Modify

Opened 3 years ago

Last modified 2 years ago

#20042 assigned defect

WRTU54G-TM bricked by Chaos Calmer 15.05 RC2

Reported by: wayne@… Owned by: florian
Priority: normal Milestone: Chaos Calmer 15.05
Component: packages Version: Trunk
Keywords: Cc:

Description

I downloaded the latest release candidate image here:

https://downloads.openwrt.org/chaos_calmer/15.05-rc2/adm8668/generic/openwrt-15.05-rc2-adm8668-squashfs.bin

I renamed it to "WRTU54G-TM_v1.00.26.bin" and loaded it using the Linksys firmware update web GUI.

The router no longer functions.

Attachments (0)

Change History (8)

comment:1 Changed 3 years ago by anonymous

try telnet / ssh. if you'd read up on things you would have seen that RC2 has a bug where it behaves as if it was trunk and does not install a web interface.

to fix it, as root logged via telnet / ssh:

# cp /rom/etc/opkg.conf /etc/opkg.conf
# opkg update
# opkg install luci

(the luci install will pull with it the uhttpd web server too)

comment:2 Changed 3 years ago by wayne@…

Thanks for the suggestion. The router no longer responds to DHCP requests. If I setup a static on my computer, the router does not respond to ping 192.168.1.1 and fails telnet connection attempts on ports 22 and 23.

comment:3 Changed 3 years ago by wayne@…

(just to be clear the static address I used on the computer for the ping and telnet tests was 192.168.1.10 with subnet 255.255.255.0.)

comment:4 Changed 3 years ago by wayne@…

Captured a boot log over the serial port:

(v1.00.02) U-Boot 2.1.4 (Jan 28 2008 - 14:56:42)

DRAM: 64 MB
Flash: 8 MB
In: serial
Out: serial
Err: serial
Net: adm8668_net
Hit any key to stop autoboot: 1 ### 0
## Booting image at b0040000 ...
Check vendor string... Image Name: ADM8668 Linux Kernel(2.4.31)

Created: 2015-06-08 14:13:35 UTC
Image Type: MIPS Linux Kernel Image (uncompressed)
Data Size: 3669952 Bytes = 3.5 MB
Load Address: 80400000
Entry Point: 80400000
Verifying Checksum ... OK

OK

Starting kernel ...

LZMA kernel loader
lzma data @ 0x804001d0 - 0x80530470
load addr @ 0x80002000

jump table @ 0x83ff5340

Decompressing kernel...success!
[ 0.000000] Linux version 3.18.14 (buildbot@builder1) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r45872) ) #1 Mon Jun 8 16:13:23 CEST 2015
[ 0.000000] Board info:
[ 0.000000] RAM size: 64 MB
[ 0.000000] NOR start: 0xb0000000
[ 0.000000] NOR size: 0x800000
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 0001800b (MIPS 4Kc)
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x00000000-0x03ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x03ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x00000000-0x03ffffff]
[ 0.000000] Primary instruction cache 8kB, VIPT, 2-way, linesize 16 bytes.
[ 0.000000] Primary data cache 8kB, 2-way, VIPT, no aliases, linesize 16 bytes
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
[ 0.000000] Kernel command line: console=ttyS0 earlyprintk
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Memory: 61136K/65536K available (2850K kernel code, 90K rwdata, 496K rodata, 132K init, 189K bss, 4400K reserved)
[ 0.000000] NR_IRQS:32
[ 0.000000] ADM8668 CPU clock: 200 MHz
[ 0.000000] Calibrating delay loop... 199.06 BogoMIPS (lpj=995328)
[ 0.070000] pid_max: default: 32768 minimum: 301
[ 0.070000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.080000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.110000] NET: Registered protocol family 16
[ 0.120000] ------------[ cut here ]------------
[ 0.120000] WARNING: CPU: 0 PID: 1 at drivers/amba/bus.c:305 amba_device_add+0x64/0x25c()
[ 0.130000] Modules linked in:
[ 0.130000] CPU: 0 PID: 1 Comm: swapper Not tainted 3.18.14 #1
[ 0.130000] Stack : 00000000 00000000 00000000 00000000 80383f52 00000032 00000000 00000000

80383f52 8035f300 802fbba8 80350be3 00000001 80383190 8381bc00 8035f300
8037775c 80380000 00000020 8004f8e0 00000003 80026d04 00000131 8035f300
802ffb24 8381fd5c 00000000 00000000 00000000 00000000 00000000 00000000
00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
...

