Modify

Opened 3 years ago

Last modified 22 months ago

#17619 assigned defect

Sunxi A20 banana pi Ethernet issue.

Reported by: viljar.rooda@… Owned by: wigyori
Priority: normal Milestone: Bugs Paradise
Component: base system Version: Barrier Breaker 14.07
Keywords: Cc:

Description

Tryed both Offical snapshot under /snapshots/trunk/sunxi/
or building my own buildroot result same issue:

root@OpenWrt:/# ifconfig eth0 up
[   45.316822] eth0: device MAC address 7e:1d:a6:62:9c:67
[   45.423002] stmmac_hw_setup: DMA engine initialization failed
[   45.428756] stmmac_open: Hw setup failed
ifconfig: SIOCSIFFLAGS: Device or resource busy

i have usb to Ethernet adapter that works but on board gigabit ethernet port fails.
full boot:

U-Boot SPL 2014.01-rc1-g599a7ea (Aug 19 2014 - 23:18:28)
Board: bananapi
DRAM: 1024 MiB
CPU: 960000000Hz, AXI/AHB/APB: 3/2/2
spl: not an uImage at 1600


U-Boot 2014.01-rc1-g599a7ea (Aug 19 2014 - 23:18:28) Allwinner Technology

CPU:   Allwinner A20 (SUN7I)
Board: bananapi
I2C:   ready
DRAM:  1 GiB
WARNING: Caches not enabled
MMC:   SUNXI SD/MMC: 0
*** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
Net:   mii0
Warning: failed to set MAC address

Hit any key to stop autoboot:  0
reading uEnv.txt
240 bytes read in 4 ms (58.6 KiB/s)
Loaded environment from uEnv.txt
Running uenvcmd ...
reading uImage
2544360 bytes read in 117 ms (20.7 MiB/s)
reading dtb
19498 bytes read in 6 ms (3.1 MiB/s)
## Booting kernel from Legacy Image at 46000000 ...
   Image Name:   ARM OpenWrt Linux-3.13.7
   Created:      2014-08-20   0:40:42 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    2544296 Bytes = 2.4 MiB
   Load Address: 40008000
   Entry Point:  40008000
   Verifying Checksum ... OK
## Flattened Device Tree blob at 49000000
   Booting using the fdt blob at 0x49000000
   Loading Kernel Image ... OK
   Using Device Tree in place at 49000000, end 49007c29

Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 3.13.7 (debi@debi) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r42220) ) #1 SMP PREEMPT Wed Aug 20 03:40:34 EEST 2014
[    0.000000] CPU: ARMv7 Processor [410fc074] revision 4 (ARMv7), cr=10c5387d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] Machine model: Lemaker bananaPi
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] psci: probing function IDs from device-tree
[    0.000000] PERCPU: Embedded 7 pages/cpu @c0d89000 s7040 r8192 d13440 u32768
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 260624
[    0.000000] Kernel command line: console=ttyS0,115200 earlyprintk rootwait root=/dev/mmcblk0p2
[    0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Memory: 1033844K/1048576K available (3603K kernel code, 159K rwdata, 1012K rodata, 186K init, 606K bss, 14732K reserved, 270336K highmem)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
[    0.000000]     vmalloc : 0xf0000000 - 0xff000000   ( 240 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xef800000   ( 760 MB)
[    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
[    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)
[    0.000000]       .text : 0xc0008000 - 0xc0489f44   (4616 kB)
[    0.000000]       .init : 0xc048a000 - 0xc04b8b80   ( 187 kB)
[    0.000000]       .data : 0xc04ba000 - 0xc04e1ef8   ( 160 kB)
[    0.000000]        .bss : 0xc04e1ef8 - 0xc0579aec   ( 607 kB)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000]  RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[    0.000000] NR_IRQS:16 nr_irqs:16 16
[    0.000000] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956969942ns
[    0.000000] sched_clock: 32 bits at 160MHz, resolution 6ns, wraps every 26843545593ns
[    0.000000] Console: colour dummy device 80x30
[    0.000195] Calibrating delay loop... 1915.28 BogoMIPS (lpj=9576448)
[    0.059904] pid_max: default: 32768 minimum: 301
[    0.060089] Mount-cache hash table entries: 512
[    0.065119] CPU: Testing write buffer coherency: ok
[    0.065466] /cpus/cpu@0 missing clock-frequency property
[    0.065486] /cpus/cpu@1 missing clock-frequency property
[    0.065499] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[    0.065530] Setting up static identity map for 0x40011938 - 0x4001196c
[    0.120595] CPU1: Booted secondary processor
[    0.180167] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[    0.180286] Brought up 2 CPUs
[    0.180308] SMP: Total of 2 processors activated.
[    0.180315] CPU: All CPU(s) started in HYP mode.
[    0.180320] CPU: Virtualization extensions available.
[    0.184856] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 4
[    0.185131] pinctrl core: initialized pinctrl subsystem
[    0.185467] regulator-dummy: no parameters
[    0.185779] NET: Registered protocol family 16
[    0.186077] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.193406] bio: create slab <bio-0> at 0
[    0.193913] reg-fixed-voltage ahci-5v.3: could not find pctldev for node /soc@01c00000/pinctrl@01c20800/ahci_pwr_pin@0, deferring probe
[    0.193941] platform ahci-5v.3: Driver reg-fixed-voltage requests probe deferral
[    0.193969] reg-fixed-voltage usb1-vbus.4: could not find pctldev for node /soc@01c00000/pinctrl@01c20800/usb1_vbus_pin@0, deferring probe
[    0.193985] platform usb1-vbus.4: Driver reg-fixed-voltage requests probe deferral
[    0.194008] reg-fixed-voltage usb2-vbus.5: could not find pctldev for node /soc@01c00000/pinctrl@01c20800/usb2_vbus_pin@0, deferring probe
[    0.194022] platform usb2-vbus.5: Driver reg-fixed-voltage requests probe deferral
[    0.194434] SCSI subsystem initialized
[    0.194846] usbcore: registered new interface driver usbfs
[    0.194906] usbcore: registered new interface driver hub
[    0.195008] usbcore: registered new device driver usb
[    0.195136] pps_core: LinuxPPS API ver. 1 registered
[    0.195145] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.195168] PTP clock support registered
[    0.195922] Switched to clocksource timer
[    0.200188] Clockevents: could not switch to one-shot mode:
[    0.200194] Clockevents: could not switch to one-shot mode: dummy_timer is not functional.
[    0.200209] Could not switch to high resolution mode on CPU 0
[    0.200221]  dummy_timer is not functional.
[    0.200228] Could not switch to high resolution mode on CPU 1
[    0.201466] NET: Registered protocol family 2
[    0.202347] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
[    0.202429] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[    0.202551] TCP: Hash tables configured (established 8192 bind 8192)
[    0.202633] TCP: reno registered
[    0.202650] UDP hash table entries: 512 (order: 2, 16384 bytes)
[    0.202706] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[    0.203028] NET: Registered protocol family 1
[    0.204196] audit: initializing netlink socket (disabled)
[    0.204245] type=2000 audit(0.190:1): initialized
[    0.204859] bounce pool size: 64 pages
[    0.210983] VFS: Disk quotas dquot_6.5.2
[    0.211250] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    0.212849] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.212861] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.213370] msgmni has been set to 1491
[    0.214121] io scheduler noop registered
[    0.214138] io scheduler deadline registered
[    0.214176] io scheduler cfq registered (default)
[    0.214434] platform 1c13400.phy: Driver sun4i-usb-phy requests probe deferral
[    0.216655] sunxi-pinctrl 1c20800.pinctrl: initialized sunXi PIO driver
[    0.249346] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[    0.272286] 1c28000.serial: ttyS0 at MMIO 0x1c28000 (irq = 33, base_baud = 1500000) is a U6_16550A
[    0.841468] console [ttyS0] enabled
[    0.866691] dw-apb-uart 1c29800.serial: Couldn't set LCR to 0
[    0.873436] dw-apb-uart 1c29800.serial: Couldn't set LCR to 0
[    0.879217] 1c29800.serial: ttyS1 at MMIO 0x1c29800 (irq = 51, base_baud = 1500000) is a U6_16550A
[    0.909947] dw-apb-uart 1c29c00.serial: Couldn't set LCR to 0
[    0.916693] dw-apb-uart 1c29c00.serial: Couldn't set LCR to 0
[    0.922470] 1c29c00.serial: ttyS2 at MMIO 0x1c29c00 (irq = 52, base_baud = 1500000) is a U6_16550A
[    0.932109] platform 1c18000.sata: Driver ahci-sunxi requests probe deferral
[    0.941597] stmmaceth 1c50000.ethernet: dummy supplies not allowed
[    0.947784] stmmaceth 1c50000.ethernet: no regulator found
[    0.953361] stmmaceth 1c50000.ethernet: no reset control found
[    0.959190]  Ring mode enabled
[    0.962259]  No HW DMA feature register supported
[    0.966783]  Normal descriptors
[    0.970104]  TX Checksum insertion supported
[    0.985968] libphy: stmmac: probed
[    0.989388] eth0: PHY ID 1fff1fff at 0 IRQ 0 (stmmac-0:00) active
[    0.995537] eth0: PHY ID 1fff1fff at 1 IRQ 0 (stmmac-0:01)
[    1.001041] eth0: PHY ID 1fff1fff at 2 IRQ 0 (stmmac-0:02)
[    1.006522] eth0: PHY ID 1fff1fff at 3 IRQ 0 (stmmac-0:03)
[    1.012046] eth0: PHY ID 1fff1fff at 4 IRQ 0 (stmmac-0:04)
[    1.017530] eth0: PHY ID 0fff0fff at 5 IRQ 0 (stmmac-0:05)
