Modify

Opened 3 years ago

Closed 2 years ago

#19167 closed defect (fixed)

ath10k firmware crashed after r44655

Reported by: gcyscm Owned by: developers
Priority: normal Milestone: Chaos Calmer 15.05
Component: kernel Version: Trunk
Keywords: Cc:

Description

[ 25.040000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[ 25.050000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 3000 mBm), (N/A)
[ 25.060000] cfg80211: (5270000 KHz - 5330000 KHz @ 40000 KHz), (N/A, 1700 mBm), (0 s)
[ 25.070000] cfg80211: (5490000 KHz - 5590000 KHz @ 80000 KHz), (N/A, 3000 mBm), (0 s)
[ 25.080000] cfg80211: (5650000 KHz - 5710000 KHz @ 40000 KHz), (N/A, 3000 mBm), (0 s)
[ 25.080000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 3000 mBm), (N/A)
[ 25.670000] eth0: link up (1000Mbps/Full duplex)
[ 25.670000] br-lan: port 1(eth0) entered forwarding state
[ 25.680000] br-lan: port 1(eth0) entered forwarding state
[ 26.420000] eth1: link up (100Mbps/Full duplex)
[ 27.680000] br-lan: port 1(eth0) entered forwarding state
[ 28.200000] ath10k_pci 0000:00:00.0: otp stream is empty, using board.bin contents
[ 30.390000] pppoe-wan: renamed from ppp0
[ 30.450000] device wlan0 entered promiscuous mode
[ 30.530000] device wlan1 entered promiscuous mode
[ 30.530000] br-lan: port 3(wlan1) entered forwarding state
[ 30.540000] br-lan: port 3(wlan1) entered forwarding state
[ 31.400000] br-lan: port 3(wlan1) entered disabled state
[ 31.510000] br-lan: port 3(wlan1) entered forwarding state
[ 31.510000] br-lan: port 3(wlan1) entered forwarding state
[ 33.510000] br-lan: port 3(wlan1) entered forwarding state
[ 33.590000] br-lan: port 2(wlan0) entered forwarding state
[ 33.600000] br-lan: port 2(wlan0) entered forwarding state
[ 34.020000] ath10k_pci 0000:00:00.0: firmware crashed! (uuid ba433228-96f6-4a42-9db4-21adc0528f79)
[ 34.030000] ath10k_pci 0000:00:00.0: qca988x hw2.0 (0x4100016c, 0x043222ff) fw 10.2.4.45 api 4 htt 2.1 wmi 5 cal otp max_sta 128
[ 34.040000] ath10k_pci 0000:00:00.0: debug 0 debugfs 1 tracing 0 dfs 1 testmode 1
[ 34.060000] ath10k_pci 0000:00:00.0: failed to read diag value at 0x10100804: -16
[ 34.070000] ath10k_pci 0000:00:00.0: failed to get memcpy hi address for firmware address 4: -16
[ 34.080000] ath10k_pci 0000:00:00.0: failed to read firmware dump area: -16
[ 34.180000] ieee80211 phy0: Hardware restart was requested
[ 34.180000] ath10k_pci 0000:00:00.0: failed to to request monitor vdev 1 stop: -143
[ 34.190000] ath10k_pci 0000:00:00.0: failed to synchronize monitor vdev 1 stop: -143
[ 34.200000] ath10k_pci 0000:00:00.0: failed to stop monitor vdev: -143
[ 34.430000] ath10k_pci 0000:00:00.0: failed to read diag value at 0x10100800: -16
[ 34.440000] ath10k_pci 0000:00:00.0: failed to poke copy engine: -16
[ 34.560000] ath10k_pci 0000:00:00.0: failed to read diag value at 0x10100800: -16
[ 34.570000] ath10k_pci 0000:00:00.0: failed to poke copy engine: -16
[ 35.600000] br-lan: port 2(wlan0) entered forwarding state
[ 36.860000] ath10k_pci 0000:00:00.0: device successfully recovered
