Modify

Opened 4 years ago

Closed 4 years ago

#15280 closed defect (fixed)

easybox 802, no tx power frm rt2800pci

Reported by: anonymous Owned by: developers
Priority: normal Milestone: Attitude Adjustment 12.09.1
Component: packages Version: Trunk
Keywords: Cc:

Description

Only when the antennas are very very close I can get connected to the router. USB adapter rt2770 works great. PRoblem with rt2800pci.

Attachments (0)

Change History (6)

comment:1 Changed 4 years ago by anonymous

same result with breaking barier trunk.

comment:2 Changed 4 years ago by anonymous

boot log

[ 0.000000] Linux version 3.3.8 (sebiks@ubuntu) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #1 Sun Mar 16 01:53:23 CET 2014
[ 0.000000] SoC: Danube rev 1.5
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU revision is: 00019641 (MIPS 24KEc)
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone PFN ranges:
[ 0.000000] Normal 0x00000000 -> 0x00004000
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] Early memory PFN ranges
[ 0.000000] 0: 0x00000000 -> 0x00004000
[ 0.000000] On node 0 totalpages: 16384
[ 0.000000] free_area_init_node: node 0, pgdat 802a3240, node_mem_map 81000000
[ 0.000000] Normal zone: 128 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 16256 pages, LIFO batch:3
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
[ 0.000000] Kernel command line: console=ttyLTQ1,115200 rootfstype=squashfs,jffs2 machtype=ARV752DPW
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Primary instruction cache 16kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 32 bytes
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 61832k/65536k available (2296k kernel code, 3704k reserved, 398k data, 172k init, 0k highmem)
[ 0.000000] NR_IRQS:256
[ 0.000000] CPU Clock: 333MHz
[ 0.000000] Calibrating delay loop... 221.18 BogoMIPS (lpj=442368)
[ 0.036000] pid_max: default: 32768 minimum: 301
[ 0.040000] Mount-cache hash table entries: 512
[ 0.048000] NET: Registered protocol family 16
[ 0.056000] gpiochip_add: registered GPIOs 0 to 15 on device: ltq_gpio
[ 0.060000] gpiochip_add: registered GPIOs 16 to 31 on device: ltq_gpio
[ 0.064000] MIPS: machine is ARV752DPW - Arcor A802
[ 0.068000] gpiochip_add: registered GPIOs 100 to 115 on device: ltq_ebu
[ 0.104000] bio: create slab <bio-0> at 0
[ 0.112000] PCI host bridge to bus 0000:00
[ 0.116000] pci_bus 0000:00: root bus resource [mem 0x18000000-0x19ffffff]
[ 0.120000] pci_bus 0000:00: root bus resource [io 0x1ae00000-0x1affffff]
[ 0.124000] pci 0000:00:0e.0: [1814:0601] type 0 class 0x000280
[ 0.124000] pci 0000:00:0e.0: reg 10: [mem 0xffff0000-0xffffffff]
[ 0.124000] pci 0000:00:0e.0: PME# supported from D0 D3hot D3cold
[ 0.124000] pci 0000:00:0e.0: BAR 0: assigned [mem 0x18000000-0x1800ffff]
[ 0.128000] pci 0000:00:0e.0: SLOT:14 PIN:1 IRQ:135
[ 0.132000] Switching to clocksource MIPS
[ 0.140000] NET: Registered protocol family 2
[ 0.148000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.152000] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
[ 0.160000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.168000] TCP: Hash tables configured (established 2048 bind 2048)
[ 0.172000] TCP reno registered
[ 0.176000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.184000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.188000] NET: Registered protocol family 1
[ 0.192000] PCI: CLS 0 bytes, default 32
[ 0.196000] gptu: totally 6 16-bit timers/counters
[ 0.200000] gptu: misc_register on minor 63
[ 0.204000] gptu: succeeded to request irq 126
[ 0.208000] gptu: succeeded to request irq 127
[ 0.212000] gptu: succeeded to request irq 128
[ 0.216000] gptu: succeeded to request irq 129
[ 0.224000] gptu: succeeded to request irq 130
[ 0.228000] gptu: succeeded to request irq 131
[ 0.236000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.240000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.252000] msgmni has been set to 120
[ 0.256000] io scheduler noop registered