[ 0.170000] Call Trace:
[ 0.170000] [<800137e8>] show_stack+0x48/0x70
[ 0.170000] [<80026e10>] warn_slowpath_common+0x84/0xb4
[ 0.180000] [<80026ec8>] warn_slowpath_null+0x18/0x24
[ 0.180000] [<801a2e10>] amba_device_add+0x64/0x25c
[ 0.180000] [<80361b4c>] adm8668_devs_register+0x1c/0xcc
[ 0.190000] [<8000c0c0>] do_one_initcall+0x140/0x218
[ 0.190000] [<8035fd04>] kernel_init_freeable+0x144/0x20c
[ 0.190000] [<80006acc>] kernel_init+0x10/0x114
[ 0.200000] [<800020a8>] ret_from_kernel_thread+0x14/0x1c
[ 0.200000]
[ 0.210000] ---[ end trace ac266e7a3f8107e6 ]---
[ 0.210000] ADM8668: applied USB workaround
[ 0.240000] PCI host bridge to bus 0000:00
[ 0.250000] pci_bus 0000:00: root bus resource [mem 0x16000000-0x1dffffff]
[ 0.250000] pci_bus 0000:00: root bus resource [io 0x12600000-0x127fffff]
[ 0.260000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 0.260000] PCI: fixing up ADM8668 controller
[ 0.270000] pci 0000:00:01.0: BAR 0: assigned [mem 0x16000000-0x16007fff]
[ 0.280000] Switched to clocksource MIPS
[ 0.290000] NET: Registered protocol family 2
[ 0.300000] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.300000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.310000] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.320000] TCP: reno registered
[ 0.320000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.320000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.330000] NET: Registered protocol family 1
[ 0.340000] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.350000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.360000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.370000] msgmni has been set to 119
[ 0.370000] io scheduler noop registered
[ 0.380000] io scheduler deadline registered (default)
[ 0.380000] Serial: AMBA driver
[ 0.390000] apb:uart0: ttyS0 at MMIO 0x1e400000 (irq = 6, base_baud # J# ootconsole [early0] disabled
[ 0.410000] adm8668-nor: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x0022cb
[ 0.420000] Amd/Fujitsu Extended Query Table at 0x0040
[ 0.430000] Amd/Fujitsu Extended Query version 1.1.
[ 0.440000] number of CFI chips: 1
[ 0.440000] adm8668-nor: Couldn't find root filesystem
[ 0.540000] Creating 3 MTD partitions on "adm8668-nor":
[ 0.540000] 0x000000040000-0x000000800000 : "linux"
[ 0.550000] 0x0000000e0000-0x000000220000 : "rootfs"
[ 0.560000] mtd: device 1 (rootfs) set to be root filesystem
[ 0.570000] mtdsplit: no squashfs found in "rootfs"
[ 0.580000] mtdsplit: no squashfs found in "adm8668-nor"
[ 0.580000] 0x000000020000-0x000000040000 : "uboot_env"
[ 0.600000] net eth0: tulip_platform (Infineon ADM8668) at MMIO 0x11a00000 00:1e:e5:b9:ef:b9, IRQ 7
[ 0.610000] net eth1: tulip_platform (Infineon ADM8668) at MMIO 0x11600000 00:1e:e5:b9:ef:ba, IRQ 8
[ 0.620000] TCP: cubic registered
[ 0.630000] NET: Registered protocol family 17
[ 0.630000] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[ 0.650000] Bridge firewalling registered
[ 0.650000] 8021q: 802.1Q VLAN Support v1.8
[ 0.690000] List of all partitions:
[ 0.690000] 1f00 7936 mtdblock0 (driver?)
[ 0.700000] 1f01 1280 mtdblock1 (driver?)
[ 0.700000] 1f02 128 mtdblock2 (driver?)
[ 0.710000] No filesystem could mount root, tried: squashfs
[ 0.710000] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(31,1)
[ 0.710000] ---[ end Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(31,1)