[    1.023038] eth0: PHY ID 0fff1fff at 6 IRQ 0 (stmmac-0:06)
[    1.028521] eth0: PHY ID 0fff0fff at 7 IRQ 0 (stmmac-0:07)
[    1.034014] eth0: PHY ID 07ff0fff at 8 IRQ 0 (stmmac-0:08)
[    1.039495] eth0: PHY ID 0fff0fff at 9 IRQ 0 (stmmac-0:09)
[    1.044999] eth0: PHY ID 0fff07ff at 10 IRQ 0 (stmmac-0:0a)
[    1.050584] eth0: PHY ID 07ff07ff at 11 IRQ 0 (stmmac-0:0b)
[    1.056151] eth0: PHY ID 07ff07ff at 12 IRQ 0 (stmmac-0:0c)
[    1.061734] eth0: PHY ID 03ff07ff at 13 IRQ 0 (stmmac-0:0d)
[    1.067302] eth0: PHY ID 07ff03ff at 14 IRQ 0 (stmmac-0:0e)
[    1.072880] eth0: PHY ID 03ff07ff at 15 IRQ 0 (stmmac-0:0f)
[    1.078447] eth0: PHY ID 03ff03ff at 16 IRQ 0 (stmmac-0:10)
[    1.084024] eth0: PHY ID 03ff03ff at 17 IRQ 0 (stmmac-0:11)
[    1.089594] eth0: PHY ID 03ff01ff at 18 IRQ 0 (stmmac-0:12)
[    1.095170] eth0: PHY ID 01ff03ff at 19 IRQ 0 (stmmac-0:13)
[    1.100747] eth0: PHY ID 01ff01ff at 20 IRQ 0 (stmmac-0:14)
[    1.106315] eth0: PHY ID 01ff01ff at 21 IRQ 0 (stmmac-0:15)
[    1.111890] eth0: PHY ID 01ff01ff at 22 IRQ 0 (stmmac-0:16)
[    1.117456] eth0: PHY ID 01ff00ff at 23 IRQ 0 (stmmac-0:17)
[    1.123033] eth0: PHY ID 00ff01ff at 24 IRQ 0 (stmmac-0:18)
[    1.128600] eth0: PHY ID 01ff01ff at 25 IRQ 0 (stmmac-0:19)
[    1.134179] eth0: PHY ID 01ff00ff at 26 IRQ 0 (stmmac-0:1a)
[    1.139749] eth0: PHY ID 00ff00ff at 27 IRQ 0 (stmmac-0:1b)
[    1.145331] eth0: PHY ID 00ff01ff at 28 IRQ 0 (stmmac-0:1c)
[    1.150910] eth0: PHY ID 007f00ff at 29 IRQ 0 (stmmac-0:1d)
[    1.156478] eth0: PHY ID 007f007f at 30 IRQ 0 (stmmac-0:1e)
[    1.162084] eth0: PHY ID 00ff007f at 31 IRQ 0 (stmmac-0:1f)
[    1.167768] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.174315] ehci-platform: EHCI generic platform driver
[    1.179694] platform 1c14000.usb: Driver ehci-platform requests probe deferral
[    1.187014] platform 1c1c000.usb: Driver ehci-platform requests probe deferral
[    1.194401] usbcore: registered new interface driver usb-storage
[    1.200631] mousedev: PS/2 mouse device common for all mice
[    1.206542] input: 1c22800.lradc as /devices/soc.2/1c22800.lradc/input/input0
[    1.215131] sunxi-wdt 1c20c90.watchdog: Watchdog enabled (timeout=16 sec, nowayout=0)
[    1.223438] sunxi-mmc 1c0f000.mmc: dummy supplies not allowed
[    1.229634] sunxi-mmc 1c0f000.mmc: Got CD GPIO #234.
[    1.234817] sunxi-mmc 1c0f000.mmc: base:0xf00fa000 irq:64
[    1.240958] TCP: cubic registered
[    1.244275] Initializing XFRM netlink socket
[    1.248566] NET: Registered protocol family 17
[    1.253187] Bridge firewalling registered
[    1.257210] 8021q: 802.1Q VLAN Support v1.8
[    1.261537] Registering SWP/SWPB emulation handler
[    1.266652] registered taskstats version 1
[    1.271458] ahci-5v: 5000 mV
[    1.274794] usb1-vbus: 5000 mV
[    1.278215] usb2-vbus: 5000 mV
[    1.350159] ahci-sunxi 1c18000.sata: controller can't do PMP, turning off CAP_PMP
[    1.357649] ahci-sunxi 1c18000.sata: forcing PORTS_IMPL to 0x1
[    1.363538] ahci-sunxi 1c18000.sata: AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl platform mode
[    1.372504] ahci-sunxi 1c18000.sata: flags: ncq sntf pm led clo only pio slum part ccc
[    1.381261] scsi0 : ahci_platform
[    1.384874] ata1: SATA max UDMA/133 mmio [mem 0x01c18000-0x01c18fff] port 0x100 irq 88
[    1.393101] ehci-platform 1c14000.usb: EHCI Host Controller
[    1.398699] ehci-platform 1c14000.usb: new USB bus registered, assigned bus number 1
[    1.406566] ehci-platform 1c14000.usb: irq 71, io mem 0x01c14000
[    1.430153] ehci-platform 1c14000.usb: USB 2.0 started, EHCI 1.00
[    1.436436] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    1.443229] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.450451] usb usb1: Product: EHCI Host Controller
[    1.455325] usb usb1: Manufacturer: Linux 3.13.7 ehci_hcd
[    1.460723] usb usb1: SerialNumber: 1c14000.usb
[    1.465712] hub 1-0:1.0: USB hub found
[    1.469500] hub 1-0:1.0: 1 port detected
[    1.473898] ehci-platform 1c1c000.usb: EHCI Host Controller
[    1.479487] ehci-platform 1c1c000.usb: new USB bus registered, assigned bus number 2
[    1.487335] ehci-platform 1c1c000.usb: irq 72, io mem 0x01c1c000
[    1.510160] ehci-platform 1c1c000.usb: USB 2.0 started, EHCI 1.00
[    1.516445] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[    1.523240] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.530460] usb usb2: Product: EHCI Host Controller
[    1.535334] usb usb2: Manufacturer: Linux 3.13.7 ehci_hcd
[    1.540733] usb usb2: SerialNumber: 1c1c000.usb
[    1.545699] hub 2-0:1.0: USB hub found
[    1.549480] hub 2-0:1.0: 1 port detected
[    1.553730] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[    1.647719] mmc0: host does not support reading read-only switch. assuming write-enable.
[    1.740160] ata1: SATA link down (SStatus 0 SControl 300)
[    1.760256] Waiting for root device /dev/mmcblk0p2...
[    1.840155] mmc0: new high speed SDHC card at address 0007
[    1.846036] isa bounce pool size: 16 pages
[    1.850308] mmcblk0: mmc0:0007 SD8GB 7.42 GiB
[    1.856528]  mmcblk0: p1 p2
[    1.870214] usb 2-1: new high-speed USB device number 2 using ehci-platform
[    1.871818] EXT4-fs (mmcblk0p2): couldn't mount as ext3 due to feature incompatibilities
[    1.872975] EXT4-fs (mmcblk0p2): couldn't mount as ext2 due to feature incompatibilities
[    1.897309] EXT4-fs (mmcblk0p2): mounted filesystem without journal. Opts: (null)
[    1.904908] VFS: Mounted root (ext4 filesystem) readonly on device 179:2.
[    1.911958] Freeing unused kernel memory: 184K (c048a000 - c04b8000)
[    2.053521] usb 2-1: New USB device found, idVendor=0b95, idProduct=7720
[    2.060242] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[    2.067371] usb 2-1: Product: AX88x72A
[    2.071123] usb 2-1: Manufacturer: ASIX Elec. Corp.
[    2.075996] usb 2-1: SerialNumber: B0F07C
[    2.267898] sunxi-mmc 1c0f000.mmc: smc 0 err, cmd 18, RD DTO !!
[    2.273854] sunxi-mmc 1c0f000.mmc: data error, sending stop command
[    2.280197] mmcblk0: timed out sending r/w cmd command, card status 0x900
[    2.286988] end_request: I/O error, dev mmcblk0, sector 81976
[    2.292759] end_request: I/O error, dev mmcblk0, sector 81984
[    2.298504] end_request: I/O error, dev mmcblk0, sector 81992
[    2.304257] end_request: I/O error, dev mmcblk0, sector 82000
[    2.310001] end_request: I/O error, dev mmcblk0, sector 82008
[    2.315753] end_request: I/O error, dev mmcblk0, sector 82016
[    2.321503] end_request: I/O error, dev mmcblk0, sector 82024
[    2.327246] end_request: I/O error, dev mmcblk0, sector 82032
[    2.332995] end_request: I/O error, dev mmcblk0, sector 82040
[    2.338739] end_request: I/O error, dev mmcblk0, sector 82048
[    2.680123] sunxi-mmc 1c0f000.mmc: smc 0 err, cmd 18, RD DTO !!
[    2.686052] sunxi-mmc 1c0f000.mmc: data error, sending stop command
[    2.692373] mmcblk0: timed out sending r/w cmd command, card status 0x900
[    2.699185] EXT4-fs error (device mmcblk0p2): ext4_find_entry:1309: inode #3011: comm swapper/0: reading directory lblock 0

