Modify

Opened 5 years ago

Closed 4 years ago

#13256 closed defect (fixed)

Buffalo WBMR-HP-G300H endless reboot

Reported by: d.buffa@… Owned by: developers
Priority: highest Milestone: Chaos Calmer 15.05
Component: base system Version: Trunk
Keywords: Cc:

Description (last modified by blogic)

Hi,

I compiled from trunk for my WBMR-HP-G300H, but after flash router reboot continuously.

ARCADYAN U-Boot 1.00 (Nov 10 2010 - 17:41:42)

AR9 BOARD
CLOCK CPU 333M RAM 166M
DRAM:  64 MB

 relocate_code start
 relocate_code finish.
Flash: 32 MB
In:    serial
Out:   serial
Err:   serial
Net:   
switch chip id=00001001
AR8316
amazon_s Switch

Copying boot params.....
DONE

Type "run flash_nfs" to mount root filesystem over NFS

Hit any key to stop autoboot:  3  2  1  0 
## Booting image at b0060000 ...
   Image Name:   MIPS OpenWrt Linux-3.8.3
   Created:      2013-03-27  21:37:18 UTC
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    1207219 Bytes =  1.2 MB
   Load Address: 80002000
   Entry Point:  80002000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80002000) ...
## Giving linux memsize in MB, 64

Starting kernel ...

[    0.000000] Linux version 3.8.3 (daniele@danfedvm.localdomain) (gcc version 4.6.4 20121210 (prerelease) (Linaro GCC 4.6-2012.12) ) #3 Wed Mar 27 22:37:10 CET 2013

[    0.000000] SoC: AR9 rev 1.2

[    0.000000] bootconsole [early0] enabled

[    0.000000] CPU revision is: 0001954c (MIPS 34Kc)

[    0.000000] Determined physical RAM map:

[    0.000000]  memory: 04000000 @ 00000000 (usable)

[    0.000000] Initrd not found or empty - disabling initrd

[    0.000000] Zone ranges:

[    0.000000]   Normal   [mem 0x00000000-0x03ffffff]

[    0.000000] Movable zone start for each node

[    0.000000] Early memory node ranges

[    0.000000]   node   0: [mem 0x00000000-0x03ffffff]

[    0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.

[    0.000000] Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 32 bytes

[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256

[    0.000000] Kernel command line: console=ttyLTQ0,115200 init=/etc/preinit

[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)

[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)

[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)

[    0.000000] __ex_table already sorted, skipping sort

[    0.000000] Writing ErrCtl register=000205d0

[    0.000000] Readback ErrCtl register=000205d0

[    0.000000] Memory: 61128k/65536k available (2577k kernel code, 4408k reserved, 785k data, 212k init, 0k highmem)

[    0.000000] NR_IRQS:256

[    0.000000] CPU Clock: 333MHz

[    0.000000] Calibrating delay loop... 221.18 BogoMIPS (lpj=442368)

[    0.040000] pid_max: default: 32768 minimum: 301

[    0.044000] Mount-cache hash table entries: 512

[    0.048000] pinctrl core: initialized pinctrl subsystem

[    0.052000] NET: Registered protocol family 16

[    0.068000] pinctrl-xway 1e100b10.pinmux: Init done

[    0.072000] dma-xway 1e104100.dma: Init done - hw rev: 6, ports: 5, channels: 20

[    0.080000] PCI host bridge /fpi@10000000/pci@E105400 ranges:

[    0.084000]  MEM 0x0000000018000000..0x0000000019ffffff

[    0.088000]   IO 0x000000001ae00000..0x000000001affffff

[    0.108000] bio: create slab <bio-0> at 0

[    0.116000] usbcore: registered new interface driver usbfs

[    0.120000] usbcore: registered new interface driver hub

[    0.124000] usbcore: registered new device driver usb

[    0.128000] PCI host bridge to bus 0000:00

[    0.132000] pci_bus 0000:00: root bus resource [mem 0x18000000-0x19ffffff]

[    0.136000] pci_bus 0000:00: root bus resource [io  0x1ae00000-0x1affffff]

[    0.140000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]

[    0.144000] pci 0000:00:0e.0: BAR 0: assigned [mem 0x18000000-0x1800ffff]

[    0.148000] pci 0000:00:0e.0: SLOT:14 PIN:1 IRQ:30

[    0.152000] Switching to clocksource MIPS

[    0.160000] NET: Registered protocol family 2

[    0.164000] TCP established hash table entries: 512 (order: 0, 4096 bytes)

[    0.172000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)

[    0.180000] TCP: Hash tables configured (established 512 bind 512)

[    0.184000] TCP: reno registered

[    0.188000] UDP hash table entries: 256 (order: 0, 4096 bytes)

[    0.196000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)

[    0.200000] NET: Registered protocol family 1

[    0.204000] gptu: totally 6 16-bit timers/counters

[    0.212000] gptu: misc_register on minor 63

[    0.216000] gptu: succeeded to request irq 126

[    0.220000] gptu: succeeded to request irq 127

[    0.224000] gptu: succeeded to request irq 128

[    0.228000] gptu: succeeded to request irq 129

[    0.232000] gptu: succeeded to request irq 130

[    0.236000] gptu: succeeded to request irq 131

[    0.248000] squashfs: version 4.0 (2009/01/31) Phillip Lougher

[    0.256000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.

[    0.264000] msgmni has been set to 119

[    0.268000] io scheduler noop registered

[    0.272000] io scheduler deadline registered (default)

[    0.280000] 1e100c00.serial: ttyLTQ0 at MMIO 0x1e100c00 (irq = 112) is a lantiq,asc

[    0.288000] console [ttyLTQ0] enabled, bootconsole disabled
[    0.288000] console [ttyLTQ0] enabled, bootconsole disabled

[    0.300000] ltq_nor: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x00227e
[    0.308000] Amd/Fujitsu Extended Query Table at 0x0040
[    0.316000]   Amd/Fujitsu Extended Query version 1.3.
[    0.320000] number of CFI chips: 1
[    0.324000] 5 ofpart partitions found on MTD device ltq_nor
[    0.328000] Creating 5 MTD partitions on "ltq_nor":
[    0.332000] 0x000000000000-0x000000040000 : "uboot"
[    0.340000] 0x000000040000-0x000000060000 : "uboot_env"
[    0.348000] 0x000000060000-0x000001f80000 : "linux"
[    0.352000] found squashfs behind kernel
[    0.356000] Creating 2 MTD partitions on "ltq_nor":
[    0.360000] 0x000000060000-0x000000186bf3 : "kernel"
[    0.364000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    0.380000] 0x000000186bf3-0x000001f80000 : "rootfs"
[    0.384000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    0.400000] mtd: partition "rootfs" set to be root filesystem
[    0.404000] mtd: partition "rootfs_data" created automatically, ofs=5C0000, len=19C0000 
[    0.412000] 0x0000005c0000-0x000001f80000 : "rootfs_data"
[    0.420000] 0x000001fc0000-0x000001fe0000 : "board"
[    0.428000] 0x000001fe0000-0x000002000000 : "calibration"
[    0.468000] switch0: Atheros AR8316 switch registered on 1e180000.etop-ff
[    0.496000] libphy: ltq_mii: probed
[    0.500000] ar8316: Using port 4 as switch port
[    1.608000] eth0: attached PHY [Atheros AR8216/AR8236/AR8316] (phy_addr=1e180000.etop-ff:00, irq=-1)
[    1.616000] wdt 1f8803f0.watchdog: Init done
[    1.624000] leds-gpio gpio-leds.5: pins are not configured from the driver
[    1.636000] TCP: cubic registered
[    1.636000] NET: Registered protocol family 17
[    1.640000] 8021q: 802.1Q VLAN Support v1.8
[    1.652000] VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
[    1.660000] Freeing unused kernel memory: 212k freed
- preinit -
Press the [f] key and hit [enter] to enter failsafe mode
- regular preinit -
jffs2 not ready yet; using ramdisk
- init -

Please press Enter to activate this console. [   10.456000] Compat-drivers backport release: compat-drivers-2013-01-21-1
[   10.464000] Backport based on wireless-testing.git master-2013-02-22
[   10.468000] compat.git: wireless-testing.git
[   10.672000] cfg80211: Calling CRDA to update world regulatory domain
[   10.676000] cfg80211: World regulatory domain updated:
[   10.680000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[   10.688000] cfg80211:   (2402000 KHz - 2494000 KHz @ 40000 KHz), (500 mBi, 3000 mBm)
[   10.696000] cfg80211:   (4910000 KHz - 5835000 KHz @ 40000 KHz), (N/A, 3000 mBm)
[   11.596000] PCI: Enabling device 0000:00:0e.0 (0000 -> 0002)
[   13.176000] ieee80211 phy0: Atheros AR9280 Rev:2 mem=0xb8000000, irq=30
[   13.188000] cfg80211: Calling CRDA for country: US
[   13.188000] cfg80211: Regulatory domain changed to country: US
[   13.196000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[   13.204000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
[   13.212000] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)
[   13.220000] cfg80211:   (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   13.228000] cfg80211:   (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   13.236000] cfg80211:   (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   13.244000] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)
[   13.272000] NET: Registered protocol family 8
[   13.276000] NET: Registered protocol family 20
[   14.428000] PPP generic driver version 2.4.2
[   14.468000] tun: Universal TUN/TAP device driver, 1.6
[   14.472000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[   14.672000] ip_tables: (C) 2000-2006 Netfilter Core Team
[   14.864000] NET: Registered protocol family 24
[   15.020000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[   15.044000] ehci-platform: EHCI generic platform driver
[   15.072000] nf_conntrack version 0.5.0 (958 buckets, 3832 max)
[   16.016000] xt_time: kernel timezone is -0000
[   17.732000] IFX MEI Version 5.00.00
[   17.996000] IFXUSB: ifxusb_hcd: version 3.2 B110801
[   18.500000] IFXUSB: USB core #0 soft-reset
[   18.704000] IFXUSB: USB core #0 soft-reset
[   18.708000] ifxusb_hcd ifxusb_hcd: IFX USB Controller
[   18.712000] ifxusb_hcd ifxusb_hcd: new USB bus registered, assigned bus number 1
[   18.720000] ifxusb_hcd ifxusb_hcd: irq 62, io mem 0xbe101000
[   18.724000] IFXUSB: Init: Power Port (0)
[   18.728000] hub 1-0:1.0: USB hub found
[   18.732000] hub 1-0:1.0: 1 port detected
[   18.736000] ifxusb_hcd ifxusb_hcd: requested GPIO 236
[   18.900000] Infineon CPE API Driver version: DSL CPE API V3.24.4.4
[   19.280000] ATM1.0.26    ATM (A1) firmware version 0.16
[   19.284000] ifxmips_atm: ATM init succeed
[   21.640000]þXR9-x chip found
DDR set @ 166.6MHz
Check initial DDR setting...DDR check ok... start booting...



ARCADYAN U-Boot 1.00 (Nov 10 2010 - 17:41:42)

AR9 BOARD
CLOCK CPU 333M RAM 166M
DRAM:  64 MB

 relocate_code start
 relocate_code finish.
Flash: 32 MB
In:    serial
Out:   serial
Err:   serial
Net:   
switch chip id=00001001
AR8316
amazon_s Switch

Copying boot params.....
DONE

Type "run flash_nfs" to mount root filesystem over NFS

Hit any key to stop autoboot:  3  2  1  0 
## Booting image at b0060000 ...
   Image Name:   MIPS OpenWrt Linux-3.8.3
   Created:      2013-03-27  21:37:18 UTC
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    1207219 Bytes =  1.2 MB
   Load Address: 80002000
   Entry Point:  80002000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80002000) ...
## Giving linux memsize in MB, 64

Starting kernel ...

