Modify

Opened 4 years ago

Last modified 3 years ago

#14329 new defect

f5d8235v2 can't dispacht ip address to PC(WIFI is normal)

Reported by: Davidwei Owned by: developers
Priority: highest Milestone: Chaos Calmer 15.05
Component: base system Version: Trunk
Keywords: Cc:

Description

I install the newst fimware (get it from ​http://downloads.openwrt.org/snapshots/trunk/ramips/openwrt-ramips-rt305x-f5d8235v2-squashfs-sysupgrade.bin) on my Belkin f5d8235 v2.
two question
1.openwrt on f5d8235v2 can't dispacht ip address to PC.
2.if i reboot in openwrt system,the router will not back to openwrt system. The router will reboot and reboot.....

Flashing&first start inforamtion

multiple lines, ''no wiki''
      white space respected
 netboot_common, argc= 3 
 *************buf = 0x81fcf260
 **********NexTxPacket = 81fe7340

 NetTxPacket = 0x81FE7340 

 NetRxPackets[0] = 0x81FE7940

 NetRxPackets[1] = 0x81FE7F40

 NetRxPackets[2] = 0x81FE8540

 NetRxPackets[3] = 0x81FE8B40

 NetRxPackets[4] = 0x81FE9140

 NetRxPackets[5] = 0x81FE9740

 NetRxPackets[6] = 0x81FE9D40

 NetRxPackets[7] = 0x81FEA340

 NetRxPackets[8] = 0x81FEA940

 NetRxPackets[9] = 0x81FEAF40

 NetRxPackets[10] = 0x81FEB540

 NetRxPackets[11] = 0x81FEBB40

 NetRxPackets[12] = 0x81FEC140

 NetRxPackets[13] = 0x81FEC740

 NetRxPackets[14] = 0x81FECD40

 NetRxPackets[15] = 0x81FED340

 NetRxPackets[16] = 0x81FED940

 NetRxPackets[17] = 0x81FEDF40

 NetRxPackets[18] = 0x81FEE540

 NetRxPackets[19] = 0x81FEEB40

 KSEG1ADDR(NetTxPacket) = 0xA1FE7340 

 NetLoop,call eth_halt ! 

 NetLoop,call eth_init ! 
Trying Eth0 (10/100-M)

 Waitting for RX_DMA_BUSY status Start... done
0 smi_init check[0x0509]=0x5937
0 smi_init check[0x0509]=0x5937

 Header Payload scatter function is Disable !! 

 ETH_STATE_ACTIVE!! 
Using Eth0 (10/100-M) device
TFTP from server 192.168.2.2; our IP address is 192.168.2.1
Filename 'trunk20131016byopenwrt.bin'.

 TIMEOUT_COUNT=10,Load address: 0x80100000
Loading: *
ArpTimeoutCheck 
T Got ARP REQUEST, return our IP
checksum bad
Got ARP REQUEST, return our IP
checksum bad
checksum bad
T Got ARP REPLY, set server/gtwy eth addr (00:1f:d0:d0:50:35)
Got it
Got ARP REQUEST, return our IP
T #
 first block received  
################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         ############################################
done
Bytes transferred = 2883588 (2c0004 hex)
NetBootFileXferSize= 002c0004
Erase linux kernel block !!
From 0xBF050000 To 0xBF31FFFF