[ 37.200000] ath10k_pci 0000:00:00.0: firmware crashed! (uuid cc53fd38-a6b1-41e1-9d76-819d19103f07)
[ 37.210000] ath10k_pci 0000:00:00.0: qca988x hw2.0 (0x4100016c, 0x043222ff) fw 10.2.4.45 api 4 htt 2.1 wmi 5 cal otp max_sta 128
[ 37.220000] ath10k_pci 0000:00:00.0: debug 0 debugfs 1 tracing 0 dfs 1 testmode 1
[ 37.240000] ath10k_pci 0000:00:00.0: failed to read firmware dump area: -16
[ 37.350000] ieee80211 phy0: Hardware restart was requested
[ 39.970000] ath10k_pci 0000:00:00.0: device successfully recovered
[ 40.440000] ath10k_pci 0000:00:00.0: firmware crashed! (uuid e9c5a12b-c0c5-4da7-809b-5995d3ffa25a)
[ 40.450000] ath10k_pci 0000:00:00.0: qca988x hw2.0 (0x4100016c, 0x043222ff) fw 10.2.4.45 api 4 htt 2.1 wmi 5 cal otp max_sta 128
[ 40.460000] ath10k_pci 0000:00:00.0: debug 0 debugfs 1 tracing 0 dfs 1 testmode 1
[ 40.480000] ath10k_warn: 15 callbacks suppressed
[ 40.490000] ath10k_pci 0000:00:00.0: failed to read diag value at 0x10100804: -16
[ 40.490000] ath10k_pci 0000:00:00.0: failed to get memcpy hi address for firmware address 4: -16
[ 40.500000] ath10k_pci 0000:00:00.0: failed to read firmware dump area: -16
[ 40.680000] ieee80211 phy0: Hardware restart was requested
[ 40.680000] ath10k_pci 0000:00:00.0: failed to to request monitor vdev 1 stop: -143
[ 40.690000] ath10k_pci 0000:00:00.0: failed to synchronize monitor vdev 1 stop: -143
[ 40.700000] ath10k_pci 0000:00:00.0: failed to stop monitor vdev: -143
[ 40.920000] ath10k_pci 0000:00:00.0: failed to read diag value at 0x10100800: -16
[ 40.930000] ath10k_pci 0000:00:00.0: failed to poke copy engine: -16
[ 41.060000] ath10k_pci 0000:00:00.0: failed to read diag value at 0x10100800: -16
[ 41.070000] ath10k_pci 0000:00:00.0: failed to poke copy engine: -16
[ 41.260000] ath10k_pci 0000:00:00.0: failed to read diag value at 0x10100800: -16
[ 43.650000] ath10k_pci 0000:00:00.0: device successfully recovered
[ 43.940000] random: nonblocking pool is initialized
[ 44.010000] ath10k_pci 0000:00:00.0: firmware crashed! (uuid d1b2ec10-5a3b-4d71-b4cd-aca93a1b4547)
[ 44.020000] ath10k_pci 0000:00:00.0: qca988x hw2.0 (0x4100016c, 0x043222ff) fw 10.2.4.45 api 4 htt 2.1 wmi 5 cal otp max_sta 128
[ 44.030000] ath10k_pci 0000:00:00.0: debug 0 debugfs 1 tracing 0 dfs 1 testmode 1
[ 44.050000] ath10k_pci 0000:00:00.0: failed to read firmware dump area: -16
[ 44.160000] ieee80211 phy0: Hardware restart was requested
[ 47.150000] ath10k_pci 0000:00:00.0: device successfully recovered
[ 47.530000] ath10k_pci 0000:00:00.0: firmware crashed! (uuid dc710121-4db4-4ae4-91a1-94f0b6531886)
[ 47.540000] ath10k_pci 0000:00:00.0: qca988x hw2.0 (0x4100016c, 0x043222ff) fw 10.2.4.45 api 4 htt 2.1 wmi 5 cal otp max_sta 128
[ 47.550000] ath10k_pci 0000:00:00.0: debug 0 debugfs 1 tracing 0 dfs 1 testmode 1
[ 47.570000] ath10k_warn: 14 callbacks suppressed
[ 47.580000] ath10k_pci 0000:00:00.0: failed to read diag value at 0x10100804: -16
[ 47.580000] ath10k_pci 0000:00:00.0: failed to get memcpy hi address for firmware address 4: -16