[    0.000000] Linux version 3.8.3 (daniele@danfedvm.localdomain) (gcc version 4.6.4 20121210 (prerelease) (Linaro GCC 4.6-2012.12) ) #3 Wed Mar 27 22:37:10 CET 2013

[    0.000000] SoC: AR9 rev 1.2

[    0.000000] bootconsole [early0] enabled

[    0.000000] CPU revision is: 0001954c (MIPS 34Kc)

[    0.000000] Determined physical RAM map:

[    0.000000]  memory: 04000000 @ 00000000 (usable)
.............

and so on, endless.

I hope in a fix

Thanks in advance
Daniele Buffa.

Attachments (0)

Change History (12)

comment:1 Changed 5 years ago by anonymous

could you please check if your Router does the same if you boot into the failsafe mode?
just press f and enter to enter failsafe when the message appears.

could be the same problem we are seeing on other lantiq devices.
/ticket/12642.html

comment:2 Changed 5 years ago by d.buffa@…

failsafe mode works just fine

comment:3 Changed 5 years ago by blogic

  • Description modified (diff)
  • Resolution set to worksforme
  • Status changed from new to closed

there was a problem with the reset button triggering constantly. i just tested latest trunk and the problem does not exist there.

i used r36156 for testing. please check with this or a later revision

comment:4 Changed 5 years ago by d.buffa@…

  • Resolution worksforme deleted
  • Status changed from closed to reopened

Tried with r36193. Same identical behaviour

Upgrade completed
Rebooting system...
[  179.156000] Restarting system.
[  179.156000]üXR9-x chip found
DDR set @ 166.6MHz
Check initial DDR setting...DDR check ok... start booting...



ARCADYAN U-Boot 1.00 (Nov 10 2010 - 17:41:42)

AR9 BOARD
CLOCK CPU 333M RAM 166M
DRAM:  64 MB

 relocate_code start
 relocate_code finish.
Flash: 32 MB
In:    serial
Out:   serial
Err:   serial
Net:   
switch chip id=00001001
AR8316
amazon_s Switch

Copying boot params.....
DONE

Type "run flash_nfs" to mount root filesystem over NFS

Hit any key to stop autoboot:  3  2  1  0 
## Booting image at b0060000 ...
   Image Name:   MIPS OpenWrt Linux-3.8.3
   Created:      2013-04-03  22:13:46 UTC
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    1201861 Bytes =  1.1 MB
   Load Address: 80002000
   Entry Point:  80002000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80002000) ...
## Giving linux memsize in MB, 64

Starting kernel ...

[    0.000000] Linux version 3.8.3 (daniele@danfedvm.localdomain) (gcc version 4.6.4 20121210 (prerelease) (Linaro GCC 4.6-2012.12) ) #4 Thu Apr 4 00:13:38 CEST 2013

[    0.000000] SoC: AR9 rev 1.2

[    0.000000] bootconsole [early0] enabled

[    0.000000] CPU revision is: 0001954c (MIPS 34Kc)

[    0.000000] Determined physical RAM map:

[    0.000000]  memory: 04000000 @ 00000000 (usable)

[    0.000000] Initrd not found or empty - disabling initrd

[    0.000000] Zone ranges:

[    0.000000]   Normal   [mem 0x00000000-0x03ffffff]

[    0.000000] Movable zone start for each node

[    0.000000] Early memory node ranges

[    0.000000]   node   0: [mem 0x00000000-0x03ffffff]

[    0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.

[    0.000000] Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 32 bytes

[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256

[    0.000000] Kernel command line: console=ttyLTQ0,115200 init=/etc/preinit

[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)

[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)

[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)

[    0.000000] __ex_table already sorted, skipping sort

[    0.000000] Writing ErrCtl register=00040020

[    0.000000] Readback ErrCtl register=00040020

[    0.000000] Memory: 61128k/65536k available (2563k kernel code, 4408k reserved, 783k data, 228k init, 0k highmem)

[    0.000000] NR_IRQS:256

[    0.000000] CPU Clock: 333MHz

[    0.000000] Calibrating delay loop... 221.18 BogoMIPS (lpj=442368)

[    0.040000] pid_max: default: 32768 minimum: 301

[    0.044000] Mount-cache hash table entries: 512

[    0.048000] pinctrl core: initialized pinctrl subsystem

[    0.052000] NET: Registered protocol family 16

[    0.068000] pinctrl-xway 1e100b10.pinmux: Init done

[    0.072000] dma-xway 1e104100.dma: Init done - hw rev: 6, ports: 5, channels: 20

[    0.080000] PCI host bridge /fpi@10000000/pci@E105400 ranges:

[    0.084000]  MEM 0x0000000018000000..0x0000000019ffffff

[    0.088000]   IO 0x000000001ae00000..0x000000001affffff

[    0.108000] bio: create slab <bio-0> at 0

[    0.116000] usbcore: registered new interface driver usbfs

[    0.120000] usbcore: registered new interface driver hub

[    0.124000] usbcore: registered new device driver usb

[    0.128000] PCI host bridge to bus 0000:00

[    0.132000] pci_bus 0000:00: root bus resource [mem 0x18000000-0x19ffffff]

[    0.136000] pci_bus 0000:00: root bus resource [io  0x1ae00000-0x1affffff]

[    0.140000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]

[    0.144000] pci 0000:00:0e.0: BAR 0: assigned [mem 0x18000000-0x1800ffff]

[    0.148000] pci 0000:00:0e.0: SLOT:14 PIN:1 IRQ:30

[    0.152000] Switching to clocksource MIPS

[    0.160000] NET: Registered protocol family 2

[    0.164000] TCP established hash table entries: 512 (order: 0, 4096 bytes)

[    0.172000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)

[    0.180000] TCP: Hash tables configured (established 512 bind 512)

[    0.184000] TCP: reno registered

[    0.188000] UDP hash table entries: 256 (order: 0, 4096 bytes)

[    0.196000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)

[    0.200000] NET: Registered protocol family 1

[    0.204000] gptu: totally 6 16-bit timers/counters

[    0.212000] gptu: misc_register on minor 63

[    0.216000] gptu: succeeded to request irq 126

[    0.220000] gptu: succeeded to request irq 127

[    0.224000] gptu: succeeded to request irq 128

[    0.228000] gptu: succeeded to request irq 129

[    0.232000] gptu: succeeded to request irq 130

[    0.236000] gptu: succeeded to request irq 131

[    0.248000] squashfs: version 4.0 (2009/01/31) Phillip Lougher

[    0.256000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.

[    0.264000] msgmni has been set to 119

[    0.268000] io scheduler noop registered

[    0.272000] io scheduler deadline registered (default)

[    0.280000] 1e100c00.serial: ttyLTQ0 at MMIO 0x1e100c00 (irq = 112) is a lantiq,asc

[    0.288000] console [ttyLTQ0] enabled, bootconsole disabled
[    0.288000] console [ttyLTQ0] enabled, bootconsole disabled

[    0.300000] ltq_nor: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x00227e
[    0.308000] Amd/Fujitsu Extended Query Table at 0x0040
[    0.316000]   Amd/Fujitsu Extended Query version 1.3.
[    0.320000] number of CFI chips: 1
[    0.324000] 5 ofpart partitions found on MTD device ltq_nor
[    0.328000] Creating 5 MTD partitions on "ltq_nor":
[    0.332000] 0x000000000000-0x000000040000 : "uboot"
[    0.340000] 0x000000040000-0x000000060000 : "uboot_env"
[    0.348000] 0x000000060000-0x000001f80000 : "linux"
[    0.352000] found squashfs behind kernel
[    0.356000] Creating 2 MTD partitions on "ltq_nor":
[    0.360000] 0x000000060000-0x000000185705 : "kernel"
[    0.364000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    0.380000] 0x000000185705-0x000001f80000 : "rootfs"
[    0.384000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    0.400000] mtd: partition "rootfs" set to be root filesystem
[    0.404000] mtd: partition "rootfs_data" created automatically, ofs=3E0000, len=1BA0000 
[    0.412000] 0x0000003e0000-0x000001f80000 : "rootfs_data"
[    0.420000] 0x000001fc0000-0x000001fe0000 : "board"
[    0.428000] 0x000001fe0000-0x000002000000 : "calibration"
[    0.468000] switch0: Atheros AR8316 switch registered on 1e180000.etop-ff
[    0.496000] libphy: ltq_mii: probed
[    0.500000] ar8316: Using port 4 as switch port
[    1.608000] eth0: attached PHY [Atheros AR8216/AR8236/AR8316] (phy_addr=1e180000.etop-ff:00, irq=-1)
[    1.616000] wdt 1f8803f0.watchdog: Init done
[    1.624000] leds-gpio gpio-leds.5: pins are not configured from the driver
[    1.636000] TCP: cubic registered
[    1.636000] NET: Registered protocol family 17
[    1.640000] 8021q: 802.1Q VLAN Support v1.8
[    1.652000] VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
[    1.660000] Freeing unused kernel memory: 228k freed
- preinit -
Press the [f] key and hit [enter] to enter failsafe mode
- regular preinit -
jffs2 not ready yet; using ramdisk
- init -

Please press Enter to activate this console. [    9.856000] Compat-drivers backport release: compat-drivers-2013-01-21-1
[    9.860000] Backport based on wireless-testing.git master-2013-02-22
[    9.864000] compat.git: wireless-testing.git
[    9.960000] cfg80211: Calling CRDA to update world regulatory domain
[   10.008000] cfg80211: World regulatory domain updated:
[   10.012000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[   10.020000] cfg80211:   (2402000 KHz - 2494000 KHz @ 40000 KHz), (500 mBi, 3000 mBm)
[   10.028000] cfg80211:   (4910000 KHz - 5835000 KHz @ 40000 KHz), (N/A, 3000 mBm)
[   10.768000] PCI: Enabling device 0000:00:0e.0 (0000 -> 0002)
[   12.348000] ieee80211 phy0: Atheros AR9280 Rev:2 mem=0xb8000000, irq=30
[   12.356000] cfg80211: Calling CRDA for country: US
[   12.360000] cfg80211: Regulatory domain changed to country: US
[   12.364000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[   12.372000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
[   12.380000] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)
[   12.388000] cfg80211:   (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   12.396000] cfg80211:   (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   12.404000] cfg80211:   (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   12.412000] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)
[   12.436000] NET: Registered protocol family 8
[   12.440000] NET: Registered protocol family 20
[   12.740000] PPP generic driver version 2.4.2
[   12.952000] ip_tables: (C) 2000-2006 Netfilter Core Team
[   13.104000] NET: Registered protocol family 24
[   13.128000] nf_conntrack version 0.5.0 (958 buckets, 3832 max)
[   13.384000] IFX MEI Version 5.00.00
[   13.404000] IFXUSB: ifxusb_hcd: version 3.2 B110801
[   13.908000] IFXUSB: USB core #0 soft-reset
[   14.112000] IFXUSB: USB core #0 soft-reset
[   14.112000] ifxusb_hcd ifxusb_hcd: IFX USB Controller
[   14.120000] ifxusb_hcd ifxusb_hcd: new USB bus registered, assigned bus number 1
[   14.124000] ifxusb_hcd ifxusb_hcd: irq 62, io mem 0xbe101000
[   14.132000] IFXUSB: Init: Power Port (0)
[   14.136000] hub 1-0:1.0: USB hub found
[   14.140000] hub 1-0:1.0: 1 port detected
[   14.144000] ifxusb_hcd ifxusb_hcd: requested GPIO 236
[   14.172000] Infineon CPE API Driver version: DSL CPE API V3.24.4.4
[   14.192000] ATM1.0.26    ATM (A1) firmware version 0.16
[   14.196000] ifxmips_atm: ATM init succeed
[   18.104000] XR9-x chip found
DDR set @ 166.6MHz
Check initial DDR setting...DDR check ok... start booting...