 b_end =BF7FFFFF
Erase Flash from 0xbf050000 to 0xbf31ffff in Bank # 1 

 erase sector  = 12 
sect = 12,s_last = 56,erase poll = 915286

 erase sector  = 13 
sect = 13,s_last = 56,erase poll = 896350

 erase sector  = 14 
*sect = 14,s_last = 56,erase poll = 900835

 erase sector  = 15 
sect = 15,s_last = 56,erase poll = 1058805

 erase sector  = 16 
*sect = 16,s_last = 56,erase poll = 917629

 erase sector  = 17 
sect = 17,s_last = 56,erase poll = 890512

 erase sector  = 18 
*sect = 18,s_last = 56,erase poll = 888696

 erase sector  = 19 
sect = 19,s_last = 56,erase poll = 903413

 erase sector  = 20 
sect = 20,s_last = 56,erase poll = 889783

 erase sector  = 21 
*sect = 21,s_last = 56,erase poll = 890353

 erase sector  = 22 
sect = 22,s_last = 56,erase poll = 901846

 erase sector  = 23 
*sect = 23,s_last = 56,erase poll = 913900

 erase sector  = 24 
sect = 24,s_last = 56,erase poll = 914190

 erase sector  = 25 
*sect = 25,s_last = 56,erase poll = 910630

 erase sector  = 26 
sect = 26,s_last = 56,erase poll = 897043

 erase sector  = 27 
*sect = 27,s_last = 56,erase poll = 900652

 erase sector  = 28 
sect = 28,s_last = 56,erase poll = 920126

 erase sector  = 29 
sect = 29,s_last = 56,erase poll = 895759

 erase sector  = 30 
*sect = 30,s_last = 56,erase poll = 890114

 erase sector  = 31 
sect = 31,s_last = 56,erase poll = 890357

 erase sector  = 32 
*sect = 32,s_last = 56,erase poll = 889637

 erase sector  = 33 
sect = 33,s_last = 56,erase poll = 892570

 erase sector  = 34 
*sect = 34,s_last = 56,erase poll = 899633

 erase sector  = 35 
sect = 35,s_last = 56,erase poll = 912677

 erase sector  = 36 
sect = 36,s_last = 56,erase poll = 893937

 erase sector  = 37 
*sect = 37,s_last = 56,erase poll = 934809

 erase sector  = 38 
sect = 38,s_last = 56,erase poll = 878033

 erase sector  = 39 
*sect = 39,s_last = 56,erase poll = 893814

 erase sector  = 40 
sect = 40,s_last = 56,erase poll = 902363

 erase sector  = 41 
*sect = 41,s_last = 56,erase poll = 890145

 erase sector  = 42 
sect = 42,s_last = 56,erase poll = 890287

 erase sector  = 43 
sect = 43,s_last = 56,erase poll = 918198

 erase sector  = 44 
*sect = 44,s_last = 56,erase poll = 905587

 erase sector  = 45 
sect = 45,s_last = 56,erase poll = 889537

 erase sector  = 46 
*sect = 46,s_last = 56,erase poll = 893571

 erase sector  = 47 
sect = 47,s_last = 56,erase poll = 877974

 erase sector  = 48 
*sect = 48,s_last = 56,erase poll = 902138

 erase sector  = 49 
sect = 49,s_last = 56,erase poll = 903502

 erase sector  = 50 
*sect = 50,s_last = 56,erase poll = 908284

 erase sector  = 51 
sect = 51,s_last = 56,erase poll = 889503

 erase sector  = 52 
sect = 52,s_last = 56,erase poll = 900899

 erase sector  = 53 
*sect = 53,s_last = 56,erase poll = 890359

 erase sector  = 54 
sect = 54,s_last = 56,erase poll = 890582

 erase sector  = 55 
*sect = 55,s_last = 56,erase poll = 912577

 erase sector  = 56 
sect = 56,s_last = 56,erase poll = 908027
 done
Erased 45 sectors

 Copy linux image[2883588 byte] to Flash[0xBF050000].... 
Copy to Flash... 
 Copy 2883588 byte to Flash... 
 addr = 0xBF0A409C ,cnt=2539368 
 addr = 0xBF0F813A ,cnt=2195146 
 addr = 0xBF14C1D8 ,cnt=1850924 
 addr = 0xBF1A0276 ,cnt=1506702 
 addr = 0xBF1F4314 ,cnt=1162480 
 addr = 0xBF2483B2 ,cnt=818258 
 addr = 0xBF29C450 ,cnt=474036 
 addr = 0xBF2F04EE ,cnt=129814 done
## Booting image at bf050000 ...
   Image Name:   MIPS OpenWrt Linux-3.10.15
   Created:      2013-10-16   2:11:12 UTC

 System Control Status = 0x10440000 
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    1013258 Bytes = 989.5 kB
   Load Address: 80000000
   Entry Point:  80000000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80000000) ...
## Giving linux memsize in MB, 32

Starting kernel ...