U-Boot SPL 2014.01-rc1-g599a7ea (Aug 19 2014 - 23:18:28)
Board: bananapi
DRAM: 1024 MiB
CPU: 960000000Hz, AXI/AHB/APB: 3/2/2
spl: not an uImage at 1600


U-Boot 2014.01-rc1-g599a7ea (Aug 19 2014 - 23:18:28) Allwinner Technology

CPU:   Allwinner A20 (SUN7I)
Board: bananapi
I2C:   ready
DRAM:  1 GiB
WARNING: Caches not enabled
MMC:   SUNXI SD/MMC: 0
*** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
Net:   mii0
Warning: failed to set MAC address

Hit any key to stop autoboot:  0
reading uEnv.txt
240 bytes read in 4 ms (58.6 KiB/s)
Loaded environment from uEnv.txt
Running uenvcmd ...
reading uImage
2544360 bytes read in 117 ms (20.7 MiB/s)
reading dtb
19498 bytes read in 7 ms (2.7 MiB/s)
## Booting kernel from Legacy Image at 46000000 ...
   Image Name:   ARM OpenWrt Linux-3.13.7
   Created:      2014-08-20   0:40:42 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    2544296 Bytes = 2.4 MiB
   Load Address: 40008000
   Entry Point:  40008000
   Verifying Checksum ... OK
## Flattened Device Tree blob at 49000000
   Booting using the fdt blob at 0x49000000
   Loading Kernel Image ... OK
   Using Device Tree in place at 49000000, end 49007c29

Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 3.13.7 (debi@debi) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r42220) ) #1 SMP PREEMPT Wed Aug 20 03:40:34 EEST 2014
[    0.000000] CPU: ARMv7 Processor [410fc074] revision 4 (ARMv7), cr=10c5387d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] Machine model: Lemaker bananaPi
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] psci: probing function IDs from device-tree
[    0.000000] PERCPU: Embedded 7 pages/cpu @c0d89000 s7040 r8192 d13440 u32768
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 260624
[    0.000000] Kernel command line: console=ttyS0,115200 earlyprintk rootwait root=/dev/mmcblk0p2
[    0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Memory: 1033844K/1048576K available (3603K kernel code, 159K rwdata, 1012K rodata, 186K init, 606K bss, 14732K reserved, 270336K highmem)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
[    0.000000]     vmalloc : 0xf0000000 - 0xff000000   ( 240 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xef800000   ( 760 MB)
[    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
[    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)
[    0.000000]       .text : 0xc0008000 - 0xc0489f44   (4616 kB)
[    0.000000]       .init : 0xc048a000 - 0xc04b8b80   ( 187 kB)
[    0.000000]       .data : 0xc04ba000 - 0xc04e1ef8   ( 160 kB)
[    0.000000]        .bss : 0xc04e1ef8 - 0xc0579aec   ( 607 kB)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000]  RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[    0.000000] NR_IRQS:16 nr_irqs:16 16
[    0.000000] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956969942ns
[    0.000000] sched_clock: 32 bits at 160MHz, resolution 6ns, wraps every 26843545593ns
[    0.000000] Console: colour dummy device 80x30
[    0.000199] Calibrating delay loop... 1915.28 BogoMIPS (lpj=9576448)
[    0.059903] pid_max: default: 32768 minimum: 301
[    0.060087] Mount-cache hash table entries: 512
[    0.065124] CPU: Testing write buffer coherency: ok
[    0.065471] /cpus/cpu@0 missing clock-frequency property
[    0.065491] /cpus/cpu@1 missing clock-frequency property
[    0.065507] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[    0.065537] Setting up static identity map for 0x40011938 - 0x4001196c
[    0.120593] CPU1: Booted secondary processor
[    0.180167] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[    0.180287] Brought up 2 CPUs
[    0.180308] SMP: Total of 2 processors activated.
[    0.180315] CPU: All CPU(s) started in HYP mode.
[    0.180320] CPU: Virtualization extensions available.
[    0.184886] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 4
[    0.185168] pinctrl core: initialized pinctrl subsystem
[    0.185506] regulator-dummy: no parameters
[    0.185814] NET: Registered protocol family 16
[    0.186112] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.193455] bio: create slab <bio-0> at 0
[    0.193964] reg-fixed-voltage ahci-5v.3: could not find pctldev for node /soc@01c00000/pinctrl@01c20800/ahci_pwr_pin@0, deferring probe
[    0.193990] platform ahci-5v.3: Driver reg-fixed-voltage requests probe deferral
[    0.194020] reg-fixed-voltage usb1-vbus.4: could not find pctldev for node /soc@01c00000/pinctrl@01c20800/usb1_vbus_pin@0, deferring probe
[    0.194034] platform usb1-vbus.4: Driver reg-fixed-voltage requests probe deferral
[    0.194056] reg-fixed-voltage usb2-vbus.5: could not find pctldev for node /soc@01c00000/pinctrl@01c20800/usb2_vbus_pin@0, deferring probe
[    0.194070] platform usb2-vbus.5: Driver reg-fixed-voltage requests probe deferral
[    0.194484] SCSI subsystem initialized
[    0.194900] usbcore: registered new interface driver usbfs
[    0.194960] usbcore: registered new interface driver hub
[    0.195067] usbcore: registered new device driver usb
[    0.195192] pps_core: LinuxPPS API ver. 1 registered
[    0.195203] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.195225] PTP clock support registered
[    0.195969] Switched to clocksource timer
[    0.200189] Clockevents: could not switch to one-shot mode:
[    0.200195] Clockevents: could not switch to one-shot mode: dummy_timer is not functional.
[    0.200207] Could not switch to high resolution mode on CPU 0
[    0.200220]  dummy_timer is not functional.
[    0.200227] Could not switch to high resolution mode on CPU 1
[    0.201498] NET: Registered protocol family 2
[    0.202368] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
[    0.202458] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[    0.202580] TCP: Hash tables configured (established 8192 bind 8192)
[    0.202666] TCP: reno registered
[    0.202682] UDP hash table entries: 512 (order: 2, 16384 bytes)
[    0.202738] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[    0.203064] NET: Registered protocol family 1
[    0.204238] audit: initializing netlink socket (disabled)
[    0.204290] type=2000 audit(0.190:1): initialized
[    0.204898] bounce pool size: 64 pages
[    0.211006] VFS: Disk quotas dquot_6.5.2
[    0.211271] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    0.212863] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.212875] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.213382] msgmni has been set to 1491
[    0.214114] io scheduler noop registered
[    0.214131] io scheduler deadline registered
[    0.214167] io scheduler cfq registered (default)
[    0.214429] platform 1c13400.phy: Driver sun4i-usb-phy requests probe deferral
[    0.216654] sunxi-pinctrl 1c20800.pinctrl: initialized sunXi PIO driver
[    0.249286] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[    0.272202] 1c28000.serial: ttyS0 at MMIO 0x1c28000 (irq = 33, base_baud = 1500000) is a U6_16550A
[    0.841405] console [ttyS0] enabled
[    0.866634] dw-apb-uart 1c29800.serial: Couldn't set LCR to 0
[    0.873380] dw-apb-uart 1c29800.serial: Couldn't set LCR to 0
