Modify

Opened 2 years ago

Last modified 2 years ago

#20635 new defect

ath10k_pci crashes at bootup

Reported by: paulc74 Owned by: developers
Priority: high Milestone: Chaos Calmer 15.05
Component: kernel Version: Trunk
Keywords: Cc: paulcabot47@…

Description

When then the ath10k_pci module loads up at boot. It crashes with the following errors

[    9.411724] ath10k_pci 0000:05:00.0: enabling device (0140 -> 0142)
[    9.418662] ath10k_pci 0000:05:00.0: pci irq legacy interrupts 0 irq_mode 0 reset_mode 0
[    9.640636] ath10k_pci 0000:05:00.0: Direct firmware load for ath10k/cal-pci-0000:05:00.0.bin failed with error -2
[    9.651056] ath10k_pci 0000:05:00.0: Falling back to user helper
[    9.669727] firmware ath10k!cal-pci-0000:05:00.0.bin: firmware_loading_store: map pages failed
[   11.815657] ath10k_pci 0000:05:00.0: failed to receive control response completion, polling..
[   12.815651] ath10k_pci 0000:05:00.0: Service connect timeout: 0
[   12.821596] ath10k_pci 0000:05:00.0: failed to connect htt (-110)
[   12.928246] ath10k_pci 0000:05:00.0: could not init core (-110)
[   12.934233] ath10k_pci 0000:05:00.0: could not probe fw (-110)

After boot up if I rmmod ath10k_pci and then modprobe ath10k_pci. It sometimes loads without crashing.

Attachments (0)

Change History (4)

comment:1 Changed 2 years ago by florian

What exact OpenWrt revision are you seeing this with? What is your device brand and model?

comment:2 Changed 2 years ago by paulc74

Currently at revision r47072

Device is a Gateworks Ventana GW5310

EDIT: Forgot to mention the radio card is a doodle labs ACE-DB-3

Last edited 2 years ago by paulc74 (previous) (diff)

comment:3 Changed 2 years ago by diizzyy@…

Does the still happen on a recent trunk build?

comment:4 Changed 2 years ago by paulc74

 ath10k_pci 0000:05:00.0: enabling device (0140 -> 0142)
[    9.321099] ath10k_pci 0000:05:00.0: pci irq legacy interrupts 0 irq_mode 0 reset_mode 0
[    9.541297] ath10k_pci 0000:05:00.0: Direct firmware load for ath10k/cal-pci-0000:05:00.0.bin failed with error -2
[    9.551695] ath10k_pci 0000:05:00.0: Falling back to user helper
[    9.566773] firmware ath10k!cal-pci-0000:05:00.0.bin: firmware_loading_store: map pages failed
[    9.681825] ath10k_pci 0000:05:00.0: qca988x hw2.0 target 0x4100016c chip_id 0x043202ff sub 0000:0000
[    9.691119] ath10k_pci 0000:05:00.0: kconfig debug 1 debugfs 1 tracing 0 dfs 1 testmode 1
[    9.702943] ath10k_pci 0000:05:00.0: firmware ver 10.2.4.97 api 5 features no-p2p crc32 f91e34f2
[    9.752370] ath10k_pci 0000:05:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/board-2.bin failed with error -2
[    9.762842] ath10k_pci 0000:05:00.0: Falling back to user helper
[    9.777698] firmware ath10k!QCA988X!hw2.0!board-2.bin: firmware_loading_store: map pages failed
[    9.796193] ath10k_pci 0000:05:00.0: board_file api 1 bmi_id N/A crc32 bebc7c08
[   10.954325] ath10k_pci 0000:05:00.0: htt-ver 2.1 wmi-op 5 htt-op 2 cal otp max-sta 128 raw 0 hwcrypto 1

This is the message I get with revision r48626

It doesn't appear to be crashing any more. But I'm still getting an error message when the firmware is loaded. This might be a different issue though. If you feel it is then close off this ticket.

Add Comment

Modify Ticket

Action
as new .
Author


E-mail address and user name can be saved in the Preferences.

 
Note: See TracTickets for help on using tickets.