[    0.000000] Linux version 3.10.15 (openwrt@huchra) (gcc version 4.6.4 (OpenWrt/Linaro GCC 4.6-2013.05 r38413) ) #1 Tue Oct 15 19:09:38 PDT 2013
[    0.000000] SoC Type: Ralink RT3052 id:1 rev:3
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU revision is: 0001964c (MIPS 24KEc)
[    0.000000] MIPS: machine is Belkin F5D8235 v2
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 02000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x00000000-0x01ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x00000000-0x01ffffff]
[    0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 32 bytes
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 8128
[    0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2
[    0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
[    0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] Writing ErrCtl register=0002bc20
[    0.000000] Readback ErrCtl register=0002bc20
[    0.000000] Memory: 29224k/32768k available (2237k kernel code, 3544k reserved, 549k data, 220k init, 0k highmem)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS:128
[    0.000000] CPU Clock: 384MHz
[    0.000000] Calibrating delay loop... 255.59 BogoMIPS (lpj=1277952)
[    0.070000] pid_max: default: 32768 minimum: 301
[    0.080000] Mount-cache hash table entries: 512
[    0.090000] pinctrl core: initialized pinctrl subsystem
[    0.100000] NET: Registered protocol family 16
[    0.130000] bio: create slab <bio-0> at 0
[    0.140000] rt2880_gpio 10000600.gpio: registering 24 gpios
[    0.150000] rt2880_gpio 10000600.gpio: registering 24 irq handlers
[    0.160000] Switching to clocksource MIPS
[    0.170000] NET: Registered protocol family 2
[    0.180000] TCP established hash table entries: 512 (order: 0, 4096 bytes)
[    0.190000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)
[    0.210000] TCP: Hash tables configured (established 512 bind 512)
[    0.220000] TCP: reno registered
[    0.230000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.240000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.250000] NET: Registered protocol family 1
[    0.260000] rt-timer 10000100.timer: maximum frequncy is 7812Hz
[    0.300000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.310000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.330000] msgmni has been set to 57
[    0.340000] io scheduler noop registered
[    0.350000] io scheduler deadline registered (default)
[    0.360000] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[    0.380000] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20) is a 16550A
[    0.400000] console [ttyS0] enabled, bootconsole disabled
[    0.400000] console [ttyS0] enabled, bootconsole disabled
[    0.430000] 1f000000.cfi: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x0022cb
[    0.450000] Amd/Fujitsu Extended Query Table at 0x0040
[    0.460000]   Amd/Fujitsu Extended Query version 1.1.
[    0.470000] number of CFI chips: 1
[    0.470000] 4 ofpart partitions found on MTD device 1f000000.cfi
[    0.490000] Creating 4 MTD partitions on "1f000000.cfi":
[    0.500000] 0x000000000000-0x000000050000 : "u-boot"
[    0.510000] 0x000000050000-0x0000007e0000 : "firmware"
[    0.520000] 0x00000014764a-0x0000007e0000 : "rootfs"
[    0.530000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    0.560000] mtd: partition "rootfs" set to be root filesystem
[    0.570000] mtd: partition "rootfs_data" created automatically, ofs=0x2f0000, len=0x4f0000
[    0.590000] 0x0000002f0000-0x0000007e0000 : "rootfs_data"
[    0.600000] 0x0000007e0000-0x0000007f0000 : "nvram"
[    0.610000] 0x0000007f0000-0x000000800000 : "factory"
[    0.630000] eth0: done loading
[    0.640000] rt2880_wdt 10000120.watchdog: Initialized
[    0.650000] TCP: cubic registered
[    0.660000] NET: Registered protocol family 17
[    0.670000] Bridge firewalling registered
[    0.680000] 8021q: 802.1Q VLAN Support v1.8
[    0.690000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[    0.710000] Freeing unused kernel memory: 220K (802b9000 - 802f0000)
Console is alive
procd: Console is alive
- watchdog -
procd: - watchdog -
[    3.070000] usbcore: registered new interface driver usbfs
[    3.080000] usbcore: registered new interface driver hub
[    3.090000] usbcore: registered new device driver usb
[    3.100000] Button Hotplug driver version 0.4.1
[    3.120000] dwc_otg: version 2.72a 24-JUN-2008
[    3.130000] dwc_otg: Core Release: 2.66a
[    3.340000] dwc_otg: Periodic Transfer Interrupt Enhancement - disabled
[    3.350000] dwc_otg: Multiprocessor Interrupt Enhancement - disabled
[    3.360000] dwc_otg: Using DMA mode
[    3.370000] dwc_otg: Device using Buffer DMA mode
[    3.380000] dwc_otg 101c0000.otg: DWC OTG Controller
[    3.390000] dwc_otg 101c0000.otg: new USB bus registered, assigned bus number 1
[    3.400000] dwc_otg 101c0000.otg: irq 26, io mem 0x101c0000
[    3.420000] dwc_otg: Init: Port Power? op_state=1
[    3.430000] dwc_otg: Init: Power Port (0)
[    3.440000] hub 1-0:1.0: USB hub found
[    3.440000] hub 1-0:1.0: 1 port detected
[    3.450000] leds-gpio gpio-leds.4: pins are not configured from the driver
kmod: ran 16 iterations
- preinit -
procd: - preinit -
[    3.550000] dwc_otg: Device Not Supported
[    3.810000] dwc_otg: Device Not Supported
Press the [f] key and hit [enter] to enter failsafe mode
mount_root: jffs2 is not ready - marker found
- early -
procd: - early -
- watchdog -
procd: - watchdog -
- init -
procd: - init -
Please press Enter to activate this console.
[    8.210000] NET: Registered protocol family 10
[    8.230000] nf_conntrack version 0.5.0 (460 buckets, 1840 max)
[    8.250000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[    8.290000] Loading modules backported from Linux version master-2013-06-27-0-gdcfa6d5
[    8.300000] Backport generated by backports.git backports-20130617-4-ge3220f5
[    8.320000] ip_tables: (C) 2000-2006 Netfilter Core Team
[    8.380000] xt_time: kernel timezone is -0000
[    8.420000] cfg80211: Calling CRDA to update world regulatory domain
[    8.440000] cfg80211: World regulatory domain updated:
[    8.450000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[    8.460000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[    8.480000] cfg80211:   (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[    8.490000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[    8.510000] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[    8.520000] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[    8.600000] PPP generic driver version 2.4.2
[    8.610000] NET: Registered protocol family 24
[    8.650000] rt2800_wmac 10180000.wmac: failed to load eeprom property
[    8.660000] ieee80211 phy0: rt2x00lib_request_eeprom_file: Info - Loading EEPROM data from 'soc_wmac.eeprom'.
[    8.810000] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 2872, rev 0200 detected
[    8.820000] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 0008 detected
[   15.280000] device eth0.1 entered promiscuous mode
[   15.290000] device eth0 entered promiscuous mode
[   15.300000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.1: link becomes ready
[   15.330000] br-lan: port 1(eth0.1) entered forwarding state
[   15.340000] br-lan: port 1(eth0.1) entered forwarding state
[   17.340000] br-lan: port 1(eth0.1) entered forwarding state
[   18.020000] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
[   18.130000] jffs2_build_filesystem(): unlocking the mtd device... done.
[   18.140000] jffs2_build_filesystem(): erasing all blocks after the end marker... done.
[   60.020000] jffs2: notice: (792) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
procd: - init complete -
... done.