ARCADYAN U-Boot 1.00 (Nov 10 2010 - 17:41:42)

AR9 BOARD
CLOCK CPU 333M RAM 166M
DRAM:  64 MB

 relocate_code start
 relocate_code finish.
Flash: 32 MB
In:    serial
Out:   serial
Err:   serial
Net:   
switch chip id=00001001
AR8316
amazon_s Switch

Copying boot params.....
DONE

Type "run flash_nfs" to mount root filesystem over NFS

Hit any key to stop autoboot:  3  2  1  0 
## Booting image at b0060000 ...
   Image Name:   MIPS OpenWrt Linux-3.8.3
   Created:      2013-04-03  22:13:46 UTC
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    1201861 Bytes =  1.1 MB
   Load Address: 80002000
   Entry Point:  80002000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80002000) ...
## Giving linux memsize in MB, 64

Starting kernel ...

[    0.000000] Linux version 3.8.3 (daniele@danfedvm.localdomain) (gcc version 4.6.4 20121210 (prerelease) (Linaro GCC 4.6-2012.12) ) #4 Thu Apr 4 00:13:38 CEST 2013

[    0.000000] SoC: AR9 rev 1.2

[    0.000000] bootconsole [early0] enabled

[    0.000000] CPU revision is: 0001954c (MIPS 34Kc)

[    0.000000] Determined physical RAM map:

[    0.000000]  memory: 04000000 @ 00000000 (usable)

[    0.000000] Initrd not found or empty - disabling initrd

[    0.000000] Zone ranges:

[    0.000000]   Normal   [mem 0x00000000-0x03ffffff]

[    0.000000] Movable zone start for each node

[    0.000000] Early memory node ranges

[    0.000000]   node   0: [mem 0x00000000-0x03ffffff]

[    0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.

[    0.000000] Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 32 bytes

[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256

[    0.000000] Kernel command line: console=ttyLTQ0,115200 init=/etc/preinit

[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)

[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)

[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)

[    0.000000] __ex_table already sorted, skipping sort

[    0.000000] Writing ErrCtl register=00040020

[    0.000000] Readback ErrCtl register=00040020

[    0.000000] Memory: 61128k/65536k available (2563k kernel code, 4408k reserved, 783k data, 228k init, 0k highmem)

[    0.000000] NR_IRQS:256

[    0.000000] CPU Clock: 333MHz

[    0.000000] Calibrating delay loop... 221.18 BogoMIPS (lpj=442368)

[    0.040000] pid_max: default: 32768 minimum: 301

[    0.044000] Mount-cache hash table entries: 512

[    0.048000] pinctrl core: initialized pinctrl subsystem

[    0.052000] NET: Registered protocol family 16

[    0.068000] pinctrl-xway 1e100b10.pinmux: Init done

[    0.072000] dma-xway 1e104100.dma: Init done - hw rev: 6, ports: 5, channels: 20

[    0.080000] PCI host bridge /fpi@10000000/pci@E105400 ranges:

[    0.084000]  MEM 0x0000000018000000..0x0000000019ffffff

[    0.088000]   IO 0x000000001ae00000..0x000000001affffff

[    0.108000] bio: create slab <bio-0> at 0

[    0.116000] usbcore: registered new interface driver usbfs

[    0.120000] usbcore: registered new interface driver hub

[    0.124000] usbcore: registered new device driver usb

[    0.128000] PCI host bridge to bus 0000:00

[    0.132000] pci_bus 0000:00: root bus resource [mem 0x18000000-0x19ffffff]

[    0.136000] pci_bus 0000:00: root bus resource [io  0x1ae00000-0x1affffff]

[    0.140000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]

[    0.144000] pci 0000:00:0e.0: BAR 0: assigned [mem 0x18000000-0x1800ffff]

[    0.148000] pci 0000:00:0e.0: SLOT:14 PIN:1 IRQ:30

[    0.152000] Switching to clocksource MIPS

[    0.160000] NET: Registered protocol family 2

[    0.164000] TCP established hash table entries: 512 (order: 0, 4096 bytes)

[    0.172000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)

[    0.180000] TCP: Hash tables configured (established 512 bind 512)

[    0.184000] TCP: reno registered

[    0.188000] UDP hash table entries: 256 (order: 0, 4096 bytes)

[    0.196000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)

[    0.200000] NET: Registered protocol family 1

[    0.204000] gptu: totally 6 16-bit timers/counters

[    0.212000] gptu: misc_register on minor 63

[    0.216000] gptu: succeeded to request irq 126

[    0.220000] gptu: succeeded to request irq 127

[    0.224000] gptu: succeeded to request irq 128

[    0.228000] gptu: succeeded to request irq 129

[    0.232000] gptu: succeeded to request irq 130

[    0.236000] gptu: succeeded to request irq 131

[    0.248000] squashfs: version 4.0 (2009/01/31) Phillip Lougher

[    0.256000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.

[    0.264000] msgmni has been set to 119

[    0.268000] io scheduler noop registered

[    0.272000] io scheduler deadline registered (default)

[    0.280000] 1e100c00.serial: ttyLTQ0 at MMIO 0x1e100c00 (irq = 112) is a lantiq,asc

[    0.288000] console [ttyLTQ0] enabled, bootconsole disabled
[    0.288000] console [ttyLTQ0] enabled, bootconsole disabled

[    0.300000] ltq_nor: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x00227e
[    0.308000] Amd/Fujitsu Extended Query Table at 0x0040
[    0.316000]   Amd/Fujitsu Extended Query version 1.3.
[    0.320000] number of CFI chips: 1
[    0.324000] 5 ofpart partitions found on MTD device ltq_nor
[    0.328000] Creating 5 MTD partitions on "ltq_nor":
[    0.332000] 0x000000000000-0x000000040000 : "uboot"
[    0.340000] 0x000000040000-0x000000060000 : "uboot_env"
[    0.348000] 0x000000060000-0x000001f80000 : "linux"
[    0.352000] found squashfs behind kernel
[    0.356000] Creating 2 MTD partitions on "ltq_nor":
[    0.360000] 0x000000060000-0x000000185705 : "kernel"
[    0.364000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    0.380000] 0x000000185705-0x000001f80000 : "rootfs"
[    0.384000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    0.400000] mtd: partition "rootfs" set to be root filesystem
[    0.404000] mtd: partition "rootfs_data" created automatically, ofs=3E0000, len=1BA0000 
[    0.412000] 0x0000003e0000-0x000001f80000 : "rootfs_data"
[    0.420000] 0x000001fc0000-0x000001fe0000 : "board"
[    0.428000] 0x000001fe0000-0x000002000000 : "calibration"
[    0.468000] switch0: Atheros AR8316 switch registered on 1e180000.etop-ff
[    0.496000] libphy: ltq_mii: probed
[    0.500000] ar8316: Using port 4 as switch port
[    1.608000] eth0: attached PHY [Atheros AR8216/AR8236/AR8316] (phy_addr=1e180000.etop-ff:00, irq=-1)
[    1.616000] wdt 1f8803f0.watchdog: Init done
[    1.624000] leds-gpio gpio-leds.5: pins are not configured from the driver
[    1.636000] TCP: cubic registered
[    1.636000] NET: Registered protocol family 17
[    1.640000] 8021q: 802.1Q VLAN Support v1.8
[    1.652000] VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
[    1.660000] Freeing unused kernel memory: 228k freed
- preinit -
Press the [f] key and hit [enter] to enter failsafe mode
- regular preinit -
jffs2 not ready yet; using ramdisk
- init -

Please press Enter to activate this console. [    9.852000] Compat-drivers backport release: compat-drivers-2013-01-21-1
[    9.856000] Backport based on wireless-testing.git master-2013-02-22
[    9.864000] compat.git: wireless-testing.git
[    9.900000] cfg80211: Calling CRDA to update world regulatory domain
[    9.904000] cfg80211: World regulatory domain updated:
[    9.908000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[    9.916000] cfg80211:   (2402000 KHz - 2494000 KHz @ 40000 KHz), (500 mBi, 3000 mBm)
[    9.924000] cfg80211:   (4910000 KHz - 5835000 KHz @ 40000 KHz), (N/A, 3000 mBm)
[   10.772000] PCI: Enabling device 0000:00:0e.0 (0000 -> 0002)
[   12.352000] ieee80211 phy0: Atheros AR9280 Rev:2 mem=0xb8000000, irq=30
[   12.384000] NET: Registered protocol family 8
[   12.388000] NET: Registered protocol family 20
[   12.424000] cfg80211: Calling CRDA for country: US
[   12.580000] cfg80211: Regulatory domain changed to country: US
[   12.584000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[   12.592000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
[   12.600000] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)
[   12.608000] cfg80211:   (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   12.612000] cfg80211:   (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   12.620000] cfg80211:   (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   12.628000] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)
[   13.032000] PPP generic driver version 2.4.2
[   14.064000] ip_tables: (C) 2000-2006 Netfilter Core Team
[   14.876000] NET: Registered protocol family 24
[   15.020000] nf_conntrack version 0.5.0 (958 buckets, 3832 max)
[   17.652000] XR9-x chip found
DDR set @ 166.6MHz
Check initial DDR setting...DDR check ok... start booting...



ARCADYAN U-Boot 1.00 (Nov 10 2010 - 17:41:42)

AR9 BOARD
CLOCK CPU 333M RAM 166M
DRAM:  64 MB

 relocate_code start
 relocate_code finish.
Flash: 32 MB
In:    serial
Out:   serial
Err:   serial
Net:   
switch chip id=00001001
AR8316
amazon_s Switch

Copying boot params.....
DONE

Type "run flash_nfs" to mount root filesystem over NFS

Hit any key to stop autoboot:  3  2  1  0 
## Booting image at b0060000 ...
   Image Name:   MIPS OpenWrt Linux-3.8.3
   Created:      2013-04-03  22:13:46 UTC
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    1201861 Bytes =  1.1 MB
   Load Address: 80002000
   Entry Point:  80002000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80002000) ...
## Giving linux memsize in MB, 64

Starting kernel ...

[    0.000000] Linux version 3.8.3 (daniele@danfedvm.localdomain) (gcc version 4.6.4 20121210 (prerelease) (Linaro GCC 4.6-2012.12) ) #4 Thu Apr 4 00:13:38 CEST 2013

[    0.000000] SoC: AR9 rev 1.2

[    0.000000] bootconsole [early0] enabled

[    0.000000] CPU revision is: 0001954c (MIPS 34Kc)

[    0.000000] Determined physical RAM map:

[    0.000000]  memory: 04000000 @ 00000000 (usable)

[    0.000000] Initrd not found or empty - disabling initrd

[    0.000000] Zone ranges:

[    0.000000]   Normal   [mem 0x00000000-0x03ffffff]

[    0.000000] Movable zone start for each node

[    0.000000] Early memory node ranges

[    0.000000]   node   0: [mem 0x00000000-0x03ffffff]

[    0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.

[    0.000000] Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 32 bytes

[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256

[    0.000000] Kernel command line: console=ttyLTQ0,115200 init=/etc/preinit

[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)

[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)

[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)

[    0.000000] __ex_table already sorted, skipping sort

[    0.000000] Writing ErrCtl register=00040020

[    0.000000] Readback ErrCtl register=00040020

[    0.000000] Memory: 61128k/65536k available (2563k kernel code, 4408k reserved, 783k data, 228k init, 0k highmem)

[    0.000000] NR_IRQS:256

[    0.000000] CPU Clock: 333MHz

[    0.000000] Calibrating delay loop... 221.18 BogoMIPS (lpj=442368)

[    0.040000] pid_max: default: 32768 minimum: 301

[    0.044000] Mount-cache hash table entries: 512

[    0.048000] pinctrl core: initialized pinctrl subsystem

[    0.052000] NET: Registered protocol family 16

[    0.068000] pinctrl-xway 1e100b10.pinmux: Init done

[    0.072000] dma-xway 1e104100.dma: Init done - hw rev: 6, ports: 5, channels: 20

[    0.080000] PCI host bridge /fpi@10000000/pci@E105400 ranges:

[    0.084000]  MEM 0x0000000018000000..0x0000000019ffffff

[    0.088000]   IO 0x000000001ae00000..0x000000001affffff

[    0.108000] bio: create slab <bio-0> at 0

[    0.116000] usbcore: registered new interface driver usbfs

[    0.120000] usbcore: registered new interface driver hub

[    0.124000] usbcore: registered new device driver usb

[    0.128000] PCI host bridge to bus 0000:00

[    0.132000] pci_bus 0000:00: root bus resource [mem 0x18000000-0x19ffffff]

[    0.136000] pci_bus 0000:00: root bus resource [io  0x1ae00000-0x1affffff]

[    0.140000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]

[    0.144000] pci 0000:00:0e.0: BAR 0: assigned [mem 0x18000000-0x1800ffff]

[    0.148000] pci 0000:00:0e.0: SLOT:14 PIN:1 IRQ:30

[    0.152000] Switching to clocksource MIPS

[    0.160000] NET: Registered protocol family 2

[    0.164000] TCP established hash table entries: 512 (order: 0, 4096 bytes)

[    0.172000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)

[    0.180000] TCP: Hash tables configured (established 512 bind 512)

[    0.184000] TCP: reno registered

[    0.188000] UDP hash table entries: 256 (order: 0, 4096 bytes)

[    0.196000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)

[    0.200000] NET: Registered protocol family 1

[    0.204000] gptu: totally 6 16-bit timers/counters

[    0.212000] gptu: misc_register on minor 63

[    0.216000] gptu: succeeded to request irq 126

[    0.220000] gptu: succeeded to request irq 127

[    0.224000] gptu: succeeded to request irq 128

[    0.228000] gptu: succeeded to request irq 129

[    0.232000] gptu: succeeded to request irq 130

[    0.236000] gptu: succeeded to request irq 131

[    0.248000] squashfs: version 4.0 (2009/01/31) Phillip Lougher

[    0.256000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.

