Modify

Opened 5 years ago

Closed 5 years ago

#13755 closed defect (fixed)

Trunk broken via procd maybe?

Reported by: dani@… Owned by: developers
Priority: high Milestone: Chaos Calmer 15.05
Component: base system Version: Trunk
Keywords: Cc:

Description

Hello,
just flashed latest trunk (r37031) on my tp-link wr740n v2.3 and after boot:

..

VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
Freeing unused kernel memory: 212k freed
procd: Console is alive
procd: - preinit -
sh: write error: Invalid argument
Press the [f] key and hit [enter] to enter failsafe mode

  • failsafe -

sh: write error: Invalid argument

BusyBox v1.19.4 (2013-06-24 23:36:25 EEST) built-in shell (ash)
Enter 'help' for a list of built-in commands.

ash: can't access tty; job control turned off

_

| |.-----.-----.-----.| | | |.----.| |_

| - |_
_ | -| | | _ _|
|_||| ||

|| W I R E L E S S F R E E D O M

-----------------------------------------------------
BARRIER BREAKER (Bleeding Edge, r37031)
-----------------------------------------------------

root@(none):/# df -h
Filesystem Size Used Available Use% Mounted on
rootfs 2.3M 2.3M 0 100% /
/dev/root 2.3M 2.3M 0 100% /
tmpfs 14.5M 12.0K 14.4M 0% /tmp
tmpfs 512.0K 0 512.0K 0% /dev

Attachments (0)

Change History (5)

comment:1 Changed 5 years ago by dani@…

U-Boot 1.1.4 (Sep 3 2010 - 12:28:13)

AP91 (ar7240) U-boot
DRAM:
sri
#### TAP VALUE 1 = 9, 2 = a
32 MB
id read 0x100000ff
flash size 4194304, sector count = 64
Flash: 4 MB
Using default environment

In: serial
Out: serial
Err: serial
Net: ag7240_enet_initialize...
No valid address in Flash. Using fixed address
: cfg1 0xf cfg2 0x7014
eth0: 00:03:7f:09:0b:ad
eth0 up
No valid address in Flash. Using fixed address
: cfg1 0xf cfg2 0x7214
eth1: 00:03:7f:09:0b:ad
ATHRS26: resetting s26
ATHRS26: s26 reset done
eth1 up
eth0, eth1
Autobooting in 1 seconds
## Booting image at 9f020000 ...

Uncompressing Kernel Image ... OK

Starting kernel ...

OpenWrt kernel loader for AR7XXX/AR9XXX
Copyright (C) 2011 Gabor Juhos <juhosg@…>
Looking for OpenWrt image... found at 0xbf022000
Decompressing kernel... done!
Starting kernel at 80060000...

Linux version 3.8.13 (dani@x61) (gcc version 4.6.4 (OpenWrt/Linaro GCC 4.6-2012.12 r37033) ) #2 Wed Jun 26 00:27:20 EEST 2013
bootconsole [early0] enabled
CPU revision is: 00019374 (MIPS 24Kc)
SoC: Atheros AR7240 rev 2
Clocks: CPU:350.000MHz, DDR:350.000MHz, AHB:175.000MHz, Ref:5.000MHz
Determined physical RAM map:

memory: 02000000 @ 00000000 (usable)

Zone ranges:

Normal [mem 0x00000000-0x01ffffff]

Movable zone start for each node
Early memory node ranges

node 0: [mem 0x00000000-0x01ffffff]

Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128
Kernel command line: board=TL-WR741ND console=ttyS0,115200 rootfstype=squashfs,jffs2 noinitrd
PID hash table entries: 128 (order: -3, 512 bytes)
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
ex_table already sorted, skipping sort
Writing ErrCtl register=00000000
Readback ErrCtl register=00000000
Memory: 29388k/32768k available (1963k kernel code, 3380k reserved, 317k data, 212k init, 0k highmem)
SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
NR_IRQS:51
Calibrating delay loop... 232.24 BogoMIPS (lpj=1161216)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
NET: Registered protocol family 16
MIPS: machine is TP-LINK TL-WR741ND
registering PCI controller with io_map_base unset
bio: create slab <bio-0> at 0
PCI host bridge to bus 0000:00
pci_bus 0000:00: root bus resource [mem 0x10000000-0x13ffffff]
pci_bus 0000:00: root bus resource [io 0x0000]
pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
pci 0000:00:00.0: fixup device configuration
pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x1000ffff 64bit]
pci 0000:00:00.0: using irq 40 for pin 1
Switching to clocksource MIPS
NET: Registered protocol family 2
TCP established hash table entries: 512 (order: 0, 4096 bytes)
TCP bind hash table entries: 512 (order: -1, 2048 bytes)
TCP: Hash tables configured (established 512 bind 512)
TCP: reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
squashfs: version 4.0 (2009/01/31) Phillip Lougher
jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
msgmni has been set to 57
io scheduler noop registered
io scheduler deadline registered (default)
Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A
console [ttyS0] enabled, bootconsole disabled
console [ttyS0] enabled, bootconsole disabled
ath79-spi ath79-spi: master is unqueued, this is deprecated
m25p80 spi0.0: found s25sl032p, expected m25p80
m25p80 spi0.0: s25sl032p (4096 Kbytes)
5 tp-link partitions found on MTD device spi0.0
Creating 5 MTD partitions on "spi0.0":
0x000000000000-0x000000020000 : "u-boot"
0x000000020000-0x0000000eb800 : "kernel"
mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
0x0000000eb800-0x0000003f0000 : "rootfs"
mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
mtd: partition "rootfs" set to be root filesystem
mtd: partition "rootfs_data" created automatically, ofs=320000, len=D0000
0x000000320000-0x0000003f0000 : "rootfs_data"
0x0000003f0000-0x000000400000 : "art"
0x000000020000-0x0000003f0000 : "firmware"
libphy: ag71xx_mdio: probed
eth0: Atheros AG71xx at 0xba000000, irq 5, mode:GMII
eth0: Found an AR7240/AR9330 built-in switch
eth1: Atheros AG71xx at 0xb9000000, irq 4, mode:MII
ag71xx ag71xx.0 eth1: connected to PHY at ag71xx-mdio.0:04 [uid=004dd041, driver=Generic PHY]
TCP: cubic registered
NET: Registered protocol family 17
8021q: 802.1Q VLAN Support v1.8
VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
Freeing unused kernel memory: 212k freed
procd: Console is alive
procd: - preinit -
sh: write error: Invalid argument
Press the [f] key and hit [enter] to enter failsafe mode
eth0: link up (1000Mbps/Full duplex)

  • failsafe -

sh: write error: Invalid argument

BusyBox v1.19.4 (2013-06-26 00:20:19 EEST) built-in shell (ash)
Enter 'help' for a list of built-in commands.

ash: can't access tty; job control turned off

_

| |.-----.-----.-----.| | | |.----.| |_

| - |_
_ | -| | | _ _|
|_||| ||

|| W I R E L E S S F R E E D O M

-----------------------------------------------------
BARRIER BREAKER (Bleeding Edge, r37033)
-----------------------------------------------------

root@(none):/#

comment:2 Changed 5 years ago by dani@…

root@(none):/# ps

PID USER VSZ STAT COMMAND

1 root 1072 S /sbin/init
2 root 0 SW [kthreadd]
3 root 0 SW [ksoftirqd/0]
4 root 0 SW [kworker/0:0]
5 root 0 SW< [kworker/0:0H]
6 root 0 SW [kworker/u:0]
7 root 0 SW< [kworker/u:0H]
8 root 0 SW< [khelper]
9 root 0 SW [kworker/u:1]

68 root 0 SW [bdi-default]
70 root 0 SW< [kblockd]

100 root 0 SW [kswapd0]
144 root 0 SW [fsnotify_mark]
157 root 0 SW< [ath79-spi]
219 root 0 SW< [deferwq]
220 root 0 SW [kworker/0:1]
221 root 0 SW [kworker/0:2]
237 root 1408 S /bin/sh /etc/preinit
290 root 1276 S telnetd -l /bin/login.sh
292 root 1272 S lock /tmp/.failsafe
293 root 1284 S ash --login
300 root 1280 R ps

root@(none):/#

if i do kill -9 237 the router will continue to boot normally..

root@(none):/# kill -9 237
root@(none):/# procd: - early -
procd: - init -
procd: Killing existing ubus instance, pid=420
procd: Killing existing ubus instance, pid=421
procd: Killing existing ubus instance, pid=422
Please press Enter to activate this console.
Loading modules backported from Linux version master-2013-06-13-0-g09fcdfb
Backport generated by backports.git backports-20130531-13-g3d933eb
cfg80211: Calling CRDA to update world regulatory domain
cfg80211: World regulatory domain updated:
cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
NET: Registered protocol family 10
zsmalloc: module is from the staging directory, the quality is unknown, you have been warned.
zram: module is from the staging directory, the quality is unknown, you have been warned.
zram: num_devices not specified. Using default: 1
zram: Creating 1 devices ...
PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
cfg80211: Calling CRDA for country: US
cfg80211: Regulatory domain changed to country: US
cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)
cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211: (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211: (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)
ieee80211 phy0: Atheros AR9285 Rev:2 mem=0xb0000000, irq=40
PPP generic driver version 2.4.2
gre: GRE over IPv4 demultiplexor driver
ip_gre: GRE over IPv4 tunneling driver
ip_tables: (C) 2000-2006 Netfilter Core Team
xt_time: kernel timezone is -0000
NET: Registered protocol family 24
nf_conntrack version 0.5.0 (462 buckets, 1848 max)
PPTP driver version 0.8.5
ip6_tables: (C) 2000-2006 Netfilter Core Team
u32 classifier