[  347.380000] rt305x-esw 10110000.esw: link changed 0x08
[  380.170000] rt305x-esw 10110000.esw: link changed 0x08
[  385.890000] rt305x-esw 10110000.esw: link changed 0x08
[  442.520000] rt305x-esw 10110000.esw: link changed 0x08
[  460.120000] rt305x-esw 10110000.esw: link changed 0x08
[  562.380000] rt305x-esw 10110000.esw: link changed 0x08
[  566.190000] rt305x-esw 10110000.esw: link changed 0x08
[  573.610000] rt305x-esw 10110000.esw: link changed 0x08

After the router reboot,will not back to openwrt again. it will reboot,reboot,reboot.......

U-Boot 1.1.3 (Nov  7 2008 - 00:24:27)

Board: Ralink APSoC DRAM:  32 MB
relocate_code Pointer at: 81fa0000
=====config_usbotg =====
flash_protect ON: from 0xBF000000 to 0xBF02F0F7
protect on 0
protect on 1
protect on 2
protect on 3
protect on 4
protect on 5
protect on 6
protect on 7
protect on 8
protect on 9
flash_protect ON: from 0xBF030000 to 0xBF03FFFF
protect on 10
============================================ 
Ralink UBoot Version: 3.2
-------------------------------------------- 
ASIC 3052_MP2 (Port5<->GigaSW)
DRAM COMPONENT: 128Mbits 
DRAM BUS: 32BIT 
Total memory: 32 MBytes
Date:Nov  7 2008  Time:00:24:27
============================================ 
icache: sets:256, ways:4, linesz:32 ,total:32768
dcache: sets:128, ways:4, linesz:32 ,total:16384 