[    0.264000] msgmni has been set to 119

[    0.268000] io scheduler noop registered

[    0.272000] io scheduler deadline registered (default)

[    0.280000] 1e100c00.serial: ttyLTQ0 at MMIO 0x1e100c00 (irq = 112) is a lantiq,asc

[    0.288000] console [ttyLTQ0] enabled, bootconsole disabled
[    0.288000] console [ttyLTQ0] enabled, bootconsole disabled

[    0.300000] ltq_nor: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x00227e
[    0.308000] Amd/Fujitsu Extended Query Table at 0x0040
[    0.316000]   Amd/Fujitsu Extended Query version 1.3.
[    0.320000] number of CFI chips: 1
[    0.324000] 5 ofpart partitions found on MTD device ltq_nor
[    0.328000] Creating 5 MTD partitions on "ltq_nor":
[    0.332000] 0x000000000000-0x000000040000 : "uboot"
[    0.340000] 0x000000040000-0x000000060000 : "uboot_env"
[    0.348000] 0x000000060000-0x000001f80000 : "linux"
[    0.352000] found squashfs behind kernel
[    0.356000] Creating 2 MTD partitions on "ltq_nor":
[    0.360000] 0x000000060000-0x000000185705 : "kernel"
[    0.364000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    0.380000] 0x000000185705-0x000001f80000 : "rootfs"
[    0.384000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    0.400000] mtd: partition "rootfs" set to be root filesystem
[    0.404000] mtd: partition "rootfs_data" created automatically, ofs=3E0000, len=1BA0000 
[    0.412000] 0x0000003e0000-0x000001f80000 : "rootfs_data"
[    0.420000] 0x000001fc0000-0x000001fe0000 : "board"
[    0.428000] 0x000001fe0000-0x000002000000 : "calibration"
[    0.468000] switch0: Atheros AR8316 switch registered on 1e180000.etop-ff
[    0.496000] libphy: ltq_mii: probed
[    0.500000] ar8316: Using port 4 as switch port
[    1.608000] eth0: attached PHY [Atheros AR8216/AR8236/AR8316] (phy_addr=1e180000.etop-ff:00, irq=-1)
[    1.616000] wdt 1f8803f0.watchdog: Init done
[    1.624000] leds-gpio gpio-leds.5: pins are not configured from the driver
[    1.636000] TCP: cubic registered
[    1.636000] NET: Registered protocol family 17
[    1.640000] 8021q: 802.1Q VLAN Support v1.8
[    1.652000] VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
[    1.660000] Freeing unused kernel memory: 228k freed
- preinit -
Press the [f] key and hit [enter] to enter failsafe mode
- regular preinit -
jffs2 not ready yet; using ramdisk
- init -

Please press Enter to activate this console. [    9.864000] Compat-drivers backport release: compat-drivers-2013-01-21-1
[    9.868000] Backport based on wireless-testing.git master-2013-02-22
[    9.876000] compat.git: wireless-testing.git
[    9.912000] cfg80211: Calling CRDA to update world regulatory domain
[    9.916000] cfg80211: World regulatory domain updated:
[    9.920000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[    9.928000] cfg80211:   (2402000 KHz - 2494000 KHz @ 40000 KHz), (500 mBi, 3000 mBm)
[    9.936000] cfg80211:   (4910000 KHz - 5835000 KHz @ 40000 KHz), (N/A, 3000 mBm)
[   10.780000] PCI: Enabling device 0000:00:0e.0 (0000 -> 0002)
[   12.360000] ieee80211 phy0: Atheros AR9280 Rev:2 mem=0xb8000000, irq=30
[   12.388000] NET: Registered protocol family 8
[   12.392000] NET: Registered protocol family 20
[   12.396000] cfg80211: Calling CRDA for country: US
[   12.400000] cfg80211: Regulatory domain changed to country: US
[   12.404000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[   12.412000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
[   12.420000] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)
[   12.428000] cfg80211:   (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   12.436000] cfg80211:   (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   12.444000] cfg80211:   (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   12.452000] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)
[   12.756000] PPP generic driver version 2.4.2
[   12.968000] ip_tables: (C) 2000-2006 Netfilter Core Team
[   13.120000] NET: Registered protocol family 24
[   13.144000] nf_conntrack version 0.5.0 (958 buckets, 3832 max)
[   13.400000] IFX MEI Version 5.00.00
[   13.420000] IFXUSB: ifxusb_hcd: version 3.2 B110801
[   13.924000] IFXUSB: USB core #0 soft-reset
[   14.128000] IFXUSB: USB core #0 soft-reset
[   14.128000] ifxusb_hcd ifxusb_hcd: IFX USB Controller
[   14.136000] ifxusb_hcd ifxusb_hcd: new USB bus registered, assigned bus number 1
[   14.140000] ifxusb_hcd ifxusb_hcd: irq 62, io mem 0xbe101000
[   14.148000] IFXUSB: Init: Power Port (0)
[   14.152000] hub 1-0:1.0: USB hub found
[   14.156000] hub 1-0:1.0: 1 port detected
[   14.160000] ifxusb_hcd ifxusb_hcd: requested GPIO 236
[   14.188000] Infineon CPE API Driver version: DSL CPE API V3.24.4.4
[   14.212000] ATM1.0.26    ATM (A1) firmware version 0.16
[   14.216000] ifxmips_atm: ATM init succeed
[   18.336000]þXR9-x chip found
DDR set @ 166.6MHz
Check initial DDR setting...DDR check ok... start booting...



ARCADYAN U-Boot 1.00 (Nov 10 2010 - 17:41:42)

AR9 BOARD
CLOCK CPU 333M RAM 166M
DRAM:  64 MB

 relocate_code start
 relocate_code finish.
Flash: 32 MB
In:    serial
Out:   serial
Err:   serial
Net:   
switch chip id=00001001
AR8316
amazon_s Switch

Copying boot params.....
DONE

Type "run flash_nfs" to mount root filesystem over NFS

Hit any key to stop autoboot:  3  2  1  0 
## Booting image at b0060000 ...
   Image Name:   MIPS OpenWrt Linux-3.8.3
   Created:      2013-04-03  22:13:46 UTC
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    1201861 Bytes =  1.1 MB
   Load Address: 80002000
   Entry Point:  80002000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80002000) ...
## Giving linux memsize in MB, 64

Starting kernel ...

[    0.000000] Linux version 3.8.3 (daniele@danfedvm.localdomain) (gcc version 4.6.4 20121210 (prerelease) (Linaro GCC 4.6-2012.12) ) #4 Thu Apr 4 00:13:38 CEST 2013

[    0.000000] SoC: AR9 rev 1.2

[    0.000000] bootconsole [early0] enabled

[    0.000000] CPU revision is: 0001954c (MIPS 34Kc)

[    0.000000] Determined physical RAM map:

[    0.000000]  memory: 04000000 @ 00000000 (usable)

[    0.000000] Initrd not found or empty - disabling initrd

[    0.000000] Zone ranges:

[    0.000000]   Normal   [mem 0x00000000-0x03ffffff]

[    0.000000] Movable zone start for each node

[    0.000000] Early memory node ranges

[    0.000000]   node   0: [mem 0x00000000-0x03ffffff]

[    0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.

[    0.000000] Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 32 bytes

[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256

[    0.000000] Kernel command line: console=ttyLTQ0,115200 init=/etc/preinit

[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)

[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)

[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)

[    0.000000] __ex_table already sorted, skipping sort

[    0.000000] Writing ErrCtl register=00040020

[    0.000000] Readback ErrCtl register=00040020

[    0.000000] Memory: 61128k/65536k available (2563k kernel code, 4408k reserved, 783k data, 228k init, 0k highmem)

[    0.000000] NR_IRQS:256

[    0.000000] CPU Clock: 333MHz

[    0.000000] Calibrating delay loop... 221.18 BogoMIPS (lpj=442368)

[    0.040000] pid_max: default: 32768 minimum: 301

[    0.044000] Mount-cache hash table entries: 512

[    0.048000] pinctrl core: initialized pinctrl subsystem

[    0.052000] NET: Registered protocol family 16

[    0.068000] pinctrl-xway 1e100b10.pinmux: Init done

[    0.072000] dma-xway 1e104100.dma: Init done - hw rev: 6, ports: 5, channels: 20

[    0.080000] PCI host bridge /fpi@10000000/pci@E105400 ranges:

[    0.084000]  MEM 0x0000000018000000..0x0000000019ffffff

[    0.088000]   IO 0x000000001ae00000..0x000000001affffff

[    0.108000] bio: create slab <bio-0> at 0

[    0.116000] usbcore: registered new interface driver usbfs

[    0.120000] usbcore: registered new interface driver hub

[    0.124000] usbcore: registered new device driver usb

[    0.128000] PCI host bridge to bus 0000:00

[    0.132000] pci_bus 0000:00: root bus resource [mem 0x18000000-0x19ffffff]

[    0.136000] pci_bus 0000:00: root bus resource [io  0x1ae00000-0x1affffff]

[    0.140000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]

[    0.144000] pci 0000:00:0e.0: BAR 0: assigned [mem 0x18000000-0x1800ffff]

[    0.148000] pci 0000:00:0e.0: SLOT:14 PIN:1 IRQ:30

[    0.152000] Switching to clocksource MIPS

[    0.160000] NET: Registered protocol family 2

[    0.164000] TCP established hash table entries: 512 (order: 0, 4096 bytes)

[    0.172000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)

[    0.180000] TCP: Hash tables configured (established 512 bind 512)

[    0.184000] TCP: reno registered

[    0.188000] UDP hash table entries: 256 (order: 0, 4096 bytes)

[    0.196000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)

[    0.200000] NET: Registered protocol family 1

[    0.204000] gptu: totally 6 16-bit timers/counters

[    0.212000] gptu: misc_register on minor 63

[    0.216000] gptu: succeeded to request irq 126

[    0.220000] gptu: succeeded to request irq 127

[    0.224000] gptu: succeeded to request irq 128

[    0.228000] gptu: succeeded to request irq 129

[    0.232000] gptu: succeeded to request irq 130

[    0.236000] gptu: succeeded to request irq 131

[    0.248000] squashfs: version 4.0 (2009/01/31) Phillip Lougher

[    0.256000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.

