Modify

Opened 3 years ago

Closed 3 years ago

#17747 closed defect (duplicate)

ar9341 tl-wr8410 wireless driver bug:ath: phy0: Failed to stop TX DMA, queues=0x004

Reported by: weeds Owned by: developers
Priority: high Milestone: Barrier Breaker 14.07
Component: kernel Version: Barrier Breaker 14.07
Keywords: Cc:

Description

when run under some network pressure, it will occur below dmesg, which show "ath: phy0: Failed to stop TX DMA, queues=0x004", could anyone explain this ? I think something not right at here.


dmesg
[ 0.000000] Linux version 3.10.49 (weeds@weeds-Lenovo) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r13) ) #6 Tue Sep 2 04:13:38 EDT 2014
[ 0.000000] MyLoader: sysp=f243d70d, boardp=068823f6, parts=db57ce78
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU revision is: 0001974c (MIPS 74Kc)
[ 0.000000] SoC: Atheros AR9341 rev 1
[ 0.000000] Clocks: CPU:535.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:25.000MHz
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x00000000-0x03ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x03ffffff]
[ 0.000000] On node 0 totalpages: 16384
[ 0.000000] free_area_init_node: node 0, pgdat 803129b0, node_mem_map 81000000
[ 0.000000] Normal zone: 128 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 16384 pages, LIFO batch:3
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
[ 0.000000] Kernel command line: board=TL-WR841N-v8 console=ttyS0,115200 rootfstype=squashfs,jffs2 noinitrd
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 61208k/65536k available (2251k kernel code, 4328k reserved, 598k data, 284k init, 0k highmem)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:51
[ 0.070000] Calibrating delay loop... 266.64 BogoMIPS (lpj=1333248)
[ 0.080000] pid_max: default: 32768 minimum: 301
[ 0.080000] Mount-cache hash table entries: 512
[ 0.090000] NET: Registered protocol family 16
[ 0.090000] MIPS: machine is TP-LINK TL-WR841N/ND v8
[ 0.510000] bio: create slab <bio-0> at 0
[ 0.510000] Switching to clocksource MIPS
[ 0.520000] NET: Registered protocol family 2
[ 0.520000] TCP established hash table entries: 512 (order: 0, 4096 bytes)
[ 0.530000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)
[ 0.540000] TCP: Hash tables configured (established 512 bind 512)
[ 0.540000] TCP: reno registered
[ 0.540000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.550000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.560000] NET: Registered protocol family 1
[ 0.560000] PCI: CLS 0 bytes, default 32
[ 0.580000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.580000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.590000] msgmni has been set to 119
[ 0.600000] io scheduler noop registered
[ 0.600000] io scheduler deadline registered (default)
[ 0.610000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[ 0.630000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A
[ 0.640000] console [ttyS0] enabled, bootconsole disabled
[ 0.650000] ath79-spi ath79-spi: master is unqueued, this is deprecated
[ 0.660000] m25p80 spi0.0: found mx25l6405d, expected m25p80
[ 0.670000] m25p80 spi0.0: mx25l6405d (8192 Kbytes)
[ 0.670000] 5 tp-link partitions found on MTD device spi0.0
[ 0.680000] Creating 5 MTD partitions on "spi0.0":
[ 0.680000] 0x000000000000-0x000000020000 : "u-boot"
[ 0.690000] 0x000000020000-0x00000012042c : "kernel"
[ 0.700000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 0.710000] 0x00000012042c-0x0000007f0000 : "rootfs"
[ 0.720000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 0.730000] mtd: device 2 (rootfs) set to be root filesystem
[ 0.740000] 1 squashfs-split partitions found on MTD device rootfs
[ 0.740000] 0x000000430000-0x0000007f0000 : "rootfs_data"
[ 0.750000] 0x0000007f0000-0x000000800000 : "art"
[ 0.760000] 0x000000020000-0x0000007f0000 : "firmware"
[ 0.780000] libphy: ag71xx_mdio: probed
[ 1.340000] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.1:04 [uid=004dd042, driver=Generic PHY]
[ 1.350000] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:MII
[ 1.900000] ag71xx-mdio.1: Found an AR934X built-in switch
[ 2.940000] eth1: Atheros AG71xx at 0xba000000, irq 5, mode:GMII
[ 2.950000] TCP: cubic registered
