Modify

Opened 3 years ago

Closed 2 years ago

#19877 closed defect (fixed)

Netgear WNR2200 with 15.05-rc1 - after every reboot an other WLAN BSSID

Reported by: anonymous Owned by: developers
Priority: high Milestone:
Component: base system Version: Trunk
Keywords: Cc:

Description

I need the WNR2200 for WDS-Master. Its fully unusable when the BSSID change at every reboot.

Attachments (0)

Change History (5)

comment:1 Changed 3 years ago by anonymous

Thanks to jow, this is a temporary fix:
uci set wireless.@wifi-iface[0].macaddr=00:11:22:33:44:55; uci commit wireless; wifi up

comment:2 Changed 3 years ago by anonymous

jow asked for dmesg:

dmesg
[ 0.000000] Linux version 3.18.11 (buildbot@builder1) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r45556) ) #1 Tue May 19 01:34:36 CEST 2015
[ 0.000000] MyLoader: sysp=ffffffff, boardp=ffffffff, parts=ffffffff
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 00019374 (MIPS 24Kc)
[ 0.000000] SoC: Atheros AR7241 rev 1
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x00000000-0x03ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x03ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x00000000-0x03ffffff]
[ 0.000000] On node 0 totalpages: 16384
[ 0.000000] free_area_init_node: node 0, pgdat 803822b0, node_mem_map 81000000
[ 0.000000] Normal zone: 128 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 16384 pages, LIFO batch:3
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
[ 0.000000] Kernel command line: board=WNR2200 console=ttyS0,115200 mtdparts=spi0.0:256k(u-boot)ro,64k(u-boot-env)ro,7808k(firmware),64k(art)ro rootfstype=squashfs,jffs2 noinitrd
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 60812K/65536K available (2626K kernel code, 132K rwdata, 544K rodata, 208K init, 194K bss, 4724K reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:51
[ 0.000000] Clocks: CPU:360.000MHz, DDR:360.000MHz, AHB:180.000MHz, Ref:5.000MHz
[ 0.000000] Calibrating delay loop... 239.61 BogoMIPS (lpj=1198080)
[ 0.070000] pid_max: default: 32768 minimum: 301
[ 0.070000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.080000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.090000] NET: Registered protocol family 16
[ 0.090000] MIPS: machine is NETGEAR WNR2200
[ 0.540000] registering PCI controller with io_map_base unset
[ 0.580000] PCI host bridge to bus 0000:00
[ 0.590000] pci_bus 0000:00: root bus resource [mem 0x10000000-0x13ffffff]
[ 0.600000] pci_bus 0000:00: root bus resource [io 0x0000]
[ 0.600000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 0.610000] pci 0000:00:00.0: [168c:002e] type 00 class 0x028000
[ 0.610000] pci 0000:00:00.0: fixup device configuration
[ 0.610000] pci 0000:00:00.0: reg 0x10: [mem 0x10000000-0x1000ffff 64bit]
[ 0.610000] pci 0000:00:00.0: supports D1
[ 0.610000] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[ 0.610000] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
[ 0.610000] pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x1000ffff 64bit]
[ 0.620000] pci 0000:00:00.0: using irq 40 for pin 1
[ 0.620000] Switched to clocksource MIPS
[ 0.630000] NET: Registered protocol family 2
[ 0.630000] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.630000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.640000] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.650000] TCP: reno registered
[ 0.650000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.660000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.660000] NET: Registered protocol family 1
[ 0.670000] PCI: CLS 0 bytes, default 32
[ 0.670000] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.690000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.690000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.700000] msgmni has been set to 118
[ 0.710000] io scheduler noop registered
[ 0.710000] io scheduler deadline registered (default)
[ 0.720000] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.730000] console [ttyS0] disabled
[ 0.750000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11, base_baud = 11250000) is a 16550A
[ 0.760000] console [ttyS0] enabled