[    0.264000] msgmni has been set to 119

[    0.268000] io scheduler noop registered

[    0.272000] io scheduler deadline registered (default)

[    0.280000] 1e100c00.serial: ttyLTQ0 at MMIO 0x1e100c00 (irq = 112) is a lantiq,asc

[    0.288000] console [ttyLTQ0] enabled, bootconsole disabled
[    0.288000] console [ttyLTQ0] enabled, bootconsole disabled

[    0.300000] ltq_nor: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x00227e
[    0.308000] Amd/Fujitsu Extended Query Table at 0x0040
[    0.316000]   Amd/Fujitsu Extended Query version 1.3.
[    0.320000] number of CFI chips: 1
[    0.324000] 5 ofpart partitions found on MTD device ltq_nor
[    0.328000] Creating 5 MTD partitions on "ltq_nor":
[    0.332000] 0x000000000000-0x000000040000 : "uboot"
[    0.340000] 0x000000040000-0x000000060000 : "uboot_env"
[    0.348000] 0x000000060000-0x000001f80000 : "linux"
[    0.352000] found squashfs behind kernel
[    0.356000] Creating 2 MTD partitions on "ltq_nor":
[    0.360000] 0x000000060000-0x000000185705 : "kernel"
[    0.364000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    0.380000] 0x000000185705-0x000001f80000 : "rootfs"
[    0.384000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    0.400000] mtd: partition "rootfs" set to be root filesystem
[    0.404000] mtd: partition "rootfs_data" created automatically, ofs=3E0000, len=1BA0000 
[    0.412000] 0x0000003e0000-0x000001f80000 : "rootfs_data"
[    0.420000] 0x000001fc0000-0x000001fe0000 : "board"
[    0.428000] 0x000001fe0000-0x000002000000 : "calibration"
[    0.468000] switch0: Atheros AR8316 switch registered on 1e180000.etop-ff
[    0.496000] libphy: ltq_mii: probed
[    0.500000] ar8316: Using port 4 as switch port
[    1.608000] eth0: attached PHY [Atheros AR8216/AR8236/AR8316] (phy_addr=1e180000.etop-ff:00, irq=-1)
[    1.616000] wdt 1f8803f0.watchdog: Init done
[    1.624000] leds-gpio gpio-leds.5: pins are not configured from the driver
[    1.636000] TCP: cubic registered
[    1.636000] NET: Registered protocol family 17
[    1.640000] 8021q: 802.1Q VLAN Support v1.8
[    1.652000] VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
[    1.660000] Freeing unused kernel memory: 228k freed
- preinit -
Press the [f] key and hit [enter] to enter failsafe mode
....
....
....

Tell me if you need additional informations. An "old" attitude adjustment build I use to restore from this endless reboot state is working well(so it is not an hardware problem)

Thanks
Daniele Buffa.

comment:5 Changed 5 years ago by anonymous

it seems to me that your reboot button is being triggered.

try building an image without the button driver to verify if this is indeed the case

comment:6 Changed 5 years ago by d.buffa@…

can you tell me how can i do it? thank you

D.

comment:7 Changed 5 years ago by d.buffa@…

How can I disable the button driver, in order to make the test?

Thanks
D.

comment:8 Changed 5 years ago by d.buffa@…

Tried with last r36354, the issue is still present

Upgrade completed
Rebooting system...
[  614.944000] Restarting system.
[  614.944000]àXR9-x chip found
DDR set @ 166.6MHz
Check initial DDR setting...DDR check ok... start booting...



ARCADYAN U-Boot 1.00 (Nov 10 2010 - 17:41:42)

AR9 BOARD
CLOCK CPU 333M RAM 166M
DRAM:  64 MB

 relocate_code start
 relocate_code finish.
Flash: 32 MB
In:    serial
Out:   serial
Err:   serial
Net:   
switch chip id=00001001
AR8316
amazon_s Switch

Copying boot params.....
DONE

Type "run flash_nfs" to mount root filesystem over NFS

Hit any key to stop autoboot:  3  2  1  0 
## Booting image at b0060000 ...
   Image Name:   MIPS OpenWrt Linux-3.8.7
   Created:      2013-04-17  22:45:25 UTC
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    1221020 Bytes =  1.2 MB
   Load Address: 80002000
   Entry Point:  80002000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80002000) ...
## Giving linux memsize in MB, 64

Starting kernel ...

[    0.000000] Linux version 3.8.7 (daniele@danfedvm.localdomain) (gcc version 4.6.4 (OpenWrt/Linaro GCC 4.6-2012.12 r36237) ) #1 Thu Apr 18 00:45:16 CEST 2013

[    0.000000] SoC: AR9 rev 1.2

[    0.000000] bootconsole [early0] enabled

[    0.000000] CPU revision is: 0001954c (MIPS 34Kc)

[    0.000000] MIPS: machine is WBMR - Buffalo WBMR-HP-G300H

[    0.000000] Determined physical RAM map:

[    0.000000]  memory: 04000000 @ 00000000 (usable)

[    0.000000] Initrd not found or empty - disabling initrd

[    0.000000] Zone ranges:

[    0.000000]   Normal   [mem 0x00000000-0x03ffffff]

[    0.000000] Movable zone start for each node

[    0.000000] Early memory node ranges

[    0.000000]   node   0: [mem 0x00000000-0x03ffffff]

[    0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.

[    0.000000] Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 32 bytes

[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256

[    0.000000] Kernel command line: console=ttyLTQ0,115200 init=/etc/preinit

[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)

[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)

[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)

[    0.000000] __ex_table already sorted, skipping sort

[    0.000000] Writing ErrCtl register=00001020

[    0.000000] Readback ErrCtl register=00001020

[    0.000000] Memory: 61064k/65536k available (2588k kernel code, 4472k reserved, 853k data, 196k init, 0k highmem)

[    0.000000] NR_IRQS:256

[    0.000000] CPU Clock: 333MHz

[    0.000000] Calibrating delay loop... 221.18 BogoMIPS (lpj=442368)

[    0.040000] pid_max: default: 32768 minimum: 301

[    0.044000] Mount-cache hash table entries: 512

[    0.048000] pinctrl core: initialized pinctrl subsystem

[    0.052000] NET: Registered protocol family 16

[    0.068000] pinctrl-xway 1e100b10.pinmux: Init done

[    0.072000] dma-xway 1e104100.dma: Init done - hw rev: 6, ports: 5, channels: 20

[    0.080000] PCI host bridge /fpi@10000000/pci@E105400 ranges:

[    0.084000]  MEM 0x0000000018000000..0x0000000019ffffff

[    0.088000]   IO 0x000000001ae00000..0x000000001affffff

[    0.108000] bio: create slab <bio-0> at 0

[    0.116000] usbcore: registered new interface driver usbfs

[    0.120000] usbcore: registered new interface driver hub

[    0.124000] usbcore: registered new device driver usb

[    0.128000] PCI host bridge to bus 0000:00

[    0.132000] pci_bus 0000:00: root bus resource [mem 0x18000000-0x19ffffff]

[    0.136000] pci_bus 0000:00: root bus resource [io  0x1ae00000-0x1affffff]

[    0.140000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]

[    0.144000] pci 0000:00:0e.0: BAR 0: assigned [mem 0x18000000-0x1800ffff]

[    0.148000] pci 0000:00:0e.0: SLOT:14 PIN:1 IRQ:30

[    0.152000] Switching to clocksource MIPS

[    0.160000] NET: Registered protocol family 2

[    0.164000] TCP established hash table entries: 512 (order: 0, 4096 bytes)

[    0.172000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)

[    0.180000] TCP: Hash tables configured (established 512 bind 512)

[    0.184000] TCP: reno registered

[    0.188000] UDP hash table entries: 256 (order: 0, 4096 bytes)

[    0.196000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)

[    0.200000] NET: Registered protocol family 1

[    0.204000] gptu: totally 6 16-bit timers/counters

[    0.212000] gptu: misc_register on minor 63

[    0.216000] gptu: succeeded to request irq 126

[    0.220000] gptu: succeeded to request irq 127

[    0.224000] gptu: succeeded to request irq 128

[    0.228000] gptu: succeeded to request irq 129

[    0.232000] gptu: succeeded to request irq 130

[    0.236000] gptu: succeeded to request irq 131

[    0.248000] squashfs: version 4.0 (2009/01/31) Phillip Lougher

[    0.256000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.

[    0.264000] msgmni has been set to 119

[    0.268000] io scheduler noop registered

[    0.272000] io scheduler deadline registered (default)

[    0.280000] 1e100c00.serial: ttyLTQ0 at MMIO 0x1e100c00 (irq = 112) is a lantiq,asc

[    0.288000] console [ttyLTQ0] enabled, bootconsole disabled
[    0.288000] console [ttyLTQ0] enabled, bootconsole disabled

[    0.300000] ltq_nor: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x00227e
[    0.308000] Amd/Fujitsu Extended Query Table at 0x0040
[    0.316000]   Amd/Fujitsu Extended Query version 1.3.
[    0.320000] number of CFI chips: 1
[    0.324000] 5 ofpart partitions found on MTD device ltq_nor
[    0.328000] Creating 5 MTD partitions on "ltq_nor":
[    0.332000] 0x000000000000-0x000000040000 : "uboot"
[    0.340000] 0x000000040000-0x000000060000 : "uboot_env"
[    0.348000] 0x000000060000-0x000001f80000 : "linux"
[    0.352000] found squashfs behind kernel
[    0.356000] Creating 2 MTD partitions on "ltq_nor":
[    0.360000] 0x000000060000-0x00000018a1dc : "kernel"
[    0.364000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    0.380000] 0x00000018a1dc-0x000001f80000 : "rootfs"
[    0.384000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    0.400000] mtd: partition "rootfs" set to be root filesystem
[    0.404000] mtd: partition "rootfs_data" created automatically, ofs=5C0000, len=19C0000 
[    0.412000] 0x0000005c0000-0x000001f80000 : "rootfs_data"
[    0.420000] 0x000001fc0000-0x000001fe0000 : "board"
[    0.424000] 0x000001fe0000-0x000002000000 : "calibration"
[    0.468000] switch0: Atheros AR8316 switch registered on 1e180000.etop-ff
[    0.496000] libphy: ltq_mii: probed
[    0.500000] ar8316: Using port 4 as switch port
[    1.608000] eth0: attached PHY [Atheros AR8216/AR8236/AR8316] (phy_addr=1e180000.etop-ff:00, irq=-1)
[    1.616000] wdt 1f8803f0.watchdog: Init done
[    1.624000] leds-gpio gpio-leds.5: pins are not configured from the driver
[    1.636000] TCP: cubic registered
[    1.636000] NET: Registered protocol family 17
[    1.640000] 8021q: 802.1Q VLAN Support v1.8
[    1.652000] VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
[    1.660000] Freeing unused kernel memory: 196k freed
- preinit -
Press the [f] key and hit [enter] to enter failsafe mode
- regular preinit -
jffs2 not ready yet; using ramdisk
- init -

Please press Enter to activate this console. [   10.436000] Compat-drivers backport release: compat-drivers-2013-01-21-1
[   10.440000] Backport based on wireless-testing.git master-2013-02-22
[   10.448000] compat.git: wireless-testing.git
[   10.648000] cfg80211: Calling CRDA to update world regulatory domain
[   10.652000] cfg80211: World regulatory domain updated:
[   10.656000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[   10.664000] cfg80211:   (2402000 KHz - 2494000 KHz @ 40000 KHz), (500 mBi, 3000 mBm)
[   10.672000] cfg80211:   (4910000 KHz - 5835000 KHz @ 40000 KHz), (N/A, 3000 mBm)
[   11.860000] PCI: Enabling device 0000:00:0e.0 (0000 -> 0002)
[   13.436000] ieee80211 phy0: Atheros AR9280 Rev:2 mem=0xb8000000, irq=30
[   13.448000] cfg80211: Calling CRDA for country: US
[   13.448000] cfg80211: Regulatory domain changed to country: US
[   13.456000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[   13.464000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
[   13.472000] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)
[   13.480000] cfg80211:   (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   13.488000] cfg80211:   (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   13.496000] cfg80211:   (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   13.500000] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)
[   13.532000] NET: Registered protocol family 8
[   13.536000] NET: Registered protocol family 20
[   14.420000] PPP generic driver version 2.4.2
[   14.556000] tun: Universal TUN/TAP device driver, 1.6
[   14.560000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[   14.760000] ip_tables: (C) 2000-2006 Netfilter Core Team
[   14.952000] NET: Registered protocol family 24
[   15.108000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[   15.132000] ehci-platform: EHCI generic platform driver
[   15.292000] nf_conntrack version 0.5.0 (957 buckets, 3828 max)
[   16.516000] xt_time: kernel timezone is -0000
[   18.008000] IFX MEI Version 5.00.00
[   18.160000] IFXUSB: ifxusb_hcd: version 3.2 B110801
[   18.664000] IFXUSB: USB core #0 soft-reset
[   18.864000] IFXUSB: USB core #0 soft-reset
[   18.868000] ifxusb_hcd ifxusb_hcd: IFX USB Controller
[   18.872000] ifxusb_hcd ifxusb_hcd: new USB bus registered, assigned bus number 1
[   18.880000] ifxusb_hcd ifxusb_hcd: irq 62, io mem 0xbe101000
[   18.884000] IFXUSB: Init: Power Port (0)
[   18.892000] hub 1-0:1.0: USB hub found
[   18.892000] hub 1-0:1.0: 1 port detected
[   18.896000] ifxusb_hcd ifxusb_hcd: requested GPIO 236
[   19.204000] Infineon CPE API Driver version: DSL CPE API V3.24.4.4
[   19.232000] ATM1.0.26    ATM (A1) firmware version 0.16
[   19.236000] ifxmips_atm: ATM init succeed
Didn't write all of the data.
[   21.840000]þXR9-x chip found
DDR set @ 166.6MHz
Check initial DDR setting...DDR check ok... start booting...