[ 47.590000] ath10k_pci 0000:00:00.0: failed to read firmware dump area: -16
[ 47.700000] ieee80211 phy0: Hardware restart was requested
[ 47.700000] ath10k_pci 0000:00:00.0: failed to to request monitor vdev 1 stop: -143
[ 47.710000] ath10k_pci 0000:00:00.0: failed to synchronize monitor vdev 1 stop: -143
[ 47.720000] ath10k_pci 0000:00:00.0: failed to stop monitor vdev: -143
[ 47.940000] ath10k_pci 0000:00:00.0: failed to read diag value at 0x10100800: -16
[ 47.950000] ath10k_pci 0000:00:00.0: failed to poke copy engine: -16
[ 48.060000] ath10k_pci 0000:00:00.0: failed to read diag value at 0x10100800: -16
[ 48.070000] ath10k_pci 0000:00:00.0: failed to poke copy engine: -16
[ 48.180000] ath10k_pci 0000:00:00.0: failed to read diag value at 0x10100800: -16
[ 50.370000] ath10k_pci 0000:00:00.0: device successfully recovered
[ 50.730000] ath10k_pci 0000:00:00.0: firmware crashed! (uuid 3aa511ea-25cd-4f5d-bcba-985c7b52b244)
[ 50.740000] ath10k_pci 0000:00:00.0: qca988x hw2.0 (0x4100016c, 0x043222ff) fw 10.2.4.45 api 4 htt 2.1 wmi 5 cal otp max_sta 128
[ 50.750000] ath10k_pci 0000:00:00.0: debug 0 debugfs 1 tracing 0 dfs 1 testmode 1
[ 50.770000] ath10k_pci 0000:00:00.0: failed to read firmware dump area: -16
[ 50.880000] ieee80211 phy0: Hardware restart was requested
[ 53.490000] ath10k_pci 0000:00:00.0: device successfully recovered
[ 53.870000] ath10k_pci 0000:00:00.0: firmware crashed! (uuid 7020cc3a-6be9-4a51-9b73-73ba422b16a2)
[ 53.880000] ath10k_pci 0000:00:00.0: qca988x hw2.0 (0x4100016c, 0x043222ff) fw 10.2.4.45 api 4 htt 2.1 wmi 5 cal otp max_sta 128
[ 53.890000] ath10k_pci 0000:00:00.0: debug 0 debugfs 1 tracing 0 dfs 1 testmode 1
[ 53.910000] ath10k_warn: 14 callbacks suppressed
[ 53.920000] ath10k_pci 0000:00:00.0: failed to read diag value at 0x10100804: -16
[ 53.920000] ath10k_pci 0000:00:00.0: failed to get memcpy hi address for firmware address 4: -16
[ 53.930000] ath10k_pci 0000:00:00.0: failed to read firmware dump area: -16
[ 54.040000] ieee80211 phy0: Hardware restart was requested
[ 54.040000] ath10k_pci 0000:00:00.0: failed to to request monitor vdev 1 stop: -143
[ 54.050000] ath10k_pci 0000:00:00.0: failed to synchronize monitor vdev 1 stop: -143
[ 54.060000] ath10k_pci 0000:00:00.0: failed to stop monitor vdev: -143
[ 54.280000] ath10k_pci 0000:00:00.0: failed to read diag value at 0x10100800: -16
[ 54.290000] ath10k_pci 0000:00:00.0: failed to poke copy engine: -16
[ 54.400000] ath10k_pci 0000:00:00.0: failed to read diag value at 0x10100800: -16
[ 54.410000] ath10k_pci 0000:00:00.0: failed to poke copy engine: -16
[ 54.520000] ath10k_pci 0000:00:00.0: failed to read diag value at 0x10100800: -16
[ 56.710000] ath10k_pci 0000:00:00.0: device successfully recovered
[ 57.090000] ath10k_pci 0000:00:00.0: firmware crashed! (uuid 92170570-5b3e-44c3-8921-3535e28e3b17)
[ 57.100000] ath10k_pci 0000:00:00.0: qca988x hw2.0 (0x4100016c, 0x043222ff) fw 10.2.4.45 api 4 htt 2.1 wmi 5 cal otp max_sta 128
