Modify

Opened 9 years ago

Closed 9 years ago

#4573 closed defect (invalid)

No USB on Ovislink MU-5000FS

Reported by: anonymous Owned by: developers
Priority: normal Milestone:
Component: packages Version:
Keywords: Cc:

Description

No USB available in OpenWrt revision 14393 on Ovislink MU-5000FS and Cellvision NFS-101U

transcription of boot log

PCI: Enabling device 0000:00:03.2 (0000 -> 0002)                                
ehci_hcd 0000:00:03.2: Found HC with no IRQ.  Check BIOS/PCI 0000:00:03.2 setup!
ehci_hcd 0000:00:03.2: init 0000:00:03.2 fail, -19                              
nf_conntrack version 0.5.0 (1024 buckets, 4096 max)                             
admhc-hcd: ADMtek USB 1.1 Host Controller Driver version 0.25.0                 
admhc-hcd: block sizes: ed 64 td 64                                             
PCI: Enabling device 0000:00:03.0 (0000 -> 0002)                                
ohci_hcd 0000:00:03.0: Found HC with no IRQ.  Check BIOS/PCI 0000:00:03.0 setup!
ohci_hcd 0000:00:03.0: init 0000:00:03.0 fail, -19                              
PCI: Enabling device 0000:00:03.1 (0000 -> 0002)                                
ohci_hcd 0000:00:03.1: Found HC with no IRQ.  Check BIOS/PCI 0000:00:03.1 setup!
ohci_hcd 0000:00:03.1: init 0000:00:03.1 fail, -19     

output of lspci -vv

root@hekate:/# lspci -vv                                                        
00:00.0 Host bridge: Linksys Unknown device 5120                                
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Ste-
        Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort--
        Latency: 0, Cache Line Size 04                                          
        Region 0: [virtual] Memory at f0000000 (32-bit, non-prefetchable) [size]
        Region 1: I/O ports at <unassigned>                                     
                                                                                
00:03.0 USB Controller: NEC Corporation USB (rev 43) (prog-if 10 [OHCI])        
        Subsystem: NEC Corporation USB                                          
        Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Ste-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbor-
        Interrupt: pin A routed to IRQ 0                                        
        Region 0: Memory at 11400000 (32-bit, non-prefetchable) [size=4K]       
        Capabilities: [40] Power Management version 2                           
                Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3ho)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-                     
                                                                                
00:03.1 USB Controller: NEC Corporation USB (rev 43) (prog-if 10 [OHCI])        
        Subsystem: NEC Corporation USB                                          
        Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Ste-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbor-
        Interrupt: pin B routed to IRQ 0                                        
        Region 0: Memory at 11401000 (32-bit, non-prefetchable) [size=4K]       
        Capabilities: [40] Power Management version 2                           
                Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3ho)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-                     
                                                                                
00:03.2 USB Controller: NEC Corporation USB 2.0 (rev 04) (prog-if 20 [EHCI])    
        Subsystem: NEC Corporation USB 2.0                                      
        Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Ste-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbor-
        Interrupt: pin C routed to IRQ 0                                        
        Region 0: Memory at 11402000 (32-bit, non-prefetchable) [size=256]      
        Capabilities: [40] Power Management version 2                           
                Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3ho)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME- 

Bug 4249 has handled this defect, is not fixed.

Attachments (0)

Change History (2)

comment:1 Changed 9 years ago by volker@…

Bus _is_ fixed. USB now working for storage and serial after cleaning my copy of OpenWrt trunk (revision 14419). Sorry for the disturbance. Please close this bug.

PCI: Enabling device 0000:00:03.2 (0000 -> 0002)
ehci_hcd 0000:00:03.2: EHCI Host Controller
ehci_hcd 0000:00:03.2: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:03.2: irq 16, io mem 0x11402000
ehci_hcd 0000:00:03.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 5 ports detected

usb 1-3: new high speed USB device using ehci_hcd and address 2
usb 1-3: configuration #1 chosen from 1 choice
PCI: Enabling device 0000:00:03.0 (0000 -> 0002)
ohci_hcd 0000:00:03.0: OHCI Host Controller
ohci_hcd 0000:00:03.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:03.0: irq 15, io mem 0x11400000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 3 ports detected
PCI: Enabling device 0000:00:03.1 (0000 -> 0002)
ohci_hcd 0000:00:03.1: OHCI Host Controller
ohci_hcd 0000:00:03.1: new USB bus registered, assigned bus number 3
ohci_hcd 0000:00:03.1: irq 16, io mem 0x11401000
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
usbcore: registered new interface driver usbserial
usbserial: USB Serial support registered for generic
usbcore: registered new interface driver usbserial_generic
usbserial: USB Serial Driver core
Initializing USB Mass Storage driver...
scsi0 : SCSI emulation for USB Mass Storage devices
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbserial: USB Serial support registered for FTDI USB Serial Device
usbcore: registered new interface driver ftdi_sio
ftdi_sio: v1.4.3:USB FTDI Serial Converters Driver
scsi 0:0:0:0: Direct-Access     SanDisk  Cruzer Mini      0.1  PQ: 0 ANSI: 2
sd 0:0:0:0: [sda] 1000944 512-byte hardware sectors (512 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Assuming drive cache: write through
sd 0:0:0:0: [sda] 1000944 512-byte hardware sectors (512 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Assuming drive cache: write through
 sda: sda1
sd 0:0:0:0: [sda] Attached SCSI removable disk
sd 0:0:0:0: Attached scsi generic sg0 type 0
yaffs: dev is 8388609 name is "sda1"
yaffs: passed flags ""
yaffs: Attempting MTD mount on 8.1, "sda1"
yaffs: dev is 8388609 name is "sda1"
yaffs: passed flags ""
yaffs: Attempting MTD mount on 8.1, "sda1"
EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended
usb 2-2: new full speed USB device using ohci_hcd and address 2
usb 2-2: configuration #1 chosen from 1 choice
ftdi_sio 2-2:1.0: FTDI USB Serial Device converter detected
ftdi_sio: Detected FT232BM
usb 2-2: FTDI USB Serial Device converter now attached to ttyUSB0

comment:2 Changed 9 years ago by juhosg

  • Resolution set to invalid
  • Status changed from new to closed

Add Comment

Modify Ticket

Action
as closed .
The resolution will be deleted. Next status will be 'reopened'.
Author


E-mail address and user name can be saved in the Preferences.

 
Note: See TracTickets for help on using tickets.