[ 0.260000] io scheduler deadline registered (default)
[ 0.264000] ltq_asc.1: ttyLTQ1 at MMIO 0x1e100c00 (irq = 112) is a ltq_asc
[ 0.272000] console [ttyLTQ1] enabled, bootconsole disabled
[ 0.288000] ltq_nor: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x0022cb
[ 0.296000] ltq_nor: Found an alias at 0x800000 for the chip at 0x0
[ 0.296000] Amd/Fujitsu Extended Query Table at 0x0040
[ 0.300000] Amd/Fujitsu Extended Query version 1.1.
[ 0.304000] number of CFI chips: 1
[ 0.308000] Creating 4 MTD partitions on "ltq_nor":
[ 0.312000] 0x000000000000-0x000000010000 : "uboot"
[ 0.320000] 0x000000010000-0x000000020000 : "uboot_env"
[ 0.328000] 0x000000020000-0x0000007f0000 : "linux"
[ 0.336000] found squashfs behind kernel
[ 0.336000] Creating 2 MTD partitions on "ltq_nor":
[ 0.340000] 0x000000020000-0x00000010e6cd : "kernel"
[ 0.348000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 0.364000] 0x00000010e6cd-0x0000007f0000 : "rootfs"
[ 0.364000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 0.380000] mtd: partition "rootfs" set to be root filesystem
[ 0.384000] mtd: partition "rootfs_data" created automatically, ofs=3D0000, len=420000
[ 0.392000] 0x0000003d0000-0x0000007f0000 : "rootfs_data"
[ 0.400000] 0x0000007f0000-0x000000800000 : "board_config"
[ 0.428000] ltq_mii: probed
[ 0.460000] Registering RTL8306SDM switch with Chip ID: 0x5988, version: 0x0000
[ 0.464000] eth0: attached PHY [Realtek RTL8306S] (phy_addr=ltq_etop-fffffff:00, irq=-1)
[ 0.476000] Registered led device: soc:blue:power
[ 0.480000] Registered led device: soc:red:internet
[ 0.480000] Registered led device: soc:red:power
[ 0.480000] Registered led device: soc:red:wps
[ 0.480000] Registered led device: soc:red:fxo
[ 0.480000] Registered led device: soc:red:voice
[ 0.480000] Registered led device: soc:green:usb
[ 0.484000] Registered led device: soc:green:wifi
[ 0.484000] Registered led device: soc:green:wifi1
[ 0.484000] Registered led device: soc:blue:wifi
[ 0.484000] Registered led device: soc:blue:wifi1
[ 0.484000] Registered led device: soc:green:eth1
[ 0.484000] Registered led device: soc:green:eth2
[ 0.488000] Registered led device: soc:green:eth3
[ 0.488000] Registered led device: soc:green:eth4
[ 0.488000] TCP cubic registered
[ 0.492000] NET: Registered protocol family 17
[ 0.496000] 8021q: 802.1Q VLAN Support v1.8
[ 0.516000] VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
[ 0.524000] Freeing unused kernel memory: 172k freed
[ 7.340000] JFFS2 notice: (354) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (0 unchecked, 0 orphan) and 6 of xref (0 dead, 0 orphan) found.
[ 10.204000] Loading modules backported from Linux version master-2014-01-23-0-g62c147d
[ 10.212000] Backport generated by backports.git backports-20140124-0-g1256d3e
[ 10.536000] cfg80211: Calling CRDA to update world regulatory domain
[ 10.540000] cfg80211: World regulatory domain updated:
[ 10.544000] cfg80211: DFS Master region: unset
[ 10.548000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 10.556000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 10.564000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 10.572000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 10.580000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (300 mBi, 2000 mBm)
[ 10.588000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (300 mBi, 2000 mBm)
[ 10.592000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm)
[ 11.324000] SCSI subsystem initialized
[ 11.808000] usbcore: registered new interface driver usbfs
[ 11.812000] usbcore: registered new interface driver hub
[ 11.820000] usbcore: registered new device driver usb
[ 12.960000] usbcore: registered new interface driver rt2800usb
[ 12.992000] PCI: Enabling device 0000:00:0e.0 (0000 -> 0002)
[ 12.996000] rt2800pci 0000:00:0e.0: setting latency timer to 64
[ 12.996000] ieee80211 phy0: rt2x00lib_request_eeprom_file: Info - Loading EEPROM data from 'RT2860.eeprom'.
[ 13.172000] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 2860, rev 0103 detected