 ##### The CPU freq = 384 MHZ #### 

 SDRAM bus set to 32 bit 
 SDRAM size =32 Mbytes

Please choose the operation: 
   1: Load system code to SDRAM via TFTP. 
   2: Load system code then write to Flash via TFTP. 
   3: Boot system code via Flash (default).
   4: Entr boot command line interface.
   9: Load Boot Loader code then write to Flash via TFTP. 
 0 
   
3: System Boot system code via Flash.
## Booting image at bf050000 ...
   Image Name:   MIPS OpenWrt Linux-3.10.15
   Created:      2013-10-16   2:11:12 UTC

 System Control Status = 0x30440000 
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    1013258 Bytes = 989.5 kB
   Load Address: 80000000
   Entry Point:  80000000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80000000) ...
## Giving linux memsize in MB, 32

Starting kernel ...

[    0.000000] Linux version 3.10.15 (openwrt@huchra) (gcc version 4.6.4 (OpenWrt/Linaro GCC 4.6-2013.05 r38413) ) #1 Tue Oct 15 19:09:38 PDT 2013
[    0.000000] SoC Type: Ralink RT3052 id:1 rev:3
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU revision is: 0001964c (MIPS 24KEc)
[    0.000000] MIPS: machine is Belkin F5D8235 v2
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 02000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x00000000-0x01ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x00000000-0x01ffffff]
[    0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 32 bytes
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 8128
[    0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2
[    0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
[    0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] Writing ErrCtl register=00029c2b
[    0.000000] Readback ErrCtl register=00029c2b
[    0.000000] Memory: 29224k/32768k available (2237k kernel code, 3544k reserved, 549k data, 220k init, 0k highmem)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS:128
[    0.000000] CPU Clock: 384MHz
[    0.000000] Calibrating delay loop... 255.59 BogoMIPS (lpj=1277952)
[    0.070000] pid_max: default: 32768 minimum: 301
[    0.080000] Mount-cache hash table entries: 512
[    0.090000] pinctrl core: initialized pinctrl subsystem
[    0.100000] NET: Registered protocol family 16
[    0.130000] bio: create slab <bio-0> at 0
[    0.140000] rt2880_gpio 10000600.gpio: registering 24 gpios
[    0.150000] rt2880_gpio 10000600.gpio: registering 24 irq handlers
[    0.160000] Switching to clocksource MIPS
[    0.170000] NET: Registered protocol family 2
[    0.180000] TCP established hash table entries: 512 (order: 0, 4096 bytes)
[    0.190000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)
[    0.210000] TCP: Hash tables configured (established 512 bind 512)
[    0.220000] TCP: reno registered
[    0.230000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.240000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.250000] NET: Registered protocol family 1
[    0.260000] rt-timer 10000100.timer: maximum frequncy is 7812Hz
[    0.300000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.310000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.330000] msgmni has been set to 57
[    0.340000] io scheduler noop registered
[    0.350000] io scheduler deadline registered (default)
[    0.360000] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[    0.380000] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20) is a 16550A
[    0.400000] console [ttyS0] enabled, bootconsole disabled
[    0.400000] console [ttyS0] enabled, bootconsole disabled
[    0.430000] 1f000000.cfi: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x0022cb
[    0.450000] Amd/Fujitsu Extended Query Table at 0x0040
[    0.460000]   Amd/Fujitsu Extended Query version 1.1.
[    0.470000] number of CFI chips: 1
[    0.470000] 4 ofpart partitions found on MTD device 1f000000.cfi
[    0.490000] Creating 4 MTD partitions on "1f000000.cfi":
[    0.500000] 0x000000000000-0x000000050000 : "u-boot"
[    0.510000] 0x000000050000-0x0000007e0000 : "firmware"
[    0.520000] 0x00000014764a-0x0000007e0000 : "rootfs"
[    0.530000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    0.560000] mtd: partition "rootfs" set to be root filesystem
[    0.570000] mtd: partition "rootfs_data" created automatically, ofs=0x2f0000, len=0x4f0000
[    0.590000] 0x0000002f0000-0x0000007e0000 : "rootfs_data"
[    0.600000] 0x0000007e0000-0x0000007f0000 : "nvram"
[    0.610000] 0x0000007f0000-0x000000800000 : "factory"
[    0.630000] eth0: done loading
[    0.640000] rt2880_wdt 10000120.watchdog: Initialized
[    0.650000] TCP: cubic registered
[    0.660000] NET: Registered protocol family 17
[    0.670000] Bridge firewalling registered
[    0.680000] 8021q: 802.1Q VLAN Support v1.8
[    0.690000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[    0.710000] Freeing unused kernel memory: 220K (802b9000 - 802f0000)


