Modify

Opened 19 months ago

Last modified 19 months ago

#22874 new defect

15.05.1 r49400,wndr4300v1 no wireless.serial ouput shows ath9k error

Reported by: Halry Owned by: developers
Priority: highest Milestone: Designated Driver (Trunk)
Component: kernel Version: Trunk
Keywords: Cc:

Description

[    0.000000] Linux version 3.18.36 (halry@centos.virt) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r49400) ) #3 Tue Jul 19 20:48:48 CST 2016
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 0001974c (MIPS 74Kc)
[    0.000000] SoC: Atheros AR9344 rev 2
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 08000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x00000000-0x07ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x00000000-0x07ffffff]
[    0.000000] Initmem setup node 0 [mem 0x00000000-0x07ffffff]
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32512
[    0.000000] Kernel command line:  board=WNDR4300 console=ttyS0,115200 mtdparts=ar934x-nfc:256k(u-boot)ro,256k(u-boot-env)ro,256k(caldata),512k(pot),2048k(language),512k(config),3072k(traffic_meter),2048k(kernel),23552k(ubi),25600k@0x6c0000(firmware),256k(caldata_backup),-(reserved) rootfstype=squashfs noinitrd
[    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Writing ErrCtl register=00000000
[    0.000000] Readback ErrCtl register=00000000
[    0.000000] Memory: 124064K/131072K available (3937K kernel code, 142K rwdata, 948K rodata, 212K init, 190K bss, 7008K reserved)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS:51
[    0.000000] Clocks: CPU:560.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:40.000MHz
[    0.000000] Calibrating delay loop... 279.48 BogoMIPS (lpj=136192)
[    0.011718] pid_max: default: 32768 minimum: 301
[    0.012695] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.013671] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.017578] NET: Registered protocol family 16
[    0.019531] MIPS: machine is NETGEAR WNDR4300
[    0.227538] registering PCI controller with io_map_base unset
[    0.243163] PCI host bridge to bus 0000:00
[    0.244140] pci_bus 0000:00: root bus resource [mem 0x10000000-0x13ffffff]
[    0.245117] pci_bus 0000:00: root bus resource [io  0x0000]
[    0.246093] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[    0.247070] pci 0000:00:00.0: invalid calibration data
[    0.248046] pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x1001ffff 64bit]
[    0.249023] pci 0000:00:00.0: BAR 6: assigned [mem 0x10020000-0x1002ffff pref]
[    0.249999] pci 0000:00:00.0: using irq 40 for pin 1
[    0.251952] cfg80211: Calling CRDA to update world regulatory domain
[    0.254882] Switched to clocksource MIPS
[    0.259765] NET: Registered protocol family 2
[    0.265624] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    0.273437] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    0.280273] TCP: Hash tables configured (established 1024 bind 1024)
[    0.287109] TCP: reno registered
[    0.290038] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.296874] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.303710] NET: Registered protocol family 1
[    0.309570] futex hash table entries: 256 (order: -1, 3072 bytes)
[    0.332031] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.337890] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.349609] msgmni has been set to 242
[    0.356445] io scheduler noop registered
[    0.360351] io scheduler deadline registered (default)
[    0.366210] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[    0.374023] console [ttyS0] disabled
[    0.397460] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11, base_baud = 2500000) is a 16550A
[    0.406249] console [ttyS0] enabled
[    0.406249] console [ttyS0] enabled
[    0.414062] bootconsole [early0] disabled
[    0.414062] bootconsole [early0] disabled
[    0.424804] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xf1
[    0.431640] nand: Micron NAND 128MiB 3,3V 8-bit
[    0.435546] nand: 128MiB, SLC, page size: 2048, OOB size: 64
[    0.441406] Scanning device for bad blocks
[    0.531249] 12 cmdlinepart partitions found on MTD device ar934x-nfc
[    0.537109] Creating 12 MTD partitions on "ar934x-nfc":
[    0.542968] 0x000000000000-0x000000040000 : "u-boot"
[    0.548827] 0x000000040000-0x000000080000 : "u-boot-env"
[    0.554687] 0x000000080000-0x0000000c0000 : "caldata"
[    0.560546] 0x0000000c0000-0x000000140000 : "pot"
[    0.566405] 0x000000140000-0x000000340000 : "language"
[    0.572265] 0x000000340000-0x0000003c0000 : "config"