[ 13.180000] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 0003 detected
[ 13.184000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 13.188000] Registered led device: rt2800pci-phy0::radio
[ 13.188000] Registered led device: rt2800pci-phy0::assoc
[ 13.188000] Registered led device: rt2800pci-phy0::quality
[ 13.356000] NET: Registered protocol family 8
[ 13.360000] NET: Registered protocol family 20
[ 13.452000] Button Hotplug driver version 0.4.1
[ 14.500000] PPP generic driver version 2.4.2
[ 15.480000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 15.848000] NET: Registered protocol family 24
[ 16.036000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 16.184000] nf_conntrack version 0.5.0 (968 buckets, 3872 max)
[ 17.256000] dwc_otg: version 2.60a 22-NOV-2006
[ 17.864000] DWC_otg: Using DMA mode
[ 17.864000] dwc_otg dwc_otg.0: DWC OTG Controller
[ 17.872000] dwc_otg dwc_otg.0: new USB bus registered, assigned bus number 1
[ 17.876000] dwc_otg dwc_otg.0: irq 62, io mem 0xffffffffbe101000
[ 17.888000] DWC_otg: Init: Port Power? op_state=1
[ 17.888000] DWC_otg: Init: Power Port (0)
[ 17.896000] hub 1-0:1.0: USB hub found
[ 17.896000] hub 1-0:1.0: 1 port detected
[ 17.928000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 18.084000] DISCONNECTED PORT
[ 18.088000] uhci_hcd: USB Universal Host Controller Interface driver
[ 18.156000] usbcore: registered new interface driver snd-usb-audio
[ 18.356000] usbcore: registered new interface driver usbserial
[ 18.360000] USB Serial support registered for generic
[ 18.368000] usbcore: registered new interface driver usbserial_generic
[ 18.372000] usbserial: USB Serial Driver core
[ 18.476000] Initializing USB Mass Storage driver...
[ 18.480000] usbcore: registered new interface driver usb-storage
[ 18.484000] USB Mass Storage support registered.
[ 18.512000] usbcore: registered new interface driver ums-alauda
[ 18.540000] usbcore: registered new interface driver ums-cypress
[ 18.568000] usbcore: registered new interface driver ums-datafab
[ 18.596000] usbcore: registered new interface driver ums-freecom
[ 18.624000] usbcore: registered new interface driver ums-isd200
[ 18.676000] usbcore: registered new interface driver ums-jumpshot
[ 18.720000] usbcore: registered new interface driver ums-karma
[ 18.748000] usbcore: registered new interface driver ums-sddr09
[ 18.780000] usbcore: registered new interface driver ums-sddr55
[ 18.808000] usbcore: registered new interface driver ums-usbat
[ 18.860000] usbcore: registered new interface driver cdc_ether
[ 19.028000] input: gpio-keys-polled as /devices/platform/gpio-keys-polled/input/input0
[ 19.168000] usbcore: registered new interface driver rndis_host
[ 19.200000] USB Serial support registered for GSM modem (1-port)
[ 19.208000] usbcore: registered new interface driver option
[ 19.212000] option: v0.7.2:USB Driver for GSM modems
[ 19.244000] USB Serial support registered for Qualcomm USB modem
[ 19.248000] usbcore: registered new interface driver qcserial
[ 26.280000] device eth0 entered promiscuous mode
[ 26.288000] br-lan: port 1(eth0) entered forwarding state
[ 26.292000] br-lan: port 1(eth0) entered forwarding state
[ 28.296000] br-lan: port 1(eth0) entered forwarding state
[ 30.848000] ieee80211 phy0: rt2x00lib_request_firmware: Info - Loading firmware file 'rt2860.bin'
[ 30.900000] ieee80211 phy0: rt2x00lib_request_firmware: Info - Firmware detected - version: 0.34
[ 30.948000] device wlan0 entered promiscuous mode
[ 30.968000] br-lan: port 2(wlan0) entered forwarding state
[ 30.972000] br-lan: port 2(wlan0) entered forwarding state
[ 32.976000] br-lan: port 2(wlan0) entered forwarding state
[ 403.284000] device wlan0 left promiscuous mode
[ 403.288000] br-lan: port 2(wlan0) entered disabled state
[ 404.824000] device wlan0 entered promiscuous mode
[ 404.844000] br-lan: port 2(wlan0) entered forwarding state
[ 404.848000] br-lan: port 2(wlan0) entered forwarding state
[ 406.852000] br-lan: port 2(wlan0) entered forwarding state