U-Boot 1.1.3 (Nov  7 2008 - 00:24:27)

Board: Ralink APSoC DRAM:  32 MB
relocate_code Pointer at: 81fa0000
=====config_usbotg =====
flash_protect ON: from 0xBF000000 to 0xBF02F0F7
protect on 0
protect on 1
protect on 2
protect on 3
protect on 4
protect on 5
protect on 6
protect on 7
protect on 8
protect on 9
flash_protect ON: from 0xBF030000 to 0xBF03FFFF
protect on 10
============================================ 
Ralink UBoot Version: 3.2
-------------------------------------------- 
ASIC 3052_MP2 (Port5<->GigaSW)
DRAM COMPONENT: 128Mbits 
DRAM BUS: 32BIT 
Total memory: 32 MBytes
Date:Nov  7 2008  Time:00:24:27
============================================ 
icache: sets:256, ways:4, linesz:32 ,total:32768
dcache: sets:128, ways:4, linesz:32 ,total:16384 

 ##### The CPU freq = 384 MHZ #### 

 SDRAM bus set to 32 bit 
 SDRAM size =32 Mbytes

Please choose the operation: 
   1: Load system code to SDRAM via TFTP. 
   2: Load system code then write to Flash via TFTP. 
   3: Boot system code via Flash (default).
   4: Entr boot command line interface.
   9: Load Boot Loader code then write to Flash via TFTP. 
 0 
   
3: System Boot system code via Flash.
## Booting image at bf050000 ...
   Image Name:   MIPS OpenWrt Linux-3.10.15
   Created:      2013-10-16   2:11:12 UTC

 System Control Status = 0x30440000 
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    1013258 Bytes = 989.5 kB
   Load Address: 80000000
   Entry Point:  80000000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80000000) ...
## Giving linux memsize in MB, 32

Starting kernel ...