[    0.578124] 0x0000003c0000-0x0000006c0000 : "traffic_meter"
[    0.584960] 0x0000006c0000-0x0000008c0000 : "kernel"
[    0.590820] 0x0000008c0000-0x000001fc0000 : "ubi"
[    0.596679] 0x0000006c0000-0x000001fc0000 : "firmware"
[    0.958983] 0x000001fc0000-0x000002000000 : "caldata_backup"
[    0.964843] 0x000002000000-0x000008000000 : "reserved"
[    0.977538] switch0: Atheros AR8327 rev. 4 switch registered on ag71xx-mdio.0
[    1.037108] libphy: ag71xx_mdio: probed
[    1.597655] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.0:00 [uid=004dd034, driver=Atheros AR8216/AR8236/AR8316]
[    1.609374] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:RGMII
[    1.615233] PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
[    1.621092] ath9k 0000:00:00.0: Direct firmware load for pci_wmac0.eeprom failed with error -2
[    1.629881] ath9k 0000:00:00.0: Falling back to user helper
[    1.947264] random: nonblocking pool is initialized
[   61.749968] ath: phy0: Unable to load EEPROM file pci_wmac0.eeprom
[   61.755827] ath9k 0000:00:00.0: Failed to initialize device
[   61.761687] ath9k: probe of 0000:00:00.0 failed with error -22
[   61.769499] ledtrig-cpu: registered to indicate activity on CPUs
[   61.776335] netem: version 1.3
[   61.780241] u32 classifier
[   61.782194]     input device check on
[   61.786101]     Actions configured
[   61.790007] ipip: IPv4 over IPv4 tunneling driver
[   61.795866] gre: GRE over IPv4 demultiplexor driver
[   61.800749] TCP: cubic registered
[   61.804655] TCP: westwood registered
[   61.807585] TCP: highspeed registered
[   61.811491] TCP: hybla registered
[   61.815398] TCP: htcp registered
[   61.818327] TCP: vegas registered
[   61.821257] TCP: yeah registered
[   61.825163] NET: Registered protocol family 17
[   61.830046] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[   61.842741] 8021q: 802.1Q VLAN Support v1.8
[   61.846648] openvswitch: Open vSwitch switching datapath
[   61.852507] mpls_gso: MPLS GSO support
[   61.863249] UBI: auto-attach mtd8
[   61.867155] UBI: attaching mtd8 to ubi0
[   62.142546] UBI: scanning is finished
[   62.162077] UBI: attached mtd8 (name "ubi", size 23 MiB) to ubi0
[   62.168913] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[   62.175749] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[   62.182585] UBI: VID header offset: 2048 (aligned 2048), data offset: 4096
[   62.189421] UBI: good PEBs: 184, bad PEBs: 0, corrupted PEBs: 0
[   62.195280] UBI: user volume: 2, internal volumes: 1, max. volumes count: 128
[   62.203093] UBI: max/mean erase counter: 6/3, WL threshold: 4096, image sequence number: 584322263
[   62.211882] UBI: available PEBs: 0, total reserved PEBs: 184, PEBs reserved for bad PEB handling: 20
[   62.220671] UBI: background thread "ubi_bgt0d" started, PID 357
[   62.227507] UBI: ubiblock0_0 created from ubi0:0(rootfs)
[   62.233366] ubiblock: device ubiblock0_0 (rootfs) set to be root filesystem
[   62.240202] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[   62.247038] geneve: Geneve driver
[   62.257780] VFS: Mounted root (squashfs filesystem) readonly on device 254:0.
[   62.266569] Freeing unused kernel memory: 212K (8054b000 - 80580000)
[   63.431608] init: Console is alive
[   63.435514] init: - watchdog -
[   65.112271] usbcore: registered new interface driver usbfs
[   65.118130] usbcore: registered new interface driver hub
[   65.123990] usbcore: registered new device driver usb
[   65.133755] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[   65.142544] ehci-platform: EHCI generic platform driver
[   65.147427] ehci-platform ehci-platform: EHCI Host Controller
[   65.153286] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
[   65.164029] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
[   65.176724] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
[   65.183560] hub 1-0:1.0: USB hub found
[   65.187466] hub 1-0:1.0: 1 port detected
[   65.195279] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[   65.202115] ohci-platform: OHCI generic platform driver
[   65.513638] init: - preinit -
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[   68.011683] eth0: link up (1000Mbps/Full duplex)
[   68.398402] mount_root: loading kmods from internal overlay
[   68.834925] blk_update_request: I/O error, dev mtdblock4, sector 56
[   68.846644] blk_update_request: I/O error, dev mtdblock4, sector 56
[   68.846644] Buffer I/O error on dev mtdblock4, logical block 7, async page read
[   69.016566] UBIFS: background thread "ubifs_bgt0_1" starte