Performance counters on
input device check on
Actions configured

Mirror/redirect action on
Adding 14332k swap on /dev/zram0. Priority:-1 extents:1 across:14332k SS
eth0: link down
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
device eth0 entered promiscuous mode
IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
eth0: link up (1000Mbps/Full duplex)
br-lan: port 1(eth0) entered forwarding state
br-lan: port 1(eth0) entered forwarding state
IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
br-lan: port 1(eth0) entered forwarding state
IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
device wlan0 entered promiscuous mode
IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
br-lan: port 2(wlan0) entered forwarding state
br-lan: port 2(wlan0) entered forwarding state
IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
br-lan: port 2(wlan0) entered forwarding state
device wlan0 left promiscuous mode
br-lan: port 2(wlan0) entered disabled state
IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
device wlan0 entered promiscuous mode
IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
br-lan: port 2(wlan0) entered forwarding state
br-lan: port 2(wlan0) entered forwarding state
IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready

BusyBox v1.19.4 (2013-06-26 00:20:19 EEST) built-in shell (ash)
Enter 'help' for a list of built-in commands.

_

| |.-----.-----.-----.| | | |.----.| |_

| - |_
_ | -| | | _ _|
|_||| ||

|| W I R E L E S S F R E E D O M

-----------------------------------------------------
BARRIER BREAKER (Bleeding Edge, r37033)
-----------------------------------------------------

@wr740n:/# br-lan: port 2(wlan0) entered forwarding state
procd: - init complete -
IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready

comment:3 Changed 5 years ago by Elphidium

same here on wl500gp v1 and mr3220 v1 on r37035

comment:4 Changed 5 years ago by dani@…

as per blogic's advice i compiled without CONFIG_PACKAGE_kmod-gpio-button-hotplug and the router starts as it should (almost.. see attached below log) :

Starting kernel ...

OpenWrt kernel loader for AR7XXX/AR9XXX
Copyright (C) 2011 Gabor Juhos <juhosg@…>
Looking for OpenWrt image... found at 0xbf022000
Decompressing kernel... done!
Starting kernel at 80060000...

Linux version 3.8.13 (dani@x61) (gcc version 4.6.4 (OpenWrt/Linaro GCC 4.6-2012.12 r37033) ) #4 Fri Jun 28 15:08:03 EEST 2013
bootconsole [early0] enabled
CPU revision is: 00019374 (MIPS 24Kc)
SoC: Atheros AR7240 rev 2
Clocks: CPU:350.000MHz, DDR:350.000MHz, AHB:175.000MHz, Ref:5.000MHz
Determined physical RAM map:

memory: 02000000 @ 00000000 (usable)

Zone ranges:

Normal [mem 0x00000000-0x01ffffff]

Movable zone start for each node
Early memory node ranges

node 0: [mem 0x00000000-0x01ffffff]

Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128
Kernel command line: board=TL-WR741ND console=ttyS0,115200 rootfstype=squashfs,jffs2 noinitrd
PID hash table entries: 128 (order: -3, 512 bytes)
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
ex_table already sorted, skipping sort
Writing ErrCtl register=00000000
Readback ErrCtl register=00000000
Memory: 29388k/32768k available (1963k kernel code, 3380k reserved, 318k data, 212k init, 0k highmem)
SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
NR_IRQS:51
Calibrating delay loop... 232.24 BogoMIPS (lpj=1161216)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
NET: Registered protocol family 16
MIPS: machine is TP-LINK TL-WR741ND
registering PCI controller with io_map_base unset
bio: create slab <bio-0> at 0
PCI host bridge to bus 0000:00
pci_bus 0000:00: root bus resource [mem 0x10000000-0x13ffffff]
pci_bus 0000:00: root bus resource [io 0x0000]
pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
pci 0000:00:00.0: fixup device configuration
pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x1000ffff 64bit]
pci 0000:00:00.0: using irq 40 for pin 1
Switching to clocksource MIPS
NET: Registered protocol family 2
TCP established hash table entries: 512 (order: 0, 4096 bytes)
TCP bind hash table entries: 512 (order: -1, 2048 bytes)
TCP: Hash tables configured (established 512 bind 512)
TCP: reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
squashfs: version 4.0 (2009/01/31) Phillip Lougher
jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
msgmni has been set to 57
io scheduler noop registered
io scheduler deadline registered (default)
Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A
console [ttyS0] enabled, bootconsole disabled
console [ttyS0] enabled, bootconsole disabled
ath79-spi ath79-spi: master is unqueued, this is deprecated
m25p80 spi0.0: found s25sl032p, expected m25p80
m25p80 spi0.0: s25sl032p (4096 Kbytes)
5 tp-link partitions found on MTD device spi0.0
Creating 5 MTD partitions on "spi0.0":
0x000000000000-0x000000020000 : "u-boot"
0x000000020000-0x0000000eb800 : "kernel"
mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
0x0000000eb800-0x0000003f0000 : "rootfs"
mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
mtd: partition "rootfs" set to be root filesystem
mtd: partition "rootfs_data" created automatically, ofs=320000, len=D0000
0x000000320000-0x0000003f0000 : "rootfs_data"
0x0000003f0000-0x000000400000 : "art"
0x000000020000-0x0000003f0000 : "firmware"
libphy: ag71xx_mdio: probed
eth0: Atheros AG71xx at 0xba000000, irq 5, mode:GMII
eth0: Found an AR7240/AR9330 built-in switch
eth1: Atheros AG71xx at 0xb9000000, irq 4, mode:MII
ag71xx ag71xx.0 eth1: connected to PHY at ag71xx-mdio.0:04 [uid=004dd041, driver=Generic PHY]
TCP: cubic registered
NET: Registered protocol family 17
8021q: 802.1Q VLAN Support v1.8
VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
Freeing unused kernel memory: 212k freed
procd: Console is alive
procd: - preinit -
sh: write error: Invalid argument
Press the [f] key and hit [enter] to enter failsafe mode
sh: write error: Invalid argument
mount_root: jffs2 is ready
jffs2: notice: (284) jffs2_build_xattr_subsystem: complete building xattr subsystem, 3 of xdatum (0 unchecked, 2 orphan) and 2.
procd: - early -
procd: - init -
Please press Enter to activate this console.
Loading modules backported from Linux version master-2013-06-13-0-g09fcdfb
Backport generated by backports.git backports-20130531-13-g3d933eb
cfg80211: Calling CRDA to update world regulatory domain
cfg80211: World regulatory domain updated:
cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
NET: Registered protocol family 10
zsmalloc: module is from the staging directory, the quality is unknown, you have been warned.
zram: module is from the staging directory, the quality is unknown, you have been warned.
zram: num_devices not specified. Using default: 1
zram: Creating 1 devices ...
PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
cfg80211: Calling CRDA for country: US
cfg80211: Regulatory domain changed to country: US
cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)
cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211: (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211: (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)
ieee80211 phy0: Atheros AR9285 Rev:2 mem=0xb0000000, irq=40
PPP generic driver version 2.4.2
gre: GRE over IPv4 demultiplexor driver
ip_gre: GRE over IPv4 tunneling driver
ip_tables: (C) 2000-2006 Netfilter Core Team
xt_time: kernel timezone is -0000
NET: Registered protocol family 24
nf_conntrack version 0.5.0 (462 buckets, 1848 max)
PPTP driver version 0.8.5
ip6_tables: (C) 2000-2006 Netfilter Core Team
u32 classifier

Performance counters on
input device check on
Actions configured

Mirror/redirect action on
Adding 14332k swap on /dev/zram0. Priority:-1 extents:1 across:14332k SS
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
device eth0 entered promiscuous mode
IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
eth1: link up (100Mbps/Full duplex)
IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
device wlan0 entered promiscuous mode
IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
br-lan: port 2(wlan0) entered forwarding state
br-lan: port 2(wlan0) entered forwarding state
IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
br-lan: port 2(wlan0) entered forwarding state
procd: - init complete -

BusyBox v1.19.4 (2013-06-28 14:54:54 EEST) built-in shell (ash)
Enter 'help' for a list of built-in commands.

_

| |.-----.-----.-----.| | | |.----.| |_

| - |_
_ | -| | | _ _|
|_||| ||

|| W I R E L E S S F R E E D O M

-----------------------------------------------------
BARRIER BREAKER (Bleeding Edge, r37076)
-----------------------------------------------------

root@wr740n:/#

comment:5 Changed 5 years ago by nbd

  • Resolution set to fixed
  • Status changed from new to closed

fixed in r37090

Add Comment

Modify Ticket

Action
as closed .
The resolution will be deleted. Next status will be 'reopened'.
Author


E-mail address and user name can be saved in the Preferences.

 
Note: See TracTickets for help on using tickets.