[    0.000000] Linux version 3.10.15 (openwrt@huchra) (gcc version 4.6.4 (OpenWrt/Linaro GCC 4.6-2013.05 r38413) ) #1 Tue Oct 15 19:09:38 PDT 2013
[    0.000000] SoC Type: Ralink RT3052 id:1 rev:3
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU revision is: 0001964c (MIPS 24KEc)
[    0.000000] MIPS: machine is Belkin F5D8235 v2
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 02000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x00000000-0x01ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x00000000-0x01ffffff]
[    0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 32 bytes
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 8128
[    0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2
[    0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
[    0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] Writing ErrCtl register=00029c20
[    0.000000] Readback ErrCtl register=00029c20
[    0.000000] Memory: 29224k/32768k available (2237k kernel code, 3544k reserved, 549k data, 220k init, 0k highmem)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS:128
[    0.000000] CPU Clock: 384MHz
[    0.000000] Calibrating delay loop... 255.59 BogoMIPS (lpj=1277952)
[    0.070000] pid_max: default: 32768 minimum: 301
[    0.080000] Mount-cache hash table entries: 512
[    0.090000] pinctrl core: initialized pinctrl subsystem
[    0.100000] NET: Registered protocol family 16
[    0.130000] bio: create slab <bio-0> at 0
[    0.140000] rt2880_gpio 10000600.gpio: registering 24 gpios
[    0.150000] rt2880_gpio 10000600.gpio: registering 24 irq handlers
[    0.160000] Switching to clocksource MIPS
[    0.170000] NET: Registered protocol family 2
[    0.180000] TCP established hash table entries: 512 (order: 0, 4096 bytes)
[    0.190000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)
[    0.210000] TCP: Hash tables configured (established 512 bind 512)
[    0.220000] TCP: reno registered
[    0.230000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.240000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.250000] NET: Registered protocol family 1
[    0.260000] rt-timer 10000100.timer: maximum frequncy is 7812Hz
[    0.300000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.310000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.330000] msgmni has been set to 57
[    0.340000] io scheduler noop registered
[    0.350000] io scheduler deadline registered (default)
[    0.360000] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[    0.380000] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20) is a 16550A
[    0.400000] console [ttyS0] enabled, bootconsole disabled
[    0.400000] console [ttyS0] enabled, bootconsole disabled
[    0.430000] 1f000000.cfi: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x0022cb
[    0.450000] Amd/Fujitsu Extended Query Table at 0x0040
[    0.460000]   Amd/Fujitsu Extended Query version 1.1.
[    0.470000] number of CFI chips: 1
[    0.470000] 4 ofpart partitions found on MTD device 1f000000.cfi
[    0.490000] Creating 4 MTD partitions on "1f000000.cfi":
[    0.500000] 0x000000000000-0x000000050000 : "u-boot"
[    0.510000] 0x000000050000-0x0000007e0000 : "firmware"
[    0.520000] 0x00000014764a-0x0000007e0000 : "rootfs"
[    0.530000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    0.560000] mtd: partition "rootfs" set to be root filesystem
[    0.570000] mtd: partition "rootfs_data" created automatically, ofs=0x2f0000, len=0x4f0000
[    0.590000] 0x0000002f0000-0x0000007e0000 : "rootfs_data"
[    0.600000] 0x0000007e0000-0x0000007f0000 : "nvram"
[    0.610000] 0x0000007f0000-0x000000800000 : "factory"
[    0.630000] eth0: done loading
[    0.640000] rt2880_wdt 10000120.watchdog: Initialized
[    0.650000] TCP: cubic registered
[    0.660000] NET: Registered protocol family 17
[    0.670000] Bridge firewalling registered
[    0.680000] 8021q: 802.1Q VLAN Support v1.8
[    0.690000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[    0.710000] Freeing unused kernel memory: 220K (802b9000 - 802f0000)


U-Boot 1.1.3 (Nov  7 2008 - 00:24:27)

Board: Ralink APSoC DRAM:  32 MB
relocate_code Pointer at: 81fa0000
=====config_usbotg =====
flash_protect ON: from 0xBF000000 to 0xBF02F0F7
protect on 0
protect on 1
protect on 2
protect on 3
protect on 4
protect on 5
protect on 6
protect on 7
protect on 8
protect on 9
flash_protect ON: from 0xBF030000 to 0xBF03FFFF
protect on 10
============================================ 
Ralink UBoot Version: 3.2
-------------------------------------------- 
ASIC 3052_MP2 (Port5<->GigaSW)
DRAM COMPONENT: 128Mbits 
DRAM BUS: 32BIT 
Total memory: 32 MBytes
Date:Nov  7 2008  Time:00:24:27
============================================ 
icache: sets:256, ways:4, linesz:32 ,total:32768
dcache: sets:128, ways:4, linesz:32 ,total:16384 

 ##### The CPU freq = 384 MHZ #### 

 SDRAM bus set to 32 bit 
 SDRAM size =32 Mbytes

Please choose the operation: 
   1: Load system code to SDRAM via TFTP. 
   2: Load system code then write to Flash via TFTP. 
   3: Boot system code via Flash (default).
   4: Entr boot command line interface.
   9: Load Boot Loader code then write to Flash via TFTP. 
 0 
   
3: System Boot system code via Flash.
## Booting image at bf050000 ...
   Image Name:   MIPS OpenWrt Linux-3.10.15
   Created:      2013-10-16   2:11:12 UTC

 System Control Status = 0x30440000 
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    1013258 Bytes = 989.5 kB
   Load Address: 80000000
   Entry Point:  80000000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80000000) ...
## Giving linux memsize in MB, 32

Starting kernel ...