[    0.879163] 1c29800.serial: ttyS1 at MMIO 0x1c29800 (irq = 51, base_baud = 1500000) is a U6_16550A
[    0.909900] dw-apb-uart 1c29c00.serial: Couldn't set LCR to 0
[    0.916645] dw-apb-uart 1c29c00.serial: Couldn't set LCR to 0
[    0.922422] 1c29c00.serial: ttyS2 at MMIO 0x1c29c00 (irq = 52, base_baud = 1500000) is a U6_16550A
[    0.932073] platform 1c18000.sata: Driver ahci-sunxi requests probe deferral
[    0.941563] stmmaceth 1c50000.ethernet: dummy supplies not allowed
[    0.947751] stmmaceth 1c50000.ethernet: no regulator found
[    0.953327] stmmaceth 1c50000.ethernet: no reset control found
[    0.959156]  Ring mode enabled
[    0.962226]  No HW DMA feature register supported
[    0.966751]  Normal descriptors
[    0.970073]  TX Checksum insertion supported
[    0.986126] libphy: stmmac: probed
[    0.989549] eth0: PHY ID 3fff3fff at 0 IRQ 0 (stmmac-0:00) active
[    0.995695] eth0: PHY ID 1fff1fff at 1 IRQ 0 (stmmac-0:01)
[    1.001202] eth0: PHY ID 3fff1fff at 2 IRQ 0 (stmmac-0:02)
[    1.006685] eth0: PHY ID 1fff1fff at 3 IRQ 0 (stmmac-0:03)
[    1.012236] eth0: PHY ID 1fff1fff at 4 IRQ 0 (stmmac-0:04)
[    1.017719] eth0: PHY ID 0fff1fff at 5 IRQ 0 (stmmac-0:05)
[    1.023222] eth0: PHY ID 0fff1fff at 6 IRQ 0 (stmmac-0:06)
[    1.028705] eth0: PHY ID 0fff0fff at 7 IRQ 0 (stmmac-0:07)
[    1.034250] eth0: PHY ID 0fff0fff at 8 IRQ 0 (stmmac-0:08)
[    1.039732] eth0: PHY ID 07ff0fff at 9 IRQ 0 (stmmac-0:09)
[    1.045233] eth0: PHY ID 0fff0fff at 10 IRQ 0 (stmmac-0:0a)
[    1.050816] eth0: PHY ID 07ff07ff at 11 IRQ 0 (stmmac-0:0b)
[    1.056385] eth0: PHY ID 07ff07ff at 12 IRQ 0 (stmmac-0:0c)
[    1.061966] eth0: PHY ID 07ff07ff at 13 IRQ 0 (stmmac-0:0d)
[    1.067534] eth0: PHY ID 03ff03ff at 14 IRQ 0 (stmmac-0:0e)
[    1.073112] eth0: PHY ID 03ff07ff at 15 IRQ 0 (stmmac-0:0f)
[    1.078680] eth0: PHY ID 03ff07ff at 16 IRQ 0 (stmmac-0:10)
[    1.084257] eth0: PHY ID 03ff03ff at 17 IRQ 0 (stmmac-0:11)
[    1.089824] eth0: PHY ID 03ff03ff at 18 IRQ 0 (stmmac-0:12)
[    1.095401] eth0: PHY ID 03ff03ff at 19 IRQ 0 (stmmac-0:13)
[    1.100978] eth0: PHY ID 03ff01ff at 20 IRQ 0 (stmmac-0:14)
[    1.106546] eth0: PHY ID 03ff03ff at 21 IRQ 0 (stmmac-0:15)
[    1.112122] eth0: PHY ID 01ff01ff at 22 IRQ 0 (stmmac-0:16)
[    1.117690] eth0: PHY ID 01ff03ff at 23 IRQ 0 (stmmac-0:17)
[    1.123266] eth0: PHY ID 01ff00ff at 24 IRQ 0 (stmmac-0:18)
[    1.128835] eth0: PHY ID 00ff00ff at 25 IRQ 0 (stmmac-0:19)
[    1.134416] eth0: PHY ID 01ff00ff at 26 IRQ 0 (stmmac-0:1a)
[    1.139984] eth0: PHY ID 01ff00ff at 27 IRQ 0 (stmmac-0:1b)
[    1.145563] eth0: PHY ID 00ff00ff at 28 IRQ 0 (stmmac-0:1c)
[    1.151170] eth0: PHY ID 00ff00ff at 29 IRQ 0 (stmmac-0:1d)
[    1.156739] eth0: PHY ID 00ff01ff at 30 IRQ 0 (stmmac-0:1e)
[    1.162322] eth0: PHY ID 00ff00ff at 31 IRQ 0 (stmmac-0:1f)
[    1.168007] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.174558] ehci-platform: EHCI generic platform driver
[    1.179939] platform 1c14000.usb: Driver ehci-platform requests probe deferral
[    1.187246] platform 1c1c000.usb: Driver ehci-platform requests probe deferral
[    1.194628] usbcore: registered new interface driver usb-storage
[    1.200851] mousedev: PS/2 mouse device common for all mice
[    1.206759] input: 1c22800.lradc as /devices/soc.2/1c22800.lradc/input/input0
[    1.215334] sunxi-wdt 1c20c90.watchdog: Watchdog enabled (timeout=16 sec, nowayout=0)
[    1.223644] sunxi-mmc 1c0f000.mmc: dummy supplies not allowed
[    1.229840] sunxi-mmc 1c0f000.mmc: Got CD GPIO #234.
[    1.235023] sunxi-mmc 1c0f000.mmc: base:0xf00fa000 irq:64
[    1.241183] TCP: cubic registered
[    1.244502] Initializing XFRM netlink socket
[    1.248794] NET: Registered protocol family 17
[    1.253408] Bridge firewalling registered
[    1.257426] 8021q: 802.1Q VLAN Support v1.8
[    1.261901] Registering SWP/SWPB emulation handler
[    1.267022] registered taskstats version 1
[    1.271811] ahci-5v: 5000 mV
[    1.275158] usb1-vbus: 5000 mV
[    1.278585] usb2-vbus: 5000 mV
[    1.350157] ahci-sunxi 1c18000.sata: controller can't do PMP, turning off CAP_PMP
[    1.357643] ahci-sunxi 1c18000.sata: forcing PORTS_IMPL to 0x1
[    1.363535] ahci-sunxi 1c18000.sata: AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl platform mode
[    1.372500] ahci-sunxi 1c18000.sata: flags: ncq sntf pm led clo only pio slum part ccc
[    1.381206] scsi0 : ahci_platform
[    1.384817] ata1: SATA max UDMA/133 mmio [mem 0x01c18000-0x01c18fff] port 0x100 irq 88
[    1.393052] ehci-platform 1c14000.usb: EHCI Host Controller
[    1.398653] ehci-platform 1c14000.usb: new USB bus registered, assigned bus number 1
[    1.406520] ehci-platform 1c14000.usb: irq 71, io mem 0x01c14000
[    1.430156] ehci-platform 1c14000.usb: USB 2.0 started, EHCI 1.00
[    1.436438] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    1.443231] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.450451] usb usb1: Product: EHCI Host Controller
[    1.455325] usb usb1: Manufacturer: Linux 3.13.7 ehci_hcd
[    1.460724] usb usb1: SerialNumber: 1c14000.usb
[    1.465706] hub 1-0:1.0: USB hub found
[    1.469493] hub 1-0:1.0: 1 port detected
[    1.473888] ehci-platform 1c1c000.usb: EHCI Host Controller
[    1.479481] ehci-platform 1c1c000.usb: new USB bus registered, assigned bus number 2
[    1.487326] ehci-platform 1c1c000.usb: irq 72, io mem 0x01c1c000
[    1.510151] ehci-platform 1c1c000.usb: USB 2.0 started, EHCI 1.00
[    1.516428] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[    1.523217] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.530437] usb usb2: Product: EHCI Host Controller
[    1.535311] usb usb2: Manufacturer: Linux 3.13.7 ehci_hcd
[    1.540709] usb usb2: SerialNumber: 1c1c000.usb
[    1.545670] hub 2-0:1.0: USB hub found
[    1.549456] hub 2-0:1.0: 1 port detected
[    1.553727] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[    1.657722] mmc0: host does not support reading read-only switch. assuming write-enable.