[ 0.770000] bootconsole [early0] disabled
[ 0.780000] m25p80 spi0.0: found mx25l6405d, expected m25p80
[ 0.780000] m25p80 spi0.0: mx25l6405d (8192 Kbytes)
[ 0.790000] 4 cmdlinepart partitions found on MTD device spi0.0
[ 0.790000] Creating 4 MTD partitions on "spi0.0":
[ 0.800000] 0x000000000000-0x000000040000 : "u-boot"
[ 0.800000] 0x000000040000-0x000000050000 : "u-boot-env"
[ 0.810000] 0x000000050000-0x0000007f0000 : "firmware"
[ 0.830000] 2 netgear-fw partitions found on MTD device firmware
[ 0.830000] 0x000000050000-0x000000175440 : "kernel"
[ 0.840000] 0x000000175440-0x0000007f0000 : "rootfs"
[ 0.850000] mtd: device 4 (rootfs) set to be root filesystem
[ 0.850000] 1 squashfs-split partitions found on MTD device rootfs
[ 0.860000] 0x0000003b0000-0x0000007f0000 : "rootfs_data"
[ 0.860000] 0x0000007f0000-0x000000800000 : "art"
[ 0.910000] libphy: ag71xx_mdio: probed
[ 1.500000] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.1:04 [uid=004dd041, driver=Generic PHY]
[ 1.510000] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:MII
[ 2.100000] ag71xx-mdio.1: Found an AR7240/AR9330 built-in switch
[ 2.140000] eth1: Atheros AG71xx at 0xba000000, irq 5, mode:GMII
[ 2.150000] platform leds-gpio: Driver leds-gpio requests probe deferral
[ 2.160000] TCP: cubic registered
[ 2.160000] NET: Registered protocol family 17
[ 2.160000] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[ 2.180000] Bridge firewalling registered
[ 2.180000] 8021q: 802.1Q VLAN Support v1.8
[ 2.190000] platform leds-gpio: Driver leds-gpio requests probe deferral
[ 2.210000] VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
[ 2.220000] Freeing unused kernel memory: 208K (8039c000 - 803d0000)
[ 3.630000] init: failed to symlink /tmp -> /var
[ 3.640000] init: Console is alive
[ 3.640000] init: - watchdog -
[ 5.360000] usbcore: registered new interface driver usbfs
[ 5.370000] usbcore: registered new interface driver hub
[ 5.370000] usbcore: registered new device driver usb
[ 5.390000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 5.400000] ehci-platform: EHCI generic platform driver
[ 5.400000] ehci-platform ehci-platform: EHCI Host Controller
[ 5.410000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
[ 5.420000] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
[ 5.440000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
[ 5.440000] hub 1-0:1.0: USB hub found
[ 5.450000] hub 1-0:1.0: 1 port detected
[ 5.450000] platform leds-gpio: Driver leds-gpio requests probe deferral
[ 5.470000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 5.480000] ohci-platform: OHCI generic platform driver
[ 5.660000] init: - preinit -
[ 6.490000] random: mktemp urandom read with 10 bits of entropy available
[ 8.030000] eth1: link up (1000Mbps/Full duplex)
[ 9.920000] jffs2: notice: (407) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (0 unchecked, 0 orphan) and 1 of xref (0 dead, 0 orphan) found.
[ 9.930000] mount_root: switching to jffs2 overlay
[ 9.990000] eth1: link down
[ 10.010000] procd: - early -
[ 10.010000] procd: - watchdog -
[ 10.740000] procd: - ubus -
[ 11.750000] procd: - init -
[ 12.810000] NET: Registered protocol family 10
[ 12.830000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 12.850000] Loading modules backported from Linux version master-2015-03-09-0-g141f155
[ 12.860000] Backport generated by backports.git backports-20150129-0-gdd4a670
[ 12.870000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 12.890000] nf_conntrack version 0.5.0 (953 buckets, 3812 max)
[ 12.950000] xt_time: kernel timezone is -0000
[ 12.990000] cfg80211: Calling CRDA to update world regulatory domain
[ 13.020000] cfg80211: World regulatory domain updated:
[ 13.020000] cfg80211: DFS Master region: unset
[ 13.030000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[ 13.040000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 13.040000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 13.050000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[ 13.060000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[ 13.070000] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s)