ARCADYAN U-Boot 1.00 (Nov 10 2010 - 17:41:42)

AR9 BOARD
CLOCK CPU 333M RAM 166M
DRAM:  64 MB

 relocate_code start
 relocate_code finish.
Flash: 32 MB
In:    serial
Out:   serial
Err:   serial
Net:   
switch chip id=00001001
AR8316
amazon_s Switch

Copying boot params.....
DONE

Type "run flash_nfs" to mount root filesystem over NFS

Hit any key to stop autoboot:  3  2  1  0 
## Booting image at b0060000 ...
   Image Name:   MIPS OpenWrt Linux-3.8.7
   Created:      2013-04-17  22:45:25 UTC
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    1221020 Bytes =  1.2 MB
   Load Address: 80002000
   Entry Point:  80002000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80002000) ...
## Giving linux memsize in MB, 64

Starting kernel ...

[    0.000000] Linux version 3.8.7 (daniele@danfedvm.localdomain) (gcc version 4.6.4 (OpenWrt/Linaro GCC 4.6-2012.12 r36237) ) #1 Thu Apr 18 00:45:16 CEST 2013

[    0.000000] SoC: AR9 rev 1.2

[    0.000000] bootconsole [early0] enabled

[    0.000000] CPU revision is: 0001954c (MIPS 34Kc)

[    0.000000] MIPS: machine is WBMR - Buffalo WBMR-HP-G300H

[    0.000000] Determined physical RAM map:

[    0.000000]  memory: 04000000 @ 00000000 (usable)

[    0.000000] Initrd not found or empty - disabling initrd

[    0.000000] Zone ranges:

[    0.000000]   Normal   [mem 0x00000000-0x03ffffff]

[    0.000000] Movable zone start for each node

[    0.000000] Early memory node ranges

[    0.000000]   node   0: [mem 0x00000000-0x03ffffff]

[    0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.

[    0.000000] Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 32 bytes

[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256

[    0.000000] Kernel command line: console=ttyLTQ0,115200 init=/etc/preinit

[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)

[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)

[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)

[    0.000000] __ex_table already sorted, skipping sort

[    0.000000] Writing ErrCtl register=00001028

[    0.000000] Readback ErrCtl register=00001028

[    0.000000] Memory: 61064k/65536k available (2588k kernel code, 4472k reserved, 853k data, 196k init, 0k highmem)

[    0.000000] NR_IRQS:256

[    0.000000] CPU Clock: 333MHz

[    0.000000] Calibrating delay loop... 221.18 BogoMIPS (lpj=442368)

[    0.040000] pid_max: default: 32768 minimum: 301

[    0.044000] Mount-cache hash table entries: 512

[    0.048000] pinctrl core: initialized pinctrl subsystem

[    0.052000] NET: Registered protocol family 16

[    0.068000] pinctrl-xway 1e100b10.pinmux: Init done

[    0.072000] dma-xway 1e104100.dma: Init done - hw rev: 6, ports: 5, channels: 20

[    0.080000] PCI host bridge /fpi@10000000/pci@E105400 ranges:

[    0.084000]  MEM 0x0000000018000000..0x0000000019ffffff

[    0.088000]   IO 0x000000001ae00000..0x000000001affffff

[    0.108000] bio: create slab <bio-0> at 0

[    0.116000] usbcore: registered new interface driver usbfs

[    0.120000] usbcore: registered new interface driver hub

[    0.124000] usbcore: registered new device driver usb

[    0.128000] PCI host bridge to bus 0000:00

[    0.132000] pci_bus 0000:00: root bus resource [mem 0x18000000-0x19ffffff]

[    0.136000] pci_bus 0000:00: root bus resource [io  0x1ae00000-0x1affffff]

[    0.140000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]

[    0.144000] pci 0000:00:0e.0: BAR 0: assigned [mem 0x18000000-0x1800ffff]

[    0.148000] pci 0000:00:0e.0: SLOT:14 PIN:1 IRQ:30

[    0.152000] Switching to clocksource MIPS

[    0.160000] NET: Registered protocol family 2

[    0.164000] TCP established hash table entries: 512 (order: 0, 4096 bytes)

[    0.172000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)

[    0.180000] TCP: Hash tables configured (established 512 bind 512)

[    0.184000] TCP: reno registered

[    0.188000] UDP hash table entries: 256 (order: 0, 4096 bytes)

[    0.196000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)

[    0.200000] NET: Registered protocol family 1

[    0.204000] gptu: totally 6 16-bit timers/counters

[    0.212000] gptu: misc_register on minor 63

[    0.216000] gptu: succeeded to request irq 126

[    0.220000] gptu: succeeded to request irq 127

[    0.224000] gptu: succeeded to request irq 128

[    0.228000] gptu: succeeded to request irq 129

[    0.232000] gptu: succeeded to request irq 130

[    0.236000] gptu: succeeded to request irq 131

[    0.248000] squashfs: version 4.0 (2009/01/31) Phillip Lougher

[    0.256000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.

[    0.264000] msgmni has been set to 119

[    0.268000] io scheduler noop registered

[    0.272000] io scheduler deadline registered (default)

[    0.280000] 1e100c00.serial: ttyLTQ0 at MMIO 0x1e100c00 (irq = 112) is a lantiq,asc

[    0.288000] console [ttyLTQ0] enabled, bootconsole disabled
[    0.288000] console [ttyLTQ0] enabled, bootconsole disabled

[    0.300000] ltq_nor: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x00227e
[    0.308000] Amd/Fujitsu Extended Query Table at 0x0040
[    0.316000]   Amd/Fujitsu Extended Query version 1.3.
[    0.320000] number of CFI chips: 1
[    0.324000] 5 ofpart partitions found on MTD device ltq_nor
[    0.328000] Creating 5 MTD partitions on "ltq_nor":
[    0.332000] 0x000000000000-0x000000040000 : "uboot"
[    0.340000] 0x000000040000-0x000000060000 : "uboot_env"
[    0.348000] 0x000000060000-0x000001f80000 : "linux"
[    0.352000] found squashfs behind kernel
[    0.356000] Creating 2 MTD partitions on "ltq_nor":
[    0.360000] 0x000000060000-0x00000018a1dc : "kernel"
[    0.364000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    0.380000] 0x00000018a1dc-0x000001f80000 : "rootfs"
[    0.384000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    0.400000] mtd: partition "rootfs" set to be root filesystem
[    0.404000] mtd: partition "rootfs_data" created automatically, ofs=5C0000, len=19C0000 
[    0.412000] 0x0000005c0000-0x000001f80000 : "rootfs_data"
[    0.420000] 0x000001fc0000-0x000001fe0000 : "board"
[    0.424000] 0x000001fe0000-0x000002000000 : "calibration"
[    0.468000] switch0: Atheros AR8316 switch registered on 1e180000.etop-ff
[    0.496000] libphy: ltq_mii: probed
[    0.500000] ar8316: Using port 4 as switch port
[    1.608000] eth0: attached PHY [Atheros AR8216/AR8236/AR8316] (phy_addr=1e180000.etop-ff:00, irq=-1)
[    1.616000] wdt 1f8803f0.watchdog: Init done
[    1.624000] leds-gpio gpio-leds.5: pins are not configured from the driver
[    1.636000] TCP: cubic registered
[    1.636000] NET: Registered protocol family 17
[    1.640000] 8021q: 802.1Q VLAN Support v1.8
[    1.652000] VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
[    1.660000] Freeing unused kernel memory: 196k freed
- preinit -
Press the [f] key and hit [enter] to enter failsafe mode
- regular preinit -
jffs2 not ready yet; using ramdisk
- init -

Please press Enter to activate this console. [   10.444000] Compat-drivers backport release: compat-drivers-2013-01-21-1
[   10.452000] Backport based on wireless-testing.git master-2013-02-22
[   10.456000] compat.git: wireless-testing.git
[   10.660000] cfg80211: Calling CRDA to update world regulatory domain
[   10.664000] cfg80211: World regulatory domain updated:
[   10.668000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[   10.676000] cfg80211:   (2402000 KHz - 2494000 KHz @ 40000 KHz), (500 mBi, 3000 mBm)
[   10.684000] cfg80211:   (4910000 KHz - 5835000 KHz @ 40000 KHz), (N/A, 3000 mBm)
[   11.872000] PCI: Enabling device 0000:00:0e.0 (0000 -> 0002)
[   13.452000] ieee80211 phy0: Atheros AR9280 Rev:2 mem=0xb8000000, irq=30
[   13.464000] cfg80211: Calling CRDA for country: US
[   13.464000] cfg80211: Regulatory domain changed to country: US
[   13.472000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[   13.480000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
[   13.488000] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)
[   13.496000] cfg80211:   (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   13.504000] cfg80211:   (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   13.512000] cfg80211:   (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   13.516000] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)
[   13.548000] NET: Registered protocol family 8
[   13.552000] NET: Registered protocol family 20
[   14.436000] PPP generic driver version 2.4.2
[   14.572000] tun: Universal TUN/TAP device driver, 1.6
[   14.576000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[   14.776000] ip_tables: (C) 2000-2006 Netfilter Core Team
[   14.968000] NET: Registered protocol family 24
[   15.124000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[   15.148000] ehci-platform: EHCI generic platform driver
[   15.308000] nf_conntrack version 0.5.0 (957 buckets, 3828 max)
[   17.888000] xt_time: kernel timezone is -0000
[   20.612000]þXR9-x chip found
DDR set @ 166.6MHz
Check initial DDR setting...DDR check ok... start booting...



ARCADYAN U-Boot 1.00 (Nov 10 2010 - 17:41:42)

AR9 BOARD
CLOCK CPU 333M RAM 166M
DRAM:  64 MB

 relocate_code start
 relocate_code finish.
Flash: 32 MB
In:    serial
Out:   serial
Err:   serial
Net:   
switch chip id=00001001
AR8316
amazon_s Switch

Copying boot params.....
DONE

Type "run flash_nfs" to mount root filesystem over NFS

Hit any key to stop autoboot:  3  2  1  0 
## Booting image at b0060000 ...
   Image Name:   MIPS OpenWrt Linux-3.8.7
   Created:      2013-04-17  22:45:25 UTC
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    1221020 Bytes =  1.2 MB
   Load Address: 80002000
   Entry Point:  80002000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80002000) ...
## Giving linux memsize in MB, 64

Starting kernel ...