[ 57.110000] ath10k_pci 0000:00:00.0: debug 0 debugfs 1 tracing 0 dfs 1 testmode 1
[ 57.130000] ath10k_pci 0000:00:00.0: failed to read firmware dump area: -16
[ 57.240000] ieee80211 phy0: Hardware restart was requested
[ 59.850000] ath10k_pci 0000:00:00.0: device successfully recovered
[ 60.230000] ath10k_pci 0000:00:00.0: firmware crashed! (uuid 9aba74da-8779-4203-8f99-d9c80dbba96e)
[ 60.240000] ath10k_pci 0000:00:00.0: qca988x hw2.0 (0x4100016c, 0x043222ff) fw 10.2.4.45 api 4 htt 2.1 wmi 5 cal otp max_sta 128
[ 60.250000] ath10k_pci 0000:00:00.0: debug 0 debugfs 1 tracing 0 dfs 1 testmode 1
[ 60.270000] ath10k_warn: 14 callbacks suppressed
[ 60.280000] ath10k_pci 0000:00:00.0: failed to read diag value at 0x10100804: -16
[ 60.290000] ath10k_pci 0000:00:00.0: failed to get memcpy hi address for firmware address 4: -16
[ 60.290000] ath10k_pci 0000:00:00.0: failed to read firmware dump area: -16
[ 60.400000] ieee80211 phy0: Hardware restart was requested
[ 60.400000] ath10k_pci 0000:00:00.0: failed to to request monitor vdev 1 stop: -143
[ 60.410000] ath10k_pci 0000:00:00.0: failed to synchronize monitor vdev 1 stop: -143
[ 60.420000] ath10k_pci 0000:00:00.0: failed to stop monitor vdev: -143
[ 60.640000] ath10k_pci 0000:00:00.0: failed to read diag value at 0x10100800: -16
[ 60.650000] ath10k_pci 0000:00:00.0: failed to poke copy engine: -16
[ 60.760000] ath10k_pci 0000:00:00.0: failed to read diag value at 0x10100800: -16
[ 60.770000] ath10k_pci 0000:00:00.0: failed to poke copy engine: -16
[ 60.880000] ath10k_pci 0000:00:00.0: failed to read diag value at 0x10100800: -16
[ 63.070000] ath10k_pci 0000:00:00.0: device successfully recovered
[ 63.450000] ath10k_pci 0000:00:00.0: firmware crashed! (uuid cb8661d8-f087-43fb-9f65-e153ab8f13f5)
[ 63.460000] ath10k_pci 0000:00:00.0: qca988x hw2.0 (0x4100016c, 0x043222ff) fw 10.2.4.45 api 4 htt 2.1 wmi 5 cal otp max_sta 128
[ 63.470000] ath10k_pci 0000:00:00.0: debug 0 debugfs 1 tracing 0 dfs 1 testmode 1
[ 63.490000] ath10k_pci 0000:00:00.0: failed to read firmware dump area: -16
[ 63.600000] ieee80211 phy0: Hardware restart was requested
[ 66.210000] ath10k_pci 0000:00:00.0: device successfully recovered
[ 66.590000] ath10k_pci 0000:00:00.0: firmware crashed! (uuid c14c52c7-4eaf-48ca-a146-573ed466dbda)
[ 66.600000] ath10k_pci 0000:00:00.0: qca988x hw2.0 (0x4100016c, 0x043222ff) fw 10.2.4.45 api 4 htt 2.1 wmi 5 cal otp max_sta 128
[ 66.610000] ath10k_pci 0000:00:00.0: debug 0 debugfs 1 tracing 0 dfs 1 testmode 1
[ 66.630000] ath10k_warn: 14 callbacks suppressed
[ 66.640000] ath10k_pci 0000:00:00.0: failed to read diag value at 0x10100804: -16
[ 66.640000] ath10k_pci 0000:00:00.0: failed to get memcpy hi address for firmware address 4: -16
[ 66.650000] ath10k_pci 0000:00:00.0: failed to read firmware dump area: -16
[ 66.760000] ieee80211 phy0: Hardware restart was requested
[ 66.760000] ath10k_pci 0000:00:00.0: failed to to request monitor vdev 1 stop: -143
[ 66.770000] ath10k_pci 0000:00:00.0: failed to synchronize monitor vdev 1 stop: -143