[ 13.080000] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[ 13.090000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[ 13.090000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[ 13.200000] PPP generic driver version 2.4.2
[ 13.200000] NET: Registered protocol family 24
[ 13.270000] PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
[ 13.280000] ath: phy0: eeprom contains invalid mac address: ff:ff:ff:ff:ff:ff
[ 13.290000] ath: phy0: random mac address will be used: 7e:11:ac:c8:6d:f0
[ 13.300000] ath: EEPROM regdomain: 0x0
[ 13.300000] ath: EEPROM indicates default country code should be used
[ 13.300000] ath: doing EEPROM country->regdmn map search
[ 13.300000] ath: country maps to regdmn code: 0x3a
[ 13.300000] ath: Country alpha2 being used: US
[ 13.300000] ath: Regpair used: 0x3a
[ 13.310000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 13.320000] ieee80211 phy0: Atheros AR9287 Rev:2 mem=0xb0000000, irq=40
[ 13.330000] platform leds-gpio: Driver leds-gpio requests probe deferral
[ 13.340000] cfg80211: Calling CRDA for country: US
[ 13.340000] cfg80211: Regulatory domain changed to country: US
[ 13.350000] cfg80211: DFS Master region: FCC
[ 13.350000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[ 13.360000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 3000 mBm), (N/A)
[ 13.370000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 1700 mBm), (N/A)
[ 13.380000] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2300 mBm), (0 s)
[ 13.390000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 3000 mBm), (N/A)
[ 13.400000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4000 mBm), (N/A)
[ 24.910000] device eth1 entered promiscuous mode
[ 24.930000] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 24.980000] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 26.570000] eth1: link up (1000Mbps/Full duplex)
[ 26.570000] br-lan: port 1(eth1) entered forwarding state
[ 26.580000] br-lan: port 1(eth1) entered forwarding state
[ 26.590000] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 27.400000] eth0: link up (100Mbps/Full duplex)
[ 27.400000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 27.680000] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 27.740000] device wlan0 entered promiscuous mode
[ 27.750000] br-lan: port 2(wlan0) entered forwarding state
[ 27.750000] br-lan: port 2(wlan0) entered forwarding state
[ 28.580000] br-lan: port 1(eth1) entered forwarding state
[ 28.860000] br-lan: port 2(wlan0) entered disabled state
[ 30.220000] pppoe-wan: renamed from ppp0
[ 31.000000] br-lan: port 2(wlan0) entered forwarding state
[ 31.000000] br-lan: port 2(wlan0) entered forwarding state
[ 31.010000] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 33.000000] br-lan: port 2(wlan0) entered forwarding state
[ 55.330000] random: nonblocking pool is initialized
[ 135.200000] eth1: link down
[ 135.200000] br-lan: port 1(eth1) entered disabled state
[ 209.920000] device wlan0.sta1 entered promiscuous mode
[ 209.930000] br-lan: port 3(wlan0.sta1) entered forwarding state
[ 209.930000] br-lan: port 3(wlan0.sta1) entered forwarding state
[ 211.930000] br-lan: port 3(wlan0.sta1) entered forwarding state
[ 234.200000] eth1: link up (1000Mbps/Full duplex)
[ 234.200000] br-lan: port 1(eth1) entered forwarding state
[ 234.210000] br-lan: port 1(eth1) entered forwarding state
[ 236.210000] br-lan: port 1(eth1) entered forwarding state
[ 280.410000] nf_conntrack: automatic helper assignment is deprecated and it will be removed soon. Use the iptables CT target to attach helpers instead.

comment:3 Changed 3 years ago by anonymous

I have same problem on a complete new WNR2200 bought yesterday and freshly installed OpenWrt. No dd-wrt or something like that before.

comment:5 Changed 2 years ago by nbd

  • Resolution set to fixed
  • Status changed from new to closed

fixed in r47873

Add Comment

Modify Ticket

Action
as closed .
The resolution will be deleted. Next status will be 'reopened'.
Author


E-mail address and user name can be saved in the Preferences.

 
Note: See TracTickets for help on using tickets.