[    0.000000] Linux version 3.8.7 (daniele@danfedvm.localdomain) (gcc version 4.6.4 (OpenWrt/Linaro GCC 4.6-2012.12 r36237) ) #1 Thu Apr 18 00:45:16 CEST 2013

[    0.000000] SoC: AR9 rev 1.2

[    0.000000] bootconsole [early0] enabled

[    0.000000] CPU revision is: 0001954c (MIPS 34Kc)

[    0.000000] MIPS: machine is WBMR - Buffalo WBMR-HP-G300H

[    0.000000] Determined physical RAM map:

[    0.000000]  memory: 04000000 @ 00000000 (usable)

[    0.000000] Initrd not found or empty - disabling initrd

[    0.000000] Zone ranges:

[    0.000000]   Normal   [mem 0x00000000-0x03ffffff]

[    0.000000] Movable zone start for each node

[    0.000000] Early memory node ranges

[    0.000000]   node   0: [mem 0x00000000-0x03ffffff]

[    0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.

[    0.000000] Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 32 bytes

[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256

[    0.000000] Kernel command line: console=ttyLTQ0,115200 init=/etc/preinit

[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)

[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)

[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)

[    0.000000] __ex_table already sorted, skipping sort

[    0.000000] Writing ErrCtl register=00001028

[    0.000000] Readback ErrCtl register=00001028

[    0.000000] Memory: 61064k/65536k available (2588k kernel code, 4472k reserved, 853k data, 196k init, 0k highmem)

[    0.000000] NR_IRQS:256

[    0.000000] CPU Clock: 333MHz

[    0.000000] Calibrating delay loop... 221.18 BogoMIPS (lpj=442368)

[    0.040000] pid_max: default: 32768 minimum: 301

[    0.044000] Mount-cache hash table entries: 512

[    0.048000] pinctrl core: initialized pinctrl subsystem

[    0.052000] NET: Registered protocol family 16

[    0.068000] pinctrl-xway 1e100b10.pinmux: Init done

[    0.072000] dma-xway 1e104100.dma: Init done - hw rev: 6, ports: 5, channels: 20

[    0.080000] PCI host bridge /fpi@10000000/pci@E105400 ranges:

[    0.084000]  MEM 0x0000000018000000..0x0000000019ffffff

[    0.088000]   IO 0x000000001ae00000..0x000000001affffff

[    0.108000] bio: create slab <bio-0> at 0

[    0.116000] usbcore: registered new interface driver usbfs

[    0.120000] usbcore: registered new interface driver hub

[    0.124000] usbcore: registered new device driver usb

[    0.128000] PCI host bridge to bus 0000:00

[    0.132000] pci_bus 0000:00: root bus resource [mem 0x18000000-0x19ffffff]

[    0.136000] pci_bus 0000:00: root bus resource [io  0x1ae00000-0x1affffff]

[    0.140000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]

[    0.144000] pci 0000:00:0e.0: BAR 0: assigned [mem 0x18000000-0x1800ffff]

[    0.148000] pci 0000:00:0e.0: SLOT:14 PIN:1 IRQ:30

[    0.152000] Switching to clocksource MIPS

[    0.160000] NET: Registered protocol family 2

[    0.164000] TCP established hash table entries: 512 (order: 0, 4096 bytes)

[    0.172000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)

[    0.180000] TCP: Hash tables configured (established 512 bind 512)

[    0.184000] TCP: reno registered

[    0.188000] UDP hash table entries: 256 (order: 0, 4096 bytes)

[    0.196000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)

[    0.200000] NET: Registered protocol family 1

[    0.204000] gptu: totally 6 16-bit timers/counters

[    0.212000] gptu: misc_register on minor 63

[    0.216000] gptu: succeeded to request irq 126

[    0.220000] gptu: succeeded to request irq 127

[    0.224000] gptu: succeeded to request irq 128

[    0.228000] gptu: succeeded to request irq 129

[    0.232000] gptu: succeeded to request irq 130

[    0.236000] gptu: succeeded to request irq 131

[    0.248000] squashfs: version 4.0 (2009/01/31) Phillip Lougher

[    0.256000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.

[    0.264000] msgmni has been set to 119

[    0.268000] io scheduler noop registered

[    0.272000] io scheduler deadline registered (default)

[    0.280000] 1e100c00.serial: ttyLTQ0 at MMIO 0x1e100c00 (irq = 112) is a lantiq,asc

[    0.288000] console [ttyLTQ0] enabled, bootconsole disabled
[    0.288000] console [ttyLTQ0] enabled, bootconsole disabled

[    0.300000] ltq_nor: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x00227e
[    0.308000] Amd/Fujitsu Extended Query Table at 0x0040
[    0.316000]   Amd/Fujitsu Extended Query version 1.3.
[    0.320000] number of CFI chips: 1
[    0.324000] 5 ofpart partitions found on MTD device ltq_nor
[    0.328000] Creating 5 MTD partitions on "ltq_nor":
[    0.332000] 0x000000000000-0x000000040000 : "uboot"
[    0.340000] 0x000000040000-0x000000060000 : "uboot_env"
[    0.348000] 0x000000060000-0x000001f80000 : "linux"
[    0.352000] found squashfs behind kernel
[    0.356000] Creating 2 MTD partitions on "ltq_nor":
[    0.360000] 0x000000060000-0x00000018a1dc : "kernel"
[    0.364000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    0.380000] 0x00000018a1dc-0x000001f80000 : "rootfs"
[    0.384000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    0.400000] mtd: partition "rootfs" set to be root filesystem
[    0.404000] mtd: partition "rootfs_data" created automatically, ofs=5C0000, len=19C0000 
[    0.412000] 0x0000005c0000-0x000001f80000 : "rootfs_data"
[    0.420000] 0x000001fc0000-0x000001fe0000 : "board"
[    0.424000] 0x000001fe0000-0x000002000000 : "calibration"
[    0.468000] switch0: Atheros AR8316 switch registered on 1e180000.etop-ff
[    0.496000] libphy: ltq_mii: probed
[    0.500000] ar8316: Using port 4 as switch port
[    1.608000] eth0: attached PHY [Atheros AR8216/AR8236/AR8316] (phy_addr=1e180000.etop-ff:00, irq=-1)
[    1.616000] wdt 1f8803f0.watchdog: Init done
[    1.624000] leds-gpio gpio-leds.5: pins are not configured from the driver
[    1.636000] TCP: cubic registered
[    1.636000] NET: Registered protocol family 17
[    1.640000] 8021q: 802.1Q VLAN Support v1.8
[    1.652000] VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
[    1.660000] Freeing unused kernel memory: 196k freed
- preinit -
Press the [f] key and hit [enter] to enter failsafe mode
- regular preinit -
jffs2 not ready yet; using ramdisk
- init -

Please press Enter to activate this console. [   10.444000] Compat-drivers backport release: compat-drivers-2013-01-21-1
[   10.452000] Backport based on wireless-testing.git master-2013-02-22
[   10.456000] compat.git: wireless-testing.git
[   10.660000] cfg80211: Calling CRDA to update world regulatory domain
[   10.664000] cfg80211: World regulatory domain updated:
[   10.668000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[   10.676000] cfg80211:   (2402000 KHz - 2494000 KHz @ 40000 KHz), (500 mBi, 3000 mBm)
[   10.684000] cfg80211:   (4910000 KHz - 5835000 KHz @ 40000 KHz), (N/A, 3000 mBm)
[   11.872000] PCI: Enabling device 0000:00:0e.0 (0000 -> 0002)
[   13.452000] ieee80211 phy0: Atheros AR9280 Rev:2 mem=0xb8000000, irq=30
[   13.464000] cfg80211: Calling CRDA for country: US
[   13.464000] cfg80211: Regulatory domain changed to country: US
[   13.472000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[   13.480000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
[   13.488000] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)
[   13.496000] cfg80211:   (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   13.504000] cfg80211:   (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   13.512000] cfg80211:   (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   13.516000] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)
[   13.548000] NET: Registered protocol family 8
[   13.552000] NET: Registered protocol family 20
[   14.436000] PPP generic driver version 2.4.2
[   14.572000] tun: Universal TUN/TAP device driver, 1.6
[   14.576000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[   14.776000] ip_tables: (C) 2000-2006 Netfilter Core Team
[   14.968000] NET: Registered protocol family 24
[   15.124000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[   15.148000] ehci-platform: EHCI generic platform driver
[   15.308000] nf_conntrack version 0.5.0 (957 buckets, 3828 max)
[   16.664000] xt_time: kernel timezone is -0000
[   18.404000] IFX MEI Version 5.00.00
[   18.452000] IFXUSB: ifxusb_hcd: version 3.2 B110801
[   18.956000] IFXUSB: USB core #0 soft-reset
[   19.160000] IFXUSB: USB core #0 soft-reset
[   19.160000] ifxusb_hcd ifxusb_hcd: IFX USB Controller
[   19.164000] ifxusb_hcd ifxusb_hcd: new USB bus registered, assigned bus number 1
[   19.172000] ifxusb_hcd ifxusb_hcd: irq 62, io mem 0xbe101000
[   19.180000] IFXUSB: Init: Power Port (0)
[   19.184000] hub 1-0:1.0: USB hub found
[   19.188000] hub 1-0:1.0: 1 port detected
[   19.192000] ifxusb_hcd ifxusb_hcd: requested GPIO 236
[   19.440000] Infineon CPE API Driver version: DSL CPE API V3.24.4.4
Didn't write all of the data.
[   21.476000] XR9-x chip found
DDR set @ 166.6MHz
Check initial DDR setting...DDR check ok... start booting...



ARCADYAN U-Boot 1.00 (Nov 10 2010 - 17:41:42)

AR9 BOARD
CLOCK CPU 333M RAM 166M
DRAM:  64 MB

 relocate_code start
 relocate_code finish.
Flash: 32 MB
In:    serial
Out:   serial
Err:   serial
Net:   
switch chip id=00001001
AR8316
amazon_s Switch

Copying boot params.....
DONE

Type "run flash_nfs" to mount root filesystem over NFS

Hit any key to stop autoboot:  3  2  1  0 
## Booting image at b0060000 ...
   Image Name:   MIPS OpenWrt Linux-3.8.7
   Created:      2013-04-17  22:45:25 UTC
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    1221020 Bytes =  1.2 MB
   Load Address: 80002000
   Entry Point:  80002000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80002000) ...
## Giving linux memsize in MB, 64

Starting kernel ...

[    0.000000] Linux version 3.8.7 (daniele@danfedvm.localdomain) (gcc version 4.6.4 (OpenWrt/Linaro GCC 4.6-2012.12 r36237) ) #1 Thu Apr 18 00:45:16 CEST 2013

[    0.000000] SoC: AR9 rev 1.2

[    0.000000] bootconsole [early0] enabled

[    0.000000] CPU revision is: 0001954c (MIPS 34Kc)

[    0.000000] MIPS: machine is WBMR - Buffalo WBMR-HP-G300H

[    0.000000] Determined physical RAM map:

[    0.000000]  memory: 04000000 @ 00000000 (usable)

[    0.000000] Initrd not found or empty - disabling initrd

[    0.000000] Zone ranges:

[    0.000000]   Normal   [mem 0x00000000-0x03ffffff]

[    0.000000] Movable zone start for each node

[    0.000000] Early memory node ranges

[    0.000000]   node   0: [mem 0x00000000-0x03ffffff]

[    0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.