[ 2.950000] NET: Registered protocol family 17
[ 2.960000] 8021q: 802.1Q VLAN Support v1.8
[ 2.970000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[ 2.970000] Freeing unused kernel memory: 284K (80329000 - 80370000)
[ 7.900000] eth1: link up (1000Mbps/Full duplex)
[ 10.110000] jffs2_scan_eraseblock(): End of filesystem marker found at 0x10000
[ 10.110000] jffs2_build_filesystem(): unlocking the mtd device... done.
[ 10.120000] jffs2_build_filesystem(): erasing all blocks after the end marker... done.
[ 33.870000] jffs2: notice: (302) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[ 34.230000] eth1: link down
[ 36.150000] NET: Registered protocol family 10
[ 36.180000] nf_conntrack version 0.5.0 (960 buckets, 3840 max)
[ 36.190000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 36.220000] u32 classifier
[ 36.220000] input device check on
[ 36.230000] Actions configured
[ 36.240000] Mirror/redirect action on
[ 36.260000] Failed to load ipt action
[ 36.320000] Loading modules backported from Linux version master-2014-05-22-0-gf2032ea
[ 36.320000] Backport generated by backports.git backports-20140320-37-g5c33da0
[ 36.350000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 36.500000] xt_time: kernel timezone is -0000
[ 36.580000] cfg80211: Calling CRDA to update world regulatory domain
[ 36.600000] cfg80211: World regulatory domain updated:
[ 36.610000] cfg80211: DFS Master region: unset
[ 36.610000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[ 36.620000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 36.630000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 36.640000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[ 36.650000] cfg80211: (5170000 KHz - 5250000 KHz @ 160000 KHz), (N/A, 2000 mBm), (N/A)
[ 36.660000] cfg80211: (5250000 KHz - 5330000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[ 36.670000] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[ 36.670000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[ 36.680000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[ 36.720000] PPP generic driver version 2.4.2
[ 36.740000] NET: Registered protocol family 24
[ 36.820000] ath: EEPROM regdomain: 0x0
[ 36.820000] ath: EEPROM indicates default country code should be used
[ 36.820000] ath: doing EEPROM country->regdmn map search
[ 36.820000] ath: country maps to regdmn code: 0x3a
[ 36.820000] ath: Country alpha2 being used: US
[ 36.820000] ath: Regpair used: 0x3a
[ 36.830000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 36.850000] ieee80211 phy0: Atheros AR9340 Rev:0 mem=0xb8100000, irq=47
[ 36.870000] cfg80211: Calling CRDA for country: US
[ 36.870000] cfg80211: Regulatory domain changed to country: US
[ 36.880000] cfg80211: DFS Master region: FCC
[ 36.880000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[ 36.890000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 3000 mBm), (N/A)
[ 36.900000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 1700 mBm), (N/A)
[ 36.910000] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz), (N/A, 2300 mBm), (0 s)
[ 36.920000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 3000 mBm), (N/A)
[ 36.930000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4000 mBm), (N/A)
[ 42.020000] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 44.210000] eth1: link up (1000Mbps/Full duplex)
[ 44.210000] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[ 48.070000] eth1: link down
[ 49.140000] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 49.160000] IPv6: ADDRCONF(NETDEV_UP): eth1.1: link is not ready
[ 49.160000] device eth1.1 entered promiscuous mode
[ 49.170000] device eth1 entered promiscuous mode
[ 49.170000] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 49.230000] IPv6: ADDRCONF(NETDEV_UP): eth1.2: link is not ready
[ 49.230000] device eth1.2 entered promiscuous mode
[ 49.340000] IPv6: ADDRCONF(NETDEV_UP): br-lan2: link is not ready
[ 49.380000] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 49.740000] eth1: link up (1000Mbps/Full duplex)
[ 49.740000] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[ 49.870000] br-lan: port 1(eth1.1) entered forwarding state
[ 49.870000] br-lan: port 1(eth1.1) entered forwarding state