Attachments (0)

Change History (14)

comment:1 Changed 3 years ago by anonymous

Probably same issue as /ticket/19161.html

There was alot of wifi related commit yesterday, chances are one have broken wifi. I bet it will be fix today

comment:2 Changed 3 years ago by anonymous

crash (r44655-r44953-r.....)
Make dirclean&rebuild @r44953, it's also crashed when I enabled 5GHz wifi.
r44654 is OK

My router is Mercury MAC1200R, AR9344+AR9882, 8M ROM+64M RAM

This is syslog @r44953:

Mon Mar 23 17:58:34 2015 daemon.info dnsmasq[1346]: DNS service limited to local subnets
Mon Mar 23 17:58:34 2015 daemon.info dnsmasq-dhcp[1346]: DHCP, IP range 192.168.1.100 -- 192.168.1.249, lease time 12h
Mon Mar 23 17:58:34 2015 daemon.info dnsmasq[1346]: using local addresses only for domain lan
Mon Mar 23 17:58:34 2015 daemon.warn dnsmasq[1346]: no servers found in /tmp/resolv.conf.auto, will retry
Mon Mar 23 17:58:34 2015 daemon.info dnsmasq[1346]: read /etc/hosts - 1 addresses
Mon Mar 23 17:58:34 2015 daemon.info dnsmasq[1346]: read /tmp/hosts/dhcp - 1 addresses
Mon Mar 23 17:58:34 2015 daemon.info dnsmasq[1346]: read /tmp/hosts/odhcpd - 1 addresses
Mon Mar 23 17:58:34 2015 daemon.info dnsmasq-dhcp[1346]: read /etc/ethers - 0 addresses
Mon Mar 23 17:58:35 2015 daemon.info procd: - init complete -
Mon Mar 23 17:58:35 2015 daemon.notice vnstatd[1361]: vnStat daemon 1.12 started. (uid:0 gid:0)
Mon Mar 23 17:58:35 2015 daemon.notice vnstatd[1361]: Monitoring: br-lan (100 Mbit) eth1 (100 Mbit)
Mon Mar 23 17:58:40 2015 daemon.info dnsmasq-dhcp[1346]: DHCPREQUEST(br-lan) 192.168.1.137 00:e0:4c:01:e3:b1
Mon Mar 23 17:58:40 2015 daemon.info dnsmasq-dhcp[1346]: DHCPACK(br-lan) 192.168.1.137 00:e0:4c:01:e3:b1 GC-PC
Mon Mar 23 17:58:44 2015 daemon.info dnsmasq-dhcp[1346]: DHCPINFORM(br-lan) 192.168.1.137 00:e0:4c:01:e3:b1
Mon Mar 23 17:58:44 2015 daemon.info dnsmasq-dhcp[1346]: DHCPACK(br-lan) 192.168.1.137 00:e0:4c:01:e3:b1 GC-PC
Mon Mar 23 17:59:11 2015 kern.notice kernel: [ 67.330000] random: nonblocking pool is initialized
Mon Mar 23 18:00:02 2015 kern.warn kernel: [ 118.220000] ath10k_pci 0000:00:00.0: otp stream is empty, using board.bin contents
Mon Mar 23 18:00:03 2015 kern.info kernel: [ 119.270000] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
Mon Mar 23 18:00:03 2015 kern.info kernel: [ 119.290000] device wlan0 entered promiscuous mode
Mon Mar 23 18:00:06 2015 kern.info kernel: [ 121.660000] br-lan: port 2(wlan0) entered forwarding state
Mon Mar 23 18:00:06 2015 kern.info kernel: [ 121.660000] br-lan: port 2(wlan0) entered forwarding state
Mon Mar 23 18:00:06 2015 kern.info kernel: [ 121.670000] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
Mon Mar 23 18:00:06 2015 daemon.notice netifd: Network device 'wlan0' link is up
Mon Mar 23 18:00:06 2015 kern.err kernel: [ 122.090000] ath10k_pci 0000:00:00.0: firmware crashed! (uuid 9254ac14-a9b8-45d2-b168-8e8844502f1b)
Mon Mar 23 18:00:06 2015 kern.info kernel: [ 122.100000] ath10k_pci 0000:00:00.0: qca988x hw2.0 (0x4100016c, 0x043222ff) fw 10.2.4.45 api 4 htt 2.1 wmi 5 cal otp max_sta 128
Mon Mar 23 18:00:06 2015 kern.info kernel: [ 122.110000] ath10k_pci 0000:00:00.0: debug 0 debugfs 1 tracing 0 dfs 1 testmode 1
Mon Mar 23 18:00:06 2015 kern.warn kernel: [ 122.130000] ath10k_pci 0000:00:00.0: failed to read diag value at 0x10100804: -16
Mon Mar 23 18:00:06 2015 kern.warn kernel: [ 122.130000] ath10k_pci 0000:00:00.0: failed to get memcpy hi address for firmware address 4: -16
Mon Mar 23 18:00:06 2015 kern.err kernel: [ 122.140000] ath10k_pci 0000:00:00.0: failed to read firmware dump area: -16
Mon Mar 23 18:00:06 2015 kern.info kernel: [ 122.250000] ieee80211 phy0: Hardware restart was requested
Mon Mar 23 18:00:06 2015 kern.warn kernel: [ 122.250000] ath10k_pci 0000:00:00.0: failed to put down monitor vdev 1: -143