[    1.740163] ata1: SATA link down (SStatus 0 SControl 300)
[    1.760244] Waiting for root device /dev/mmcblk0p2...
[    1.850151] mmc0: new high speed SDHC card at address 0007
[    1.856040] isa bounce pool size: 16 pages
[    1.860313] mmcblk0: mmc0:0007 SD8GB 7.42 GiB
[    1.866522]  mmcblk0: p1 p2
[    1.870248] usb 2-1: new high-speed USB device number 2 using ehci-platform
[    1.871660] EXT4-fs (mmcblk0p2): couldn't mount as ext3 due to feature incompatibilities
[    1.872823] EXT4-fs (mmcblk0p2): couldn't mount as ext2 due to feature incompatibilities
[    1.898245] EXT4-fs (mmcblk0p2): mounted filesystem without journal. Opts: (null)
[    1.905930] VFS: Mounted root (ext4 filesystem) readonly on device 179:2.
[    1.913070] Freeing unused kernel memory: 184K (c048a000 - c04b8000)
procd: Console is alive
procd: - watchdog -
[    2.054214] usb 2-1: New USB device found, idVendor=0b95, idProduct=7720
[    2.061028] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[    2.068215] usb 2-1: Product: AX88x72A
[    2.072028] usb 2-1: Manufacturer: ASIX Elec. Corp.
[    2.076938] usb 2-1: SerialNumber: B0F07C
[    2.364279] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    2.376816] sdhci: Secure Digital Host Controller Interface driver
[    2.383035] sdhci: Copyright(c) Pierre Ossman
[    2.387975] sdhci-pltfm: SDHCI platform and OF driver helper
procd: - preinit -
probing /dev/mmcblk0 for uboot env data
Detected generic sunxi // generic sunxi
[    2.497169] random: mktemp urandom read with 20 bits of entropy available
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
mounting /dev/root
[    5.579129] EXT4-fs (mmcblk0p2): warning: mounting unchecked fs, running e2fsck is recommended
[    6.267192] EXT4-fs (mmcblk0p2): re-mounted. Opts: (null)
procd: - early -
procd: - watchdog -
Failed to connect to ubus
procd: - ubus -
procd: - init -
Please press Enter to activate this console.
[    7.927054] NET: Registered protocol family 10
[    7.940473] Modular ISDN core version 1.1.29
[    7.945002] NET: Registered protocol family 34
[    7.951249] DSP module 2.0
[    7.953990] mISDN_dsp: DSP clocks every 80 samples. This equals 1 jiffies.
[    7.981096] mISDN: Layer-1-over-IP driver Rev. 2.00
[    7.987512] 0 virtual devices registered
[    8.015115] ISDN subsystem Rev: 1.1.2.3/1.1.2.2/1.1.2.3/1.1.2.2/1.1.2.2 loaded
[    8.023773] PPP BSD Compression module registered
[    8.029374] dss1_divert module successfully installed
[    8.041299] nf_conntrack version 0.5.0 (16156 buckets, 64624 max)
[    8.051667] ip6_tables: (C) 2000-2006 Netfilter Core Team
[    8.073786] sunxi-rtc 1c20d00.rtc: rtc core: registered rtc-sunxi as rtc0
[    8.080722] sunxi-rtc 1c20d00.rtc: RTC enabled
[    8.087562] Micrel/Kendin KS8995 Ethernet switch SPI driver version 0.1.1
[    8.116114] hidraw: raw HID events driver (C) Jiri Kosina
[    8.167513] usbcore: registered new interface driver cdc_acm
[    8.173891] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[    8.183109] usbcore: registered new interface driver cdc_wdm
[    8.193103] gigaset: Driver for Gigaset 307x
[    8.197401] gigaset: ISDN4Linux interface
[    8.203924] ip_tables: (C) 2000-2006 Netfilter Core Team
[    8.210280] usbcore: registered new interface driver ipheth
[    8.292204] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver
[    8.299782] usbcore: registered new interface driver pegasus
[    8.307291] PPP generic driver version 2.4.2
[    8.312836] NET: Registered protocol family 24
[    8.327724] usbcore: registered new interface driver ums-alauda
[    8.334882] usbcore: registered new interface driver ums-cypress
[    8.342873] usbcore: registered new interface driver ums-datafab
[    8.350061] usbcore: registered new interface driver ums-freecom
[    8.357371] usbcore: registered new interface driver ums-isd200
[    8.365218] usbcore: registered new interface driver ums-jumpshot
[    8.372682] usbcore: registered new interface driver ums-karma
[    8.379716] usbcore: registered new interface driver ums-sddr09
[    8.387644] usbcore: registered new interface driver ums-sddr55
[    8.395035] usbcore: registered new interface driver ums-usbat
[    8.402433] usbcore: registered new interface driver usb_gigaset
[    8.409030] usb_gigaset: USB Driver for Gigaset 307x using M105
[    8.420574] usbcore: registered new interface driver usbserial
[    8.426712] usbcore: registered new interface driver usbserial_generic
[    8.434295] usbserial: USB Serial support registered for generic
[    8.467828] xt_time: kernel timezone is -0000
[    8.792144] asix 2-1:1.0 eth1: register 'asix' at usb-1c1c000.usb-1, ASIX AX88772 USB 2.0 Ethernet, 00:14:d1:b0:f0:7c
[    8.809305] usbcore: registered new interface driver asix
[    8.816825] usbcore: registered new interface driver bas_gigaset
[    8.822911] bas_gigaset: USB Driver for Gigaset 307x
[    8.829031] usbcore: registered new interface driver cdc_eem
[    8.841872] usbcore: registered new interface driver cdc_ether
[    8.850639] usbcore: registered new interface driver cdc_ncm
[    8.857477] usbcore: registered new interface driver cdc_subset
[    8.864998] usbcore: registered new interface driver dm9601
[    8.872702] usbcore: registered new interface driver kalmia
[    8.879504] usbcore: registered new interface driver MOSCHIP usb-ethernet driver
[    8.894016] usbcore: registered new interface driver qmi_wwan
[    8.901502] usbcore: registered new interface driver rndis_host
[    8.908782] usbcore: registered new interface driver sierra_net
[    8.916452] usbcore: registered new interface driver smsc95xx
[    8.925015] usbcore: registered new interface driver cdc_mbim
[    8.936255] usbcore: registered new interface driver option
[    8.942102] usbserial: USB Serial support registered for GSM modem (1-port)
[   11.305275] random: nonblocking pool is initialized
procd: - init complete -