[ 49.880000] IPv6: ADDRCONF(NETDEV_CHANGE): eth1.1: link becomes ready
[ 49.880000] br-lan2: port 1(eth1.2) entered forwarding state
[ 49.890000] br-lan2: port 1(eth1.2) entered forwarding state
[ 49.900000] IPv6: ADDRCONF(NETDEV_CHANGE): eth1.2: link becomes ready
[ 49.900000] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan2: link becomes ready
[ 49.910000] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 51.610000] eth0: link up (10Mbps/Half duplex)
[ 51.610000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 51.870000] br-lan: port 1(eth1.1) entered forwarding state
[ 51.890000] br-lan2: port 1(eth1.2) entered forwarding state
[ 53.380000] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 53.430000] device wlan0 entered promiscuous mode
[ 60.220000] device wlan0-1 entered promiscuous mode
[ 60.230000] br-lan2: port 2(wlan0-1) entered forwarding state
[ 60.230000] br-lan2: port 2(wlan0-1) entered forwarding state
[ 60.240000] IPv6: ADDRCONF(NETDEV_UP): wlan0-1: link is not ready
[ 60.450000] br-lan: port 2(wlan0) entered forwarding state
[ 60.450000] br-lan: port 2(wlan0) entered forwarding state
[ 60.460000] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 60.460000] br-lan2: port 2(wlan0-1) entered disabled state
[ 61.580000] br-lan2: port 2(wlan0-1) entered forwarding state
[ 61.580000] br-lan2: port 2(wlan0-1) entered forwarding state
[ 61.590000] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0-1: link becomes ready
[ 62.450000] br-lan: port 2(wlan0) entered forwarding state
[ 63.580000] br-lan2: port 2(wlan0-1) entered forwarding state
[ 115.170000] raw_sendmsg: wifidog forgot to set AF_INET. Fix it!
[ 351.130000] HTB: quantum of class 10001 is big. Consider r2q change.
[ 351.160000] HTB: quantum of class 11024 is big. Consider r2q change.
[ 422.640000] eth1: link down
[ 422.640000] br-lan: port 1(eth1.1) entered disabled state
[ 422.640000] br-lan2: port 1(eth1.2) entered disabled state
[ 2602.390000] ath: phy0: Failed to stop TX DMA, queues=0x100!
[ 2611.220000] ath: phy0: Failed to stop TX DMA, queues=0x001!
[ 2611.320000] ath: phy0: Failed to stop TX DMA, queues=0x001!
[ 2638.590000] ath: phy0: Failed to stop TX DMA, queues=0x004!
[ 2644.030000] ath: phy0: Failed to stop TX DMA, queues=0x005!
[ 2659.240000] ath: phy0: Failed to stop TX DMA, queues=0x001!
[ 2660.080000] ath: phy0: Failed to stop TX DMA, queues=0x001!
[ 9184.720000] ath: phy0: Failed to stop TX DMA, queues=0x004!
[51915.190000] eth1: link up (1000Mbps/Full duplex)
[51915.190000] br-lan: port 1(eth1.1) entered forwarding state
[51915.200000] br-lan: port 1(eth1.1) entered forwarding state
[51915.200000] br-lan2: port 1(eth1.2) entered forwarding state
[51915.210000] br-lan2: port 1(eth1.2) entered forwarding state
[51917.200000] br-lan: port 1(eth1.1) entered forwarding state
[51917.210000] br-lan2: port 1(eth1.2) entered forwarding state
[59221.340000] ath: phy0: Failed to stop TX DMA, queues=0x004!
[69821.550000] ath: phy0: Failed to stop TX DMA, queues=0x005!
[69822.370000] ath: phy0: Failed to stop TX DMA, queues=0x005!
[69828.830000] ath: phy0: Failed to stop TX DMA, queues=0x004!
[69852.180000] ath: phy0: Failed to stop TX DMA, queues=0x004!
[69853.000000] ath: phy0: Failed to stop TX DMA, queues=0x004!
[69854.960000] ath: phy0: Failed to stop TX DMA, queues=0x004!
[69859.880000] ath: phy0: Failed to stop TX DMA, queues=0x004!
[69860.870000] ath: phy0: Failed to stop TX DMA, queues=0x005!
[69861.840000] ath: phy0: Failed to stop TX DMA, queues=0x004!
[69863.340000] ath: phy0: Failed to stop TX DMA, queues=0x005!
[69889.870000] ath: phy0: Failed to stop TX DMA, queues=0x004!
[69922.830000] ath: phy0: Failed to stop TX DMA, queues=0x004!
[69955.470000] ath: phy0: Failed to stop TX DMA, queues=0x005!
[69987.250000] ath: phy0: Failed to stop TX DMA, queues=0x004!

Attachments (0)

Change History (1)

comment:1 Changed 3 years ago by nbd

  • Resolution set to duplicate
  • Status changed from new to closed

Add Comment

Modify Ticket

Action
as closed .
The resolution will be deleted. Next status will be 'reopened'.
Author


E-mail address and user name can be saved in the Preferences.

 
Note: See TracTickets for help on using tickets.