comment:5 Changed 3 years ago by wayne@…

I got my WRTU54G-TM working again. I was able to load an older version of OpenWRT by using the on-board serial port to initiate a TFTP update. The version of OpenWRT that I installed is here:

https://downloads.openwrt.org/attitude_adjustment/12.09/adm8668/generic/openwrt-adm8668-squashfs.bin

Rescue was made possible by these helpful pages:
http://pstjuste.blogspot .com/2013/10/unbricking-my-linksys-wrtu54g-tm-from.html
http://wiki.scottn.us/wrtu54g-tm:uboot
http://wiki.scottn.us/wrtu54g-tm:info#serial_port

(sorry, you'll have to manually remove the space from blogspot link. Antispam filter wouldn't allow it.)

comment:6 Changed 2 years ago by rayknight

RC3 Still has issue. Below is boot log from serial console:

@@07f?4

(v0.73.00) U-Boot 2.1.4 (Nov 6 2007 - 12:47:31)

DRAM: 64 MB
Flash: 8 MB
In: serial
Out: serial
Err: serial
Net: adm8668_net
Hit any key to stop autoboot: 0
## Booting image at b0040000 ...
Check vendor string... Image Name: ADM8668 Linux Kernel(2.4.31)

Created: 2015-07-03 20:18:51 UTC
Image Type: MIPS Linux Kernel Image (uncompressed)
Data Size: 3669952 Bytes = 3.5 MB
Load Address: 80400000
Entry Point: 80400000
Verifying Checksum ... OK

OK

Starting kernel ...

LZMA kernel loader
lzma data @ 0x804001d0 - 0x8053080c
load addr @ 0x80002000

jump table @ 0x83ff5330

Decompressing kernel...success!
[ 0.000000] Linux version 3.18.17 (buildbot@builder1) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r46018) ) #1 Fri Jul 3 22:18:30 CEST 2015
[ 0.000000] Board info:
[ 0.000000] RAM size: 64 MB
[ 0.000000] NOR start: 0xb0000000
[ 0.000000] NOR size: 0x800000
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 0001800b (MIPS 4Kc)
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x00000000-0x03ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x03ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x00000000-0x03ffffff]
[ 0.000000] Primary instruction cache 8kB, VIPT, 2-way, linesize 16 bytes.
[ 0.000000] Primary data cache 8kB, 2-way, VIPT, no aliases, linesize 16 bytes
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
[ 0.000000] Kernel command line: console=ttyS0 earlyprintk
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Memory: 61136K/65536K available (2852K kernel code, 88K rwdata, 496K rodata, 132K init, 189K bss, 4400K reserved)
[ 0.000000] NR_IRQS:32
[ 0.000000] ADM8668 CPU clock: 200 MHz
[ 0.000000] Calibrating delay loop... 199.06 BogoMIPS (lpj=995328)
[ 0.070000] pid_max: default: 32768 minimum: 301
[ 0.070000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.080000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.110000] NET: Registered protocol family 16
[ 0.120000] ------------[ cut here ]------------
[ 0.120000] WARNING: CPU: 0 PID: 1 at drivers/amba/bus.c:305 amba_device_add+0x64/0x25c()
[ 0.130000] Modules linked in:
[ 0.130000] CPU: 0 PID: 1 Comm: swapper Not tainted 3.18.17 #1
[ 0.130000] Stack : 00000000 00000000 00000000 00000000 80383f52 00000032 00000000 00000000

80383f52 8035f300 802fbc48 80350be3 00000001 80383190 8381bc00 8035f300
8037775c 80380000 00000020 8004f978 00000003 80026d04 00000131 8035f300
802ffbc4 8381fd5c 00000000 00000000 00000000 00000000 00000000 00000000
00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
...

