 Sat Jul 4 18:53:42 CEST 2009
console [early0] enabled
CPU revision is: 0001800b (MIPS 4Kc)
SoC      : ADM5120 rev 8, running at 175.000 MHz
Bootdev  : NOR flash
Prom     : Generic
Determined physical RAM map:
 memory: 02000000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Zone PFN ranges:
  Normal   0x00000000 -> 0x00002000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
    0: 0x00000000 -> 0x00002000
On node 0 totalpages: 8192
free_area_init_node: node 0, pgdat 802f1e60, node_mem_map 81000000
  Normal zone: 64 pages used for memmap
  Normal zone: 0 pages reserved
  Normal zone: 8128 pages, LIFO batch:0
  Movable zone: 0 pages used for memmap
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 8128
Kernel command line: console=ttyS0,115200 root=/dev/sda1 init=/etc/preinit ro rootdelay=10
Primary instruction cache 8kB, VIPT, 2-way, linesize 16 bytes.
Primary data cache 8kB, 2-way, VIPT, no aliases, linesize 16 bytes
PID hash table entries: 128 (order: 7, 512 bytes)
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Memory: 29200k/32768k available (2515k kernel code, 3568k reserved, 503k data, 140k init, 0k highmem)
SLUB: Genslabs=6, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Calibrating delay loop... 173.05 BogoMIPS (lpj=346112)
Mount-cache hash table entries: 512
net_namespace: 640 bytes
NET: Registered protocol family 16
MIPS: machine is Edimax BR-6104KP
registering PCI controller with io_map_base unset
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
pci 0000:00:00.0: reg 10 32bit mmio: [0xf0000000-0xffffffff]
pci 0000:00:02.0: reg 10 32bit mmio: [0x000000-0x00ffff]
PCI: pci_irq_map is not initialized
Switched to high resolution mode on CPU 0
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 1024 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP reno registered
NET: Registered protocol family 1
squashfs: version 3.0 (2006/03/15) Phillip Lougher
Registering mini_fo version $Id$
JFFS2 version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
yaffs Jul  4 2009 14:34:08 Installing. 
msgmni has been set to 57
io scheduler noop registered
io scheduler deadline registered (default)
Serial: AMBA driver
APB:UART0: ttyS0 at MMIO 0x12600000 (irq = 9) is a AMBA
console handover: boot [early0] -> real [ttyS0]
APB:UART1: ttyS1 at MMIO 0x12800000 (irq = 10) is a AMBA
ADM5120 built-in ethernet switch driver version 0.1.1
Driver 'sd' needs updating - please use bus_type methods
adm5120-flash.0: probing at 0x1FC00000, size:4096KiB, width:16 bits
adm5120-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank
 Amd/Fujitsu Extended Query Table at 0x0040
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
adm5120-flash.0: reduce visibility from 4096KiB to 4096KiB
adm5120-flash.0: found at 0x1FC00000, size:4096KiB, width:16 bits
adm5120-flash.0: adding static partitions
Creating 3 MTD partitions on "adm5120-flash.0":
0x00000000-0x00008000 : "admboot"
0x00008000-0x00010000 : "config"
0x00010000-0x00400000 : "firmware"
admhc-hcd: ADMtek USB 1.1 Host Controller Driver version 0.27.0
admhc-hcd: block sizes: ed 64 td 64
adm5120-hcd adm5120-hcd: ADM5120 built-in USB 1.1 Host Controller
adm5120-hcd adm5120-hcd: new USB bus registered, assigned bus number 1
adm5120-hcd adm5120-hcd: irq 11, io mem 0x11200000
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
adm5120_wdt: Watchdog Timer version 0.1
TCP westwood registered
NET: Registered protocol family 10
NET: Registered protocol family 17
Waiting 10sec before mounting root device...
usb 1-2: new full speed USB device using adm5120-hcd and address 2
usb 1-2: configuration #1 chosen from 1 choice
scsi0 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 2
usb-storage: waiting for device to settle before scanning
scsi 0:0:0:0: Direct-Access              USB FLASH DRIVE  PMAP PQ: 0 ANSI: 0 CCS
sd 0:0:0:0: [sda] 7831552 512-byte hardware sectors: (4.00 GB/3.73 GiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 23 00 00 00
sd 0:0:0:0: [sda] Assuming drive cache: write through
sd 0:0:0:0: [sda] 7831552 512-byte hardware sectors: (4.00 GB/3.73 GiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 23 00 00 00
sd 0:0:0:0: [sda] Assuming drive cache: write through
 sda: sda1
sd 0:0:0:0: [sda] Attached SCSI removable disk
sd 0:0:0:0: Attached scsi generic sg0 type 0
usb-storage: device scan complete
VFS: Mounted root (hfsplus filesystem) readonly.
Freeing unused kernel memory: 140k freed
Please be patient, while OpenWrt loads ...
gpio-buttons driver version 0.1.1
input: gpio-buttons as /devices/platform/gpio-buttons/input/input0
Button Hotplug driver version 0.3.1
Adding 262136k swap on /swap.  Priority:-1 extents:18 across:272108k
device eth0 entered promiscuous mode
br-lan: topology change detected, propagating
br-lan: port 1(eth0) entering forwarding state
wlan: trunk
ath_hal: module license 'Proprietary' taints kernel.
ath_hal: 2009-05-08 (AR5210, AR5211, AR5212, AR5416, RF5111, RF5112, RF2413, RF5413, RF2133, RF2425, REGOPS_FUNC, XR)
ath_rate_minstrel: Minstrel automatic rate control algorithm 1.2 (trunk)
ath_rate_minstrel: look around rate set to 10%
ath_rate_minstrel: EWMA rolloff level set to 75%
ath_rate_minstrel: max segment size in the mrr set to 6000 us
wlan: mac acl policy registered
ath_pci: trunk
PCI: Enabling device 0000:00:02.0 (0000 -> 0002)
wifi0: request_irq failed
eth0: no IPv6 routers present
adm5120_wdt: enabling watchdog timer