[    0.000000] Linux version 3.10.15 (openwrt@huchra) (gcc version 4.6.4 (OpenWrt/Linaro GCC 4.6-2013.05 r38413) ) #1 Tue Oct 15 19:09:38 PDT 2013
[    0.000000] SoC Type: Ralink RT3052 id:1 rev:3
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU revision is: 0001964c (MIPS 24KEc)
[    0.000000] MIPS: machine is Belkin F5D8235 v2
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 02000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x00000000-0x01ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x00000000-0x01ffffff]
[    0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 32 bytes
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 8128
[    0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2
[    0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
[    0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] Writing ErrCtl register=00029c28
[    0.000000] Readback ErrCtl register=00029c28
[    0.000000] Memory: 29224k/32768k available (2237k kernel code, 3544k reserved, 549k data, 220k init, 0k highmem)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS:128
[    0.000000] CPU Clock: 384MHz
[    0.000000] Calibrating delay loop... 255.59 BogoMIPS (lpj=1277952)
[    0.070000] pid_max: default: 32768 minimum: 301
[    0.080000] Mount-cache hash table entries: 512
[    0.090000] pinctrl core: initialized pinctrl subsystem
[    0.100000] NET: Registered protocol family 16
[    0.130000] bio: create slab <bio-0> at 0
[    0.140000] rt2880_gpio 10000600.gpio: registering 24 gpios
[    0.150000] rt2880_gpio 10000600.gpio: registering 24 irq handlers
[    0.160000] Switching to clocksource MIPS
[    0.170000] NET: Registered protocol family 2
[    0.180000] TCP established hash table entries: 512 (order: 0, 4096 bytes)
[    0.190000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)
[    0.210000] TCP: Hash tables configured (established 512 bind 512)
[    0.220000] TCP: reno registered
[    0.230000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.240000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.250000] NET: Registered protocol family 1
[    0.260000] rt-timer 10000100.timer: maximum frequncy is 7812Hz
[    0.300000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.310000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.330000] msgmni has been set to 57
[    0.340000] io scheduler noop registered
[    0.350000] io scheduler deadline registered (default)
[    0.360000] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[    0.380000] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20) is a 16550A
[    0.400000] console [ttyS0] enabled, bootconsole disabled
[    0.400000] console [ttyS0] enabled, bootconsole disabled
[    0.430000] 1f000000.cfi: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x0022cb
[    0.450000] Amd/Fujitsu Extended Query Table at 0x0040
[    0.460000]   Amd/Fujitsu Extended Query version 1.1.
[    0.470000] number of CFI chips: 1
[    0.470000] 4 ofpart partitions found on MTD device 1f000000.cfi
[    0.490000] Creating 4 MTD partitions on "1f000000.cfi":
[    0.500000] 0x000000000000-0x000000050000 : "u-boot"
[    0.510000] 0x000000050000-0x0000007e0000 : "firmware"
[    0.520000] 0x00000014764a-0x0000007e0000 : "rootfs"
[    0.530000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    0.560000] mtd: partition "rootfs" set to be root filesystem
[    0.570000] mtd: partition "rootfs_data" created automatically, ofs=0x2f0000, len=0x4f0000
[    0.590000] 0x0000002f0000-0x0000007e0000 : "rootfs_data"
[    0.600000] 0x0000007e0000-0x0000007f0000 : "nvram"
[    0.610000] 0x0000007f0000-0x000000800000 : "factory"
[    0.630000] eth0: done loading
[    0.640000] rt2880_wdt 10000120.watchdog: Initialized
[    0.650000] TCP: cubic registered
[    0.660000] NET: Registered protocol family 17
[    0.670000] Bridge firewalling registered
[    0.680000] 8021q: 802.1Q VLAN Support v1.8
[    0.690000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[    0.710000] Freeing unused kernel memory: 220K (802b9000 - 802f0000)

Attachments (2)

uboot.bin (320.0 KB) - added by Davidwei 4 years ago.
bootloop.cap (13.2 KB) - added by anonymous 3 years ago.
Bootloop openwrt15.05rc1 Linux version 3.18.11 ralink RT3052

Download all attachments as: .zip

Change History (6)

Changed 4 years ago by Davidwei

comment:1 Changed 4 years ago by Davidwei

the attached file is the factory uboot which i backup in openwrt.

comment:2 Changed 4 years ago by Davidwei

any news

comment:3 Changed 4 years ago by anonymous

Any news?

comment:4 Changed 3 years ago by computersforpeace

Not news, exactly, but I see the same thing here when testing both trunk and Barrier Breaker (14.07-rc3).

Changed 3 years ago by anonymous

Bootloop openwrt15.05rc1 Linux version 3.18.11 ralink RT3052

Add Comment

Modify Ticket

Action
as new .
Author


E-mail address and user name can be saved in the Preferences.

 
Note: See TracTickets for help on using tickets.