ath9k has error in new r49400 15.05.1?But my old build r49294 is fine.

Attachments (0)

Change History (1)

comment:1 Changed 19 months ago by Halry

In newest dd r49395,still has this problem.

Please press Enter to activate this console.
[   10.750107] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   10.767531] Netfilter messages via NETLINK v0.30.
[   10.775411] ip_set: protocol 6
[   10.816391] Loading modules backported from Linux version v4.4-rc5-1913-gc8fdf68
[   10.823904] Backport generated by backports.git backports-20151218-0-g2f58d9d
[   10.834593] ip_tables: (C) 2000-2006 Netfilter Core Team
[   10.852496] nf_conntrack version 0.5.0 (1958 buckets, 7832 max)
[   10.861940] ctnetlink v0.93: registering with nfnetlink.
[   10.903890] xt_time: kernel timezone is -0000
[   10.974469] PPP generic driver version 2.4.2
[   10.981733] NET: Registered protocol family 24
[   11.031892] ath9k ar934x_wmac: Direct firmware load for soc_wmac.eeprom failed with error -2
[   11.040525] ath9k ar934x_wmac: Falling back to user helper
[   11.226206] ieee80211 phy0: Atheros AR9340 Rev:2 mem=0xb8100000, irq=47
[   11.233099] PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
[   11.239756] ath9k 0000:00:00.0: Direct firmware load for pci_wmac0.eeprom failed with error -2
[   11.248554] ath9k 0000:00:00.0: Falling back to user helper
[   11.560393] ieee80211 phy1: Atheros AR9300 Rev:4 mem=0xb0000000, irq=40
[   24.704791] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   24.748588] device eth0 entered promiscuous mode
[   24.754836] device eth0.1 entered promiscuous mode
[   24.794685] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[   24.890846] IPv6: ADDRCONF(NETDEV_UP): eth0.2: link is not ready
[   25.907230] eth0: link up (1000Mbps/Full duplex)
[   25.912009] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   25.964380] br-lan: port 1(eth0.1) entered forwarding state
[   25.970134] br-lan: port 1(eth0.1) entered forwarding state
[   25.976078] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.2: link becomes ready
[   26.095906] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[   27.965910] br-lan: port 1(eth0.1) entered forwarding state
[   79.926961] Atheros AR8216/AR8236/AR8316 ag71xx-mdio.0:00: Port 4 is down

Add Comment

Modify Ticket

Action
as new .
Author


E-mail address and user name can be saved in the Preferences.

 
Note: See TracTickets for help on using tickets.