BusyBox v1.22.1 (2014-08-19 23:13:30 EEST) built-in shell (ash)
Enter 'help' for a list of built-in commands.

  _______                     ________        __
 |       |.-----.-----.-----.|  |  |  |.----.|  |_
 |   -   ||  _  |  -__|     ||  |  |  ||   _||   _|
 |_______||   __|_____|__|__||________||__|  |____|
          |__| W I R E L E S S   F R E E D O M
 -----------------------------------------------------
 CHAOS CALMER (Bleeding Edge, r42220)
 -----------------------------------------------------
  * 1 1/2 oz Gin            Shake with a glassful
  * 1/4 oz Triple Sec       of broken ice and pour
  * 3/4 oz Lime Juice       unstrained into a goblet.
  * 1 1/2 oz Orange Juice
  * 1 tsp. Grenadine Syrup
 -----------------------------------------------------
root@OpenWrt:/#


Attachments (0)

Change History (8)

comment:1 Changed 3 years ago by viljar.rooda@…

second boot is correct one first one sd card was badly connected.

comment:2 Changed 3 years ago by wigyori

  • Owner changed from developers to wigyori
  • Status changed from new to assigned

comment:3 Changed 3 years ago by wigyori

Please test with the updated 3.14.x kernel.

comment:4 Changed 3 years ago by thewerthfam@…

kernel version 3.14.18
CHAOS CALMER (Bleeding Edge, r42861)

Doesn't work either.
ifconfig doesn't show an defined wlan device. This is the case or both (ARM)brcm2708 and allwinner platform Banana PI.

modprobe rtl8192cu shows module loaded.

This 8192cu wifi device works on ubuntu 14.04 i686 running 3.13.x shows the same kernel modules for the 8192cu device. Is openwrt using the mainline 3.14 kernel? If so it should have the latest rtl8192 drivers. right?

Tried to compile the latest drivers from the rtl site but got loads of errors.


comment:5 Changed 3 years ago by thewerthfam@…

This thread maybe of use also. http://blog.stuffedcow.net/2014/04/rtl8192cu-and-linux-3-13-10/

Seems that even in the mainline linux kernel the driver seems to work - at least produces wireless device file and does some networking - anyone who tries to use the driver for anything substantial will discover that it really doesn't work. As of just recently there have been some positive bug fixes for this driver in the 3.16.x kernel series.

comment:6 Changed 3 years ago by Bouv

Hello. Any news on this assignés défectueux ?

comment:7 Changed 3 years ago by Bouv

Hello. Any news on this assign défect ?

comment:8 Changed 22 months ago by alexvf

Is this an OpenWrt bug? Is it related to unsupported hardware?
I'm facing a similar issue on an Allwinner A20 board. I followed https://wiki.openwrt.org/doc/hardware/soc/soc.allwinner.sunxi to build an SD card image from buildroot and it seems that Ethernet driver fails:

root@OpenWrt:/etc/config# ifconfig eth0 up
[10391.790679] stmmac_hw_setup: DMA engine initialization failed
[10391.796441] stmmac_open: Hw setup failed
ifconfig: SIOCSIFFLAGS: Resource busy

I can provide more information if you need it.

Add Comment

Modify Ticket

Action
as assigned .
Author


E-mail address and user name can be saved in the Preferences.

 
Note: See TracTickets for help on using tickets.