[ 0.170000] Call Trace:
[ 0.170000] [<800137e8>] show_stack+0x48/0x70
[ 0.170000] [<80026e10>] warn_slowpath_common+0x84/0xb4
[ 0.180000] [<80026ec8>] warn_slowpath_null+0x18/0x24
[ 0.180000] [<801a300c>] amba_device_add+0x64/0x25c
[ 0.180000] [<80361b4c>] adm8668_devs_register+0x1c/0xcc
[ 0.190000] [<8000c0c0>] do_one_initcall+0x140/0x218
[ 0.190000] [<8035fd04>] kernel_init_freeable+0x144/0x20c
[ 0.190000] [<80006acc>] kernel_init+0x10/0x114
[ 0.200000] [<800020a8>] ret_from_kernel_thread+0x14/0x1c
[ 0.200000]
[ 0.210000] ---[ end trace 1b91f31f10f6ff33 ]---
[ 0.210000] ADM8668: applied USB workaround
[ 0.240000] PCI host bridge to bus 0000:00
[ 0.250000] pci_bus 0000:00: root bus resource [mem 0x16000000-0x1dffffff]
[ 0.250000] pci_bus 0000:00: root bus resource [io 0x12600000-0x127fffff]
[ 0.260000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 0.260000] PCI: fixing up ADM8668 controller
[ 0.270000] pci 0000:00:01.0: BAR 0: assigned [mem 0x16000000-0x16007fff]
[ 0.280000] Switched to clocksource MIPS
[ 0.290000] NET: Registered protocol family 2
[ 0.300000] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.300000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.310000] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.320000] TCP: reno registered
[ 0.320000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.320000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.330000] NET: Registered protocol family 1
[ 0.340000] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.350000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.360000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.370000] msgmni has been set to 119
[ 0.370000] io scheduler noop registered
[ 0.380000] io scheduler deadline registered (default)
[ 0.380000] Serial: AMBA driver
[ 0.390000] apb:uart0: ttyS0 at MMIO 0x1e400000 (irq = 6, base_baud E<82>JBJ́a AMBA
[ 0.390000] console [ttyS0] enabled
[ 0.390000] console [ttyS0] enabled
[ 0.400000] bootconsole [early0] disabled
[ 0.400000] bootconsole [early0] disabled
[ 0.410000] adm8668-nor: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x0022cb
[ 0.420000] Amd/Fujitsu Extended Query Table at 0x0040
[ 0.430000] Amd/Fujitsu Extended Query version 1.1.
[ 0.440000] number of CFI chips: 1
[ 0.440000] adm8668-nor: Couldn't find root filesystem
[ 0.540000] Creating 3 MTD partitions on "adm8668-nor":
[ 0.540000] 0x000000040000-0x000000800000 : "linux"
[ 0.550000] 0x0000000e0000-0x000000220000 : "rootfs"
[ 0.560000] mtd: device 1 (rootfs) set to be root filesystem
[ 0.570000] mtdsplit: no squashfs found in "rootfs"
[ 0.580000] mtdsplit: no squashfs found in "adm8668-nor"
[ 0.580000] 0x000000020000-0x000000040000 : "uboot_env"
[ 0.600000] net eth0: tulip_platform (Infineon ADM8668) at MMIO 0x11a00000 00:1e:e5:b1:98:fa, IRQ 7
[ 0.610000] net eth1: tulip_platform (Infineon ADM8668) at MMIO 0x11600000 00:1e:e5:b1:98:fb, IRQ 8
[ 0.620000] TCP: cubic registered
[ 0.630000] NET: Registered protocol family 17
[ 0.630000] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[ 0.650000] Bridge firewalling registered
[ 0.650000] 8021q: 802.1Q VLAN Support v1.8
[ 0.690000] List of all partitions:
[ 0.700000] 1f00 7936 mtdblock0 (driver?)
[ 0.700000] 1f01 1280 mtdblock1 (driver?)
[ 0.710000] 1f02 128 mtdblock2 (driver?)
[ 0.710000] No filesystem could mount root, tried: squashfs
[ 0.720000] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(31,1)
[ 0.720000] ---[ end Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(31,1)