Mon Mar 23 18:00:06 2015 kern.warn kernel: [ 122.260000] ath10k_pci 0000:00:00.0: failed to to request monitor vdev 1 stop: -143
Mon Mar 23 18:00:06 2015 kern.warn kernel: [ 122.270000] ath10k_pci 0000:00:00.0: failed to synchronize monitor vdev 1 stop: -143
Mon Mar 23 18:00:06 2015 kern.warn kernel: [ 122.280000] ath10k_pci 0000:00:00.0: failed to stop monitor vdev: -143
Mon Mar 23 18:00:07 2015 kern.warn kernel: [ 122.490000] ath10k_pci 0000:00:00.0: failed to read diag value at 0x10100800: -16
Mon Mar 23 18:00:07 2015 kern.warn kernel: [ 122.500000] ath10k_pci 0000:00:00.0: failed to poke copy engine: -16
Mon Mar 23 18:00:07 2015 kern.warn kernel: [ 122.610000] ath10k_pci 0000:00:00.0: failed to read diag value at 0x10100800: -16
Mon Mar 23 18:00:08 2015 kern.info kernel: [ 123.660000] br-lan: port 2(wlan0) entered forwarding state
Mon Mar 23 18:00:10 2015 kern.info kernel: [ 125.920000] ath10k_pci 0000:00:00.0: device successfully recovered
Mon Mar 23 18:00:10 2015 kern.err kernel: [ 126.380000] ath10k_pci 0000:00:00.0: firmware crashed! (uuid 4a69ecc7-299e-47ad-a71f-468b08430c3e)
Mon Mar 23 18:00:10 2015 kern.info kernel: [ 126.390000] ath10k_pci 0000:00:00.0: qca988x hw2.0 (0x4100016c, 0x043222ff) fw 10.2.4.45 api 4 htt 2.1 wmi 5 cal otp max_sta 128
Mon Mar 23 18:00:10 2015 kern.info kernel: [ 126.400000] ath10k_pci 0000:00:00.0: debug 0 debugfs 1 tracing 0 dfs 1 testmode 1
Mon Mar 23 18:00:10 2015 kern.err kernel: [ 126.420000] ath10k_pci 0000:00:00.0: failed to read firmware dump area: -16
Mon Mar 23 18:00:11 2015 kern.info kernel: [ 126.530000] ieee80211 phy0: Hardware restart was requested
Mon Mar 23 18:00:11 2015 kern.warn kernel: [ 127.230000] ath10k_warn: 15 callbacks suppressed
Mon Mar 23 18:00:11 2015 kern.warn kernel: [ 127.230000] ath10k_pci 0000:00:00.0: otp stream is empty, using board.bin contents
Mon Mar 23 18:00:14 2015 kern.info kernel: [ 129.710000] ath10k_pci 0000:00:00.0: device successfully recovered
Mon Mar 23 18:00:14 2015 kern.err kernel: [ 130.080000] ath10k_pci 0000:00:00.0: firmware crashed! (uuid 29835b75-5119-41cd-b454-66520e6318ad)
Mon Mar 23 18:00:14 2015 kern.info kernel: [ 130.090000] ath10k_pci 0000:00:00.0: qca988x hw2.0 (0x4100016c, 0x043222ff) fw 10.2.4.45 api 4 htt 2.1 wmi 5 cal otp max_sta 128
Mon Mar 23 18:00:14 2015 kern.info kernel: [ 130.100000] ath10k_pci 0000:00:00.0: debug 0 debugfs 1 tracing 0 dfs 1 testmode 1
Mon Mar 23 18:00:14 2015 kern.warn kernel: [ 130.120000] ath10k_pci 0000:00:00.0: failed to read diag value at 0x10100804: -16
Mon Mar 23 18:00:14 2015 kern.warn kernel: [ 130.130000] ath10k_pci 0000:00:00.0: failed to get memcpy hi address for firmware address 4: -16
Mon Mar 23 18:00:14 2015 kern.err kernel: [ 130.140000] ath10k_pci 0000:00:00.0: failed to read firmware dump area: -16
Mon Mar 23 18:00:14 2015 kern.info kernel: [ 130.250000] ieee80211 phy0: Hardware restart was requested
Mon Mar 23 18:00:14 2015 kern.warn kernel: [ 130.250000] ath10k_pci 0000:00:00.0: failed to put down monitor vdev 1: -143
Mon Mar 23 18:00:14 2015 kern.warn kernel: [ 130.260000] ath10k_pci 0000:00:00.0: failed to to request monitor vdev 1 stop: -143
Mon Mar 23 18:00:14 2015 kern.warn kernel: [ 130.270000] ath10k_pci 0000:00:00.0: failed to synchronize monitor vdev 1 stop: -143
Mon Mar 23 18:00:14 2015 kern.warn kernel: [ 130.280000] ath10k_pci 0000:00:00.0: failed to stop monitor vdev: -143
Mon Mar 23 18:00:15 2015 kern.warn kernel: [ 130.490000] ath10k_pci 0000:00:00.0: failed to read diag value at 0x10100800: -16
Mon Mar 23 18:00:15 2015 kern.warn kernel: [ 130.500000] ath10k_pci 0000:00:00.0: failed to poke copy engine: -16
Mon Mar 23 18:00:15 2015 kern.warn kernel: [ 130.610000] ath10k_pci 0000:00:00.0: failed to read diag value at 0x10100800: -16