Attachments (1)

dmesg.txt (6.0 KB) - added by hanicka@… 9 years ago.
dmesg

Download all attachments as: .zip

Change History (5)

Changed 9 years ago by hanicka@…

dmesg

comment:1 Changed 9 years ago by hanicka@…

sorry for nonline breaking, dmesg is in attachment

comment:2 follow-up: Changed 9 years ago by juhosg

  • Description modified (diff)
  • Resolution set to invalid
  • Status changed from new to closed

This does not seems to be a BR-6104KP board. It has no PCI slot at all, thus the board setup code don't initialize the PCI IRQ map.

PCI: pci_irq_map is not initialized

You should use another firmware image which is compatible with your board.

comment:3 in reply to: ↑ 2 Changed 9 years ago by hanicka@…

Replying to juhosg:

This does not seems to be a BR-6104KP board. It has no PCI slot at all, thus the board setup code don't initialize the PCI IRQ map.

PCI: pci_irq_map is not initialized

You should use another firmware image which is compatible with your board.

Thanks, I have board Edimax BR-6524-WP (2 WANs, 4 LANs (one interface uses own NIC other then adm switch), 32MB ram, 4MB flash, 2 USB, 1 minipci). This board have no profile in openwrt, then I choose first similar. Where I can find change size limit for image?

comment:4 Changed 4 years ago by jow

  • Milestone changed from Attitude Adjustment 12.09 to Barrier Breaker 14.07

Milestone Attitude Adjustment 12.09 deleted

Add Comment

Modify Ticket

Action
as closed .
The resolution will be deleted. Next status will be 'reopened'.
Author


E-mail address and user name can be saved in the Preferences.

 
Note: See TracTickets for help on using tickets.