Looks like an issue with the driver for MTD.

comment:7 Changed 2 years ago by florian

  • Owner changed from developers to florian
  • Status changed from new to assigned

comment:8 Changed 2 years ago by rayknight

Still an issue with the final 15.05 release. Below is the boot log:

07f?4

(v0.73.00) U-Boot 2.1.4 (Nov 6 2007 - 12:47:31)

DRAM: 64 MB
Flash: 8 MB
In: serial
Out: serial
Err: serial
Net: adm8668_net
Hit any key to stop autoboot: 0
## Booting image at b0040000 ...
Check vendor string... Image Name: ADM8668 Linux Kernel(2.4.31)

Created: 2015-09-04 19:32:14 UTC
Image Type: MIPS Linux Kernel Image (uncompressed)
Data Size: 3538880 Bytes = 3.4 MB
Load Address: 80400000
Entry Point: 80400000
Verifying Checksum ... OK

OK

Starting kernel ...

LZMA kernel loader
lzma data @ 0x804001d0 - 0x8051a130
load addr @ 0x80002000

jump table @ 0x83ff5330

Decompressing kernel...success!
[ 0.000000] Linux version 3.18.20 (buildbot@builder1) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r46450) ) #1 Fri Sep 4 21:31:59 CEST 2015
[ 0.000000] Board info:
[ 0.000000] RAM size: 64 MB
[ 0.000000] NOR start: 0xb0000000
[ 0.000000] NOR size: 0x800000
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 0001800b (MIPS 4Kc)
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x00000000-0x03ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x03ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x00000000-0x03ffffff]
[ 0.000000] Primary instruction cache 8kB, VIPT, 2-way, linesize 16 bytes.
[ 0.000000] Primary data cache 8kB, 2-way, VIPT, no aliases, linesize 16 bytes
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
[ 0.000000] Kernel command line: console=ttyS0 earlyprintk
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Memory: 61328K/65536K available (2843K kernel code, 85K rwdata, 316K rodata, 132K init, 189K bss, 4208K reserved)
[ 0.000000] NR_IRQS:32
[ 0.000000] ADM8668 CPU clock: 200 MHz
[ 0.000000] Calibrating delay loop... 199.06 BogoMIPS (lpj=995328)
[ 0.070000] pid_max: default: 32768 minimum: 301
[ 0.070000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.080000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.110000] NET: Registered protocol family 16
[ 0.110000] ------------[ cut here ]------------
[ 0.120000] WARNING: CPU: 0 PID: 1 at drivers/amba/bus.c:305 0x801a0df8()
[ 0.120000] Modules linked in:
[ 0.120000] CPU: 0 PID: 1 Comm: swapper Not tainted 3.18.20 #1
[ 0.130000] Stack : 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000

00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
...