Mon Mar 23 18:00:17 2015 kern.info kernel: [ 132.910000] ath10k_pci 0000:00:00.0: device successfully recovered
Mon Mar 23 18:00:17 2015 kern.err kernel: [ 133.200000] ath10k_pci 0000:00:00.0: firmware crashed! (uuid bbffa271-b7aa-4452-9a7d-9599a5a2c266)
Mon Mar 23 18:00:17 2015 kern.info kernel: [ 133.200000] ath10k_pci 0000:00:00.0: qca988x hw2.0 (0x4100016c, 0x043222ff) fw 10.2.4.45 api 4 htt 2.1 wmi 5 cal otp max_sta 128
Mon Mar 23 18:00:17 2015 kern.info kernel: [ 133.220000] ath10k_pci 0000:00:00.0: debug 0 debugfs 1 tracing 0 dfs 1 testmode 1
Mon Mar 23 18:00:17 2015 kern.err kernel: [ 133.240000] ath10k_pci 0000:00:00.0: failed to read firmware dump area: -16
Mon Mar 23 18:00:17 2015 kern.info kernel: [ 133.340000] ieee80211 phy0: Hardware restart was requested
Mon Mar 23 18:00:20 2015 kern.info kernel: [ 135.950000] ath10k_pci 0000:00:00.0: device successfully recovered
Mon Mar 23 18:00:20 2015 kern.err kernel: [ 136.330000] ath10k_pci 0000:00:00.0: firmware crashed! (uuid d6f6729f-8855-444a-b7a4-13b9de7f393e)
Mon Mar 23 18:00:20 2015 kern.info kernel: [ 136.340000] ath10k_pci 0000:00:00.0: qca988x hw2.0 (0x4100016c, 0x043222ff) fw 10.2.4.45 api 4 htt 2.1 wmi 5 cal otp max_sta 128
Mon Mar 23 18:00:20 2015 kern.info kernel: [ 136.350000] ath10k_pci 0000:00:00.0: debug 0 debugfs 1 tracing 0 dfs 1 testmode 1
Mon Mar 23 18:00:20 2015 kern.warn kernel: [ 136.370000] ath10k_warn: 16 callbacks suppressed
Mon Mar 23 18:00:20 2015 kern.warn kernel: [ 136.370000] ath10k_pci 0000:00:00.0: failed to read diag value at 0x10100804: -16
Mon Mar 23 18:00:20 2015 kern.warn kernel: [ 136.380000] ath10k_pci 0000:00:00.0: failed to get memcpy hi address for firmware address 4: -16
Mon Mar 23 18:00:20 2015 kern.err kernel: [ 136.390000] ath10k_pci 0000:00:00.0: failed to read firmware dump area: -16
Mon Mar 23 18:00:21 2015 kern.info kernel: [ 136.500000] ieee80211 phy0: Hardware restart was requested
Mon Mar 23 18:00:21 2015 kern.warn kernel: [ 136.500000] ath10k_pci 0000:00:00.0: failed to to request monitor vdev 1 stop: -143
Mon Mar 23 18:00:21 2015 kern.warn kernel: [ 136.510000] ath10k_pci 0000:00:00.0: failed to synchronize monitor vdev 1 stop: -143
Mon Mar 23 18:00:21 2015 kern.warn kernel: [ 136.520000] ath10k_pci 0000:00:00.0: failed to stop monitor vdev: -143
Mon Mar 23 18:00:21 2015 kern.warn kernel: [ 136.730000] ath10k_pci 0000:00:00.0: failed to read diag value at 0x10100800: -16
Mon Mar 23 18:00:21 2015 kern.warn kernel: [ 136.740000] ath10k_pci 0000:00:00.0: failed to poke copy engine: -16
Mon Mar 23 18:00:21 2015 kern.warn kernel: [ 136.850000] ath10k_pci 0000:00:00.0: failed to read diag value at 0x10100800: -16
Mon Mar 23 18:00:21 2015 kern.warn kernel: [ 136.860000] ath10k_pci 0000:00:00.0: failed to poke copy engine: -16
Mon Mar 23 18:00:21 2015 kern.warn kernel: [ 136.970000] ath10k_pci 0000:00:00.0: failed to read diag value at 0x10100800: -16
Mon Mar 23 18:00:23 2015 kern.info kernel: [ 139.220000] ath10k_pci 0000:00:00.0: device successfully recovered
Mon Mar 23 18:00:24 2015 kern.err kernel: [ 139.600000] ath10k_pci 0000:00:00.0: firmware crashed! (uuid 52f1dec5-54ca-4418-b51c-c97a93ebaebb)
Mon Mar 23 18:00:24 2015 kern.info kernel: [ 139.610000] ath10k_pci 0000:00:00.0: qca988x hw2.0 (0x4100016c, 0x043222ff) fw 10.2.4.45 api 4 htt 2.1 wmi 5 cal otp max_sta 128
Mon Mar 23 18:00:24 2015 kern.info kernel: [ 139.620000] ath10k_pci 0000:00:00.0: debug 0 debugfs 1 tracing 0 dfs 1 testmode 1
Mon Mar 23 18:00:24 2015 kern.err kernel: [ 139.640000] ath10k_pci 0000:00:00.0: failed to read firmware dump area: -16
Mon Mar 23 18:00:24 2015 kern.info kernel: [ 139.750000] ieee80211 phy0: Hardware restart was requested
Mon Mar 23 18:00:26 2015 kern.info kernel: [ 142.360000] ath10k_pci 0000:00:00.0: device successfully recovered