comment:3 Changed 4 years ago by anonymous

iw phy0 info

Wiphy phy0

Band 1:

Capabilities: 0x172

HT20/HT40
Static SM Power Save
RX Greenfield
RX HT20 SGI
RX HT40 SGI
RX STBC 1-stream
Max AMSDU length: 3839 bytes
No DSSS/CCK HT40

Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
Minimum RX AMPDU time spacing: 2 usec (0x04)
HT RX MCS rate indexes supported: 0-7, 32
TX unequal modulation supported
HT TX Max spatial streams: 4
HT TX MCS rate indexes supported may differ
Frequencies:

  • 2412 MHz [1] (20.0 dBm)
  • 2417 MHz [2] (20.0 dBm)
  • 2422 MHz [3] (20.0 dBm)
  • 2427 MHz [4] (20.0 dBm)
  • 2432 MHz [5] (20.0 dBm)
  • 2437 MHz [6] (20.0 dBm)
  • 2442 MHz [7] (20.0 dBm)
  • 2447 MHz [8] (20.0 dBm)
  • 2452 MHz [9] (20.0 dBm)
  • 2457 MHz [10] (20.0 dBm)
  • 2462 MHz [11] (20.0 dBm)
  • 2467 MHz [12] (20.0 dBm) (passive scanning, no IBSS)
  • 2472 MHz [13] (20.0 dBm) (passive scanning, no IBSS)
  • 2484 MHz [14] (20.0 dBm) (passive scanning, no IBSS)

Bitrates (non-HT):

  • 1.0 Mbps
  • 2.0 Mbps (short preamble supported)
  • 5.5 Mbps (short preamble supported)
  • 11.0 Mbps (short preamble supported)
  • 6.0 Mbps
  • 9.0 Mbps
  • 12.0 Mbps
  • 18.0 Mbps
  • 24.0 Mbps
  • 36.0 Mbps
  • 48.0 Mbps
  • 54.0 Mbps

max # scan SSIDs: 4
max scan IEs length: 2257 bytes
Coverage class: 0 (up to 0m)
Supported Ciphers:

  • WEP40 (00-0f-ac:1)
  • WEP104 (00-0f-ac:5)
  • TKIP (00-0f-ac:2)
  • CCMP (00-0f-ac:4)

Available Antennas: TX 0 RX 0
Supported interface modes:

  • IBSS
  • managed
  • AP
  • AP/VLAN
  • WDS
  • monitor
  • mesh point

software interface modes (can always be added):

  • AP/VLAN
  • monitor

valid interface combinations:

  • #{ managed, AP, mesh point } <= 8, total <= 8, #channels <= 1

Supported commands:

  • new_interface
  • set_interface
  • new_key
  • start_ap
  • new_station
  • new_mpath
  • set_mesh_config
  • set_bss
  • authenticate
  • associate
  • deauthenticate
  • disassociate
  • join_ibss
  • join_mesh
  • set_tx_bitrate_mask
  • frame
  • frame_wait_cancel
  • set_wiphy_netns
  • set_channel
  • set_wds_peer
  • probe_client
  • set_noack_map
  • register_beacons
  • Unknown command (89)
  • Unknown command (92)
  • Unknown command (104)
  • testmode
  • connect
  • disconnect

Supported TX frame types:

  • IBSS: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
  • managed: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
  • AP: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
  • AP/VLAN: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
  • mesh point: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
  • P2P-client: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
  • P2P-GO: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
  • (null): 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0

Supported RX frame types:

  • IBSS: 0x40 0xb0 0xc0 0xd0
  • managed: 0x40 0xd0
  • AP: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
  • AP/VLAN: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
  • mesh point: 0xb0 0xc0 0xd0
  • P2P-client: 0x40 0xd0
  • P2P-GO: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
  • (null): 0x40 0xd0

Device supports RSN-IBSS.
HT Capability overrides:

  • MCS: ff ff ff ff ff ff ff ff ff ff
  • maximum A-MSDU length
  • supported channel width
  • short GI for 40 MHz
  • max A-MPDU length exponent
  • min MPDU start spacing

Device supports TX status socket option.
Device supports HT-IBSS.

comment:4 Changed 4 years ago by anonymous

wireles config

config wifi-device radio0

option type mac80211
option channel 11
option hwmode 11ng
option path 'pci0000:00/0000:00:0e.0'
option htmode HT20
list ht_capab GF
list ht_capab SHORT-GI-20
list ht_capab SHORT-GI-40
list ht_capab RX-STBC1


config wifi-iface

option device radio0
option network lan
option mode ap
option ssid OpenWrt
option encryption none

comment:5 Changed 4 years ago by anonymous

with aa 12.09 everything works great

comment:6 Changed 4 years ago by blogic

  • Resolution set to fixed
  • Status changed from new to closed

Add Comment

Modify Ticket

Action
as closed .
The resolution will be deleted. Next status will be 'reopened'.
Author


E-mail address and user name can be saved in the Preferences.

 
Note: See TracTickets for help on using tickets.