[ 0.160000] Call Trace:[<800133a8>] 0x800133a8
[ 0.160000] [<800133a8>] 0x800133a8
[ 0.170000] [<800269d0>] 0x800269d0
[ 0.170000] [<801a0df8>] 0x801a0df8
[ 0.170000] [<80026a88>] 0x80026a88
[ 0.180000] [<80168480>] 0x80168480
[ 0.180000] [<801a1024>] 0x801a1024
[ 0.180000] [<801a0df8>] 0x801a0df8
[ 0.190000] [<801a1108>] 0x801a1108
[ 0.190000] [<80331a78>] 0x80331a78
[ 0.190000] [<8032f248>] 0x8032f248
[ 0.200000] [<80331a94>] 0x80331a94
[ 0.200000] [<8033e484>] 0x8033e484
[ 0.200000] [<8033ffdc>] 0x8033ffdc
[ 0.210000] [<8000c03c>] 0x8000c03c
[ 0.210000] [<80330000>] 0x80330000
[ 0.210000] [<80340000>] 0x80340000
[ 0.220000] [<8003eedc>] 0x8003eedc
[ 0.220000] [<80340000>] 0x80340000
[ 0.220000] [<801bd2a8>] 0x801bd2a8
[ 0.230000] [<8032fc4c>] 0x8032fc4c
[ 0.230000] [<802b0000>] 0x802b0000
[ 0.230000] [<8032f248>] 0x8032f248
[ 0.240000] [<80006abc>] 0x80006abc
[ 0.240000] [<80006acc>] 0x80006acc
[ 0.240000] [<80007b80>] 0x80007b80
[ 0.250000] [<80006abc>] 0x80006abc
[ 0.250000] [<800020a8>] 0x800020a8
[ 0.250000]
[ 0.250000] ---[ end trace 9686247e605d8ec8 ]---
[ 0.260000] ADM8668: applied USB workaround
[ 0.290000] PCI host bridge to bus 0000:00
[ 0.290000] pci_bus 0000:00: root bus resource [mem 0x16000000-0x1dffffff]
[ 0.300000] pci_bus 0000:00: root bus resource [io 0x12600000-0x127fffff]
[ 0.300000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 0.310000] PCI: fixing up ADM8668 controller
[ 0.310000] pci 0000:00:01.0: BAR 0: assigned [mem 0x16000000-0x16007fff]
[ 0.320000] Switched to clocksource MIPS
[ 0.330000] NET: Registered protocol family 2
[ 0.340000] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.340000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.350000] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.350000] TCP: reno registered
[ 0.360000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.360000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.370000] NET: Registered protocol family 1
[ 0.380000] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.390000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.390000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.410000] msgmni has been set to 119
[ 0.410000] io scheduler noop registered
[ 0.410000] io scheduler deadline registered (default)
[ 0.420000] Serial: AMBA driver
[ 0.420000] apb:uart0: ttyS0 at MMIO 0x1e400000 (irq = 6, base_baud = 0JJ́a AMBA
[ 0.430000] console [ttyS0] enabled
[ 0.430000] console [ttyS0] enabled
[ 0.440000] bootconsole [early0] disabled
[ 0.440000] bootconsole [early0] disabled
[ 0.450000] adm8668-nor: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x0022cb
[ 0.460000] Amd/Fujitsu Extended Query Table at 0x0040
[ 0.470000] Amd/Fujitsu Extended Query version 1.1.
[ 0.470000] number of CFI chips: 1
[ 0.480000] adm8668-nor: Couldn't find root filesystem
[ 0.570000] Creating 3 MTD partitions on "adm8668-nor":
[ 0.580000] 0x000000040000-0x000000800000 : "linux"
[ 0.590000] 0x0000000e0000-0x000000220000 : "rootfs"
[ 0.600000] mtd: device 1 (rootfs) set to be root filesystem
[ 0.610000] mtdsplit: no squashfs found in "rootfs"
[ 0.610000] mtdsplit: no squashfs found in "adm8668-nor"
[ 0.620000] 0x000000020000-0x000000040000 : "uboot_env"
[ 0.630000] net eth0: tulip_platform (Infineon ADM8668) at MMIO 0x11a00000 00:1e:e5:b1:98:fa, IRQ 7
[ 0.650000] net eth1: tulip_platform (Infineon ADM8668) at MMIO 0x11600000 00:1e:e5:b1:98:fb, IRQ 8
[ 0.660000] TCP: cubic registered
[ 0.660000] NET: Registered protocol family 17
[ 0.670000] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[ 0.680000] Bridge firewalling registered
[ 0.680000] 8021q: 802.1Q VLAN Support v1.8
[ 0.720000] List of all partitions:
[ 0.730000] 1f00 7936 mtdblock0 (driver?)
[ 0.730000] 1f01 1280 mtdblock1 (driver?)
[ 0.740000] 1f02 128 mtdblock2 (driver?)
[ 0.740000] No filesystem could mount root, tried: squashfs
[ 0.750000] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(31,1)
[ 0.750000] ---[ end Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(31,1)

Add Comment

Modify Ticket

Action
as assigned .
Author


E-mail address and user name can be saved in the Preferences.

 
Note: See TracTickets for help on using tickets.