comment:3 Changed 3 years ago by anonymous

I'm hitting this too, with r45365.

comment:4 Changed 3 years ago by exkernel

ath10k doesn't work, with r45340, Mercury MAC1200R

comment:5 Changed 3 years ago by exkernel

ath10k doesn't work, with r45340, Mercury MAC1200R

comment:6 Changed 3 years ago by anonymous

Same with 15.05-rc1

comment:7 Changed 3 years ago by anonymous

I am also getting this issue on a mac1200r. I bet this is mac1200r specified? Rollback the firmware to old version seems good to me https://github.com/kvalo/ath10k-firmware/tree/master/10.1

comment:8 Changed 3 years ago by anonymous

With the latest fw of the ones listed on the page above, the ath10k comes up as a
working WLAN-device.

thnx for posting

comment:9 Changed 3 years ago by anonymous

Same with 15.05-rc2

comment:10 Changed 3 years ago by anonymous

Could someone please try again with these two patches and firmware v5: https://lists.openwrt.org/pipermail/openwrt-devel/2015-June/033827.html

comment:11 Changed 3 years ago by draplater

ath10k doesn't work, with r46174, Qihoo C301.

comment:12 Changed 3 years ago by anonymous

I have just reported this to the ath10k developers: http://lists.infradead.org/pipermail/ath10k/2015-July/005624.html

comment:13 Changed 2 years ago by anonymous

Please try again with r46900 (trunk) or r46901 (CC).
Felix pushed a patch which should solve this issue.

comment:14 Changed 2 years ago by rmilecki

  • Resolution set to fixed
  • Status changed from new to closed

It seems xdarklight (IRC) was also affected by this issue and he confirms the fix:

[20:11] <xdarklight> nbd: could you (or any other OpenWrt developer) please close this ticket: https://dev.openwrt.org/ticket/19167
[20:11] <xdarklight> the two commits mentioned in the last comment really fixed this bug

Add Comment

Modify Ticket

Action
as closed .
The resolution will be deleted. Next status will be 'reopened'.
Author


E-mail address and user name can be saved in the Preferences.

 
Note: See TracTickets for help on using tickets.