[    0.000000] Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 32 bytes

[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256

[    0.000000] Kernel command line: console=ttyLTQ0,115200 init=/etc/preinit

[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)

[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)

[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)

[    0.000000] __ex_table already sorted, skipping sort

[    0.000000] Writing ErrCtl register=00001028

[    0.000000] Readback ErrCtl register=00001028

[    0.000000] Memory: 61064k/65536k available (2588k kernel code, 4472k reserved, 853k data, 196k init, 0k highmem)

[    0.000000] NR_IRQS:256

[    0.000000] CPU Clock: 333MHz

[    0.000000] Calibrating delay loop... 221.18 BogoMIPS (lpj=442368)

[    0.040000] pid_max: default: 32768 minimum: 301

[    0.044000] Mount-cache hash table entries: 512

[    0.048000] pinctrl core: initialized pinctrl subsystem

[    0.052000] NET: Registered protocol family 16

[    0.068000] pinctrl-xway 1e100b10.pinmux: Init done

[    0.072000] dma-xway 1e104100.dma: Init done - hw rev: 6, ports: 5, channels: 20

[    0.080000] PCI host bridge /fpi@10000000/pci@E105400 ranges:

[    0.084000]  MEM 0x0000000018000000..0x0000000019ffffff

[    0.088000]   IO 0x000000001ae00000..0x000000001affffff

[    0.108000] bio: create slab <bio-0> at 0

[    0.116000] usbcore: registered new interface driver usbfs

[    0.120000] usbcore: registered new interface driver hub

[    0.124000] usbcore: registered new device driver usb

[    0.128000] PCI host bridge to bus 0000:00

[    0.132000] pci_bus 0000:00: root bus resource [mem 0x18000000-0x19ffffff]

[    0.136000] pci_bus 0000:00: root bus resource [io  0x1ae00000-0x1affffff]

[    0.140000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]

[    0.144000] pci 0000:00:0e.0: BAR 0: assigned [mem 0x18000000-0x1800ffff]

[    0.148000] pci 0000:00:0e.0: SLOT:14 PIN:1 IRQ:30

[    0.152000] Switching to clocksource MIPS

[    0.160000] NET: Registered protocol family 2

[    0.164000] TCP established hash table entries: 512 (order: 0, 4096 bytes)

[    0.172000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)

[    0.180000] TCP: Hash tables configured (established 512 bind 512)

[    0.184000] TCP: reno registered

[    0.188000] UDP hash table entries: 256 (order: 0, 4096 bytes)

[    0.196000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)

[    0.200000] NET: Registered protocol family 1

[    0.204000] gptu: totally 6 16-bit timers/counters

[    0.212000] gptu: misc_register on minor 63

[    0.216000] gptu: succeeded to request irq 126

[    0.220000] gptu: succeeded to request irq 127

[    0.224000] gptu: succeeded to request irq 128

[    0.228000] gptu: succeeded to request irq 129

[    0.232000] gptu: succeeded to request irq 130

[    0.236000] gptu: succeeded to request irq 131

[    0.248000] squashfs: version 4.0 (2009/01/31) Phillip Lougher

[    0.256000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.

[    0.264000] msgmni has been set to 119

[    0.268000] io scheduler noop registered

[    0.272000] io scheduler deadline registered (default)

[    0.280000] 1e100c00.serial: ttyLTQ0 at MMIO 0x1e100c00 (irq = 112) is a lantiq,asc

[    0.288000] console [ttyLTQ0] enabled, bootconsole disabled
[    0.288000] console [ttyLTQ0] enabled, bootconsole disabled

[    0.300000] ltq_nor: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x00227e
[    0.308000] Amd/Fujitsu Extended Query Table at 0x0040
[    0.316000]   Amd/Fujitsu Extended Query version 1.3.
[    0.320000] number of CFI chips: 1
[    0.324000] 5 ofpart partitions found on MTD device ltq_nor
[    0.328000] Creating 5 MTD partitions on "ltq_nor":
[    0.332000] 0x000000000000-0x000000040000 : "uboot"
[    0.340000] 0x000000040000-0x000000060000 : "uboot_env"
[    0.348000] 0x000000060000-0x000001f80000 : "linux"
[    0.352000] found squashfs behind kernel
[    0.356000] Creating 2 MTD partitions on "ltq_nor":
[    0.360000] 0x000000060000-0x00000018a1dc : "kernel"
[    0.364000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    0.380000] 0x00000018a1dc-0x000001f80000 : "rootfs"
[    0.384000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    0.400000] mtd: partition "rootfs" set to be root filesystem
[    0.404000] mtd: partition "rootfs_data" created automatically, ofs=5C0000, len=19C0000 
[    0.412000] 0x0000005c0000-0x000001f80000 : "rootfs_data"
[    0.420000] 0x000001fc0000-0x000001fe0000 : "board"
[    0.424000] 0x000001fe0000-0x000002000000 : "calibration"
[    0.468000] switch0: Atheros AR8316 switch registered on 1e180000.etop-ff
[    0.496000] libphy: ltq_mii: probed
[    0.500000] ar8316: Using port 4 as switch port
[    1.608000] eth0: attached PHY [Atheros AR8216/AR8236/AR8316] (phy_addr=1e180000.etop-ff:00, irq=-1)
[    1.616000] wdt 1f8803f0.watchdog: Init done
[    1.624000] leds-gpio gpio-leds.5: pins are not configured from the driver
[    1.636000] TCP: cubic registered
[    1.636000] NET: Registered protocol family 17
[    1.640000] 8021q: 802.1Q VLAN Support v1.8
[    1.652000] VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
[    1.660000] Freeing unused kernel memory: 196k freed
- preinit -
Press the [f] key and hit [enter] to enter failsafe mode
- regular preinit -
jffs2 not ready yet; using ramdisk
- init -

Please press Enter to activate this console. XR9-x chip found
DDR set @ 166.6MHz
Check initial DDR setting...DDR check ok... start booting...



ARCADYAN U-Boot 1.00 (Nov 10 2010 - 17:41:42)

AR9 BOARD
CLOCK CPU 333M RAM 166M
DRAM:  64 MB

 relocate_code start
 relocate_code finish.
Flash: 32 MB
AOSS button pushed!!!  try network booting....
In:    serial
Out:   serial
Err:   serial
Net:   
switch chip id=00001001
AR8316
amazon_s Switch

Copying boot params.....
DONE
Using amazon_s Switch device
TFTP from server 192.168.11.2; our IP address is 192.168.11.1
Filename 'firmware.ram'.
Load address: 0x82000000
Loading: *T T T #################################################################
	 #################################################################
	 #################################################################
	 #################################################################
	 #################################################################
	 #################################################################
	 ########################################
done
Bytes transferred = 2199378 (218f52 hex)

## Checking Image at 82000000 ...
   Image Name:   MIPS OpenWrt Linux-3.3.8
   Created:      2012-10-18  23:08:59 UTC
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    2199314 Bytes =  2.1 MB
   Load Address: 80002000
   Entry Point:  80002000
   Verifying Checksum ... OK
## Booting image at 82000000 ...
   Image Name:   MIPS OpenWrt Linux-3.3.8
   Created:      2012-10-18  23:08:59 UTC
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    2199314 Bytes =  2.1 MB
   Load Address: 80002000
   Entry Point:  80002000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80002000) ...
## Giving linux memsize in MB, 64

Starting kernel ...

[    0.000000] Linux version 3.3.8 (fabian_wittenberg@FRadikalerMobil) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #1 Fri Oct 19 01:08:45 CEST 2012

[    0.000000] SoC: AR9 rev 1.2

[    0.000000] bootconsole [early0] enabled

[    0.000000] CPU revision is: 0001954c (MIPS 34Kc)

[    0.000000] Determined physical RAM map:

[    0.000000]  memory: 04000000 @ 00000000 (usable)

[    0.000000] Initrd not found or empty - disabling initrd

[    0.000000] Zone PFN ranges:

[    0.000000]   Normal   0x00000000 -> 0x00004000

[    0.000000] Movable zone start PFN for each node

[    0.000000] Early memory PFN ranges

[    0.000000]     0: 0x00000000 -> 0x00004000

[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256

[    0.000000] Kernel command line: console=ttyLTQ1,115200 rootfstype=squashfs,jffs2 machtype=WBMR

[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)

[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)

[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)

[    0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.

[    0.000000] Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 32 bytes

[    0.000000] Writing ErrCtl register=00011035

[    0.000000] Readback ErrCtl register=00011035

[    0.000000] Memory: 58052k/65536k available (2273k kernel code, 7484k reserved, 380k data, 4000k init, 0k highmem)

[    0.000000] NR_IRQS:256

[    0.000000] CPU Clock: 333MHz

[    0.000000] Calibrating delay loop... 221.18 BogoMIPS (lpj=442368)

[    0.036000] pid_max: default: 32768 minimum: 301

[    0.040000] Mount-cache hash table entries: 512

[    0.048000] NET: Registered protocol family 16

[    0.056000] gpiochip_add: registered GPIOs 0 to 15 on device: ltq_gpio

[    0.060000] gpiochip_add: registered GPIOs 16 to 31 on device: ltq_gpio

[    0.064000] gpiochip_add: registered GPIOs 32 to 47 on device: ltq_gpio

[    0.068000] gpiochip_add: registered GPIOs 48 to 55 on device: ltq_gpio

[    0.072000] MIPS: machine is WBMR

[    0.100000] bio: create slab <bio-0> at 0

[    0.108000] PCI host bridge to bus 0000:00

[    0.112000] pci_bus 0000:00: root bus resource [mem 0x18000000-0x19ffffff]

[    0.116000] pci_bus 0000:00: root bus resource [io  0x1ae00000-0x1affffff]

[    0.120000] pci 0000:00:0e.0: BAR 0: assigned [mem 0x18000000-0x1800ffff]

[    0.124000] pci 0000:00:0e.0: SLOT:14 PIN:1 IRQ:30

[    0.128000] Switching to clocksource MIPS

[    0.136000] NET: Registered protocol family 2

[    0.140000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)

[    0.148000] TCP established hash table entries: 2048 (order: 2, 16384 bytes)

[    0.156000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)

[    0.160000] TCP: Hash tables configured (established 2048 bind 2048)

[    0.168000] TCP reno registered

[    0.172000] UDP hash table entries: 256 (order: 0, 4096 bytes)

[    0.176000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)

[    0.184000] NET: Registered protocol family 1

[    0.324000] gptu: totally 6 16-bit timers/counters

[    0.332000] gptu: misc_register on minor 63

[    0.336000] gptu: succeeded to request irq 126

[    0.340000] gptu: succeeded to request irq 127

[    0.344000] gptu: succeeded to request irq 128

[    0.348000] gptu: succeeded to request irq 129

[    0.352000] gptu: succeeded to request irq 130

[    0.356000] gptu: succeeded to request irq 131

[    0.364000] squashfs: version 4.0 (2009/01/31) Phillip Lougher

[    0.372000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.

[    0.380000] msgmni has been set to 113

[    0.384000] io scheduler noop registered

[    0.388000] io scheduler deadline registered (default)

[    0.396000] ltq_asc.1: ttyLTQ1 at MMIO 0x1e100c00 (irq = 112) is a ltq_asc

[    0.400000] console [ttyLTQ1] enabled, bootconsole disabled
[    0.400000] console [ttyLTQ1] enabled, bootconsole disabled

[    0.416000] ltq_nor: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x00227e
[    0.424000] Amd/Fujitsu Extended Query Table at 0x0040
[    0.428000]   Amd/Fujitsu Extended Query version 1.3.
[    0.436000] number of CFI chips: 1
[    0.436000] Creating 4 MTD partitions on "ltq_nor":
[    0.444000] 0x000000000000-0x000000040000 : "uboot"
[    0.452000] 0x000000040000-0x000000060000 : "uboot-env"
[    0.456000] 0x000000060000-0x000001f80000 : "linux"
[    0.464000] found squashfs behind kernel
[    0.464000] Creating 2 MTD partitions on "ltq_nor":
[    0.472000] 0x000000060000-0x00000018a1dc : "kernel"
[    0.476000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    0.492000] 0x00000018a1dc-0x000001f80000 : "rootfs"
[    0.496000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    0.508000] mtd: partition "rootfs" set to be root filesystem
[    0.512000] mtd: partition "rootfs_data" created automatically, ofs=5C0000, len=19C0000 
[    0.520000] 0x0000005c0000-0x000001f80000 : "rootfs_data"
[    0.528000] 0x000001fe0000-0x000002000000 : "calibration"
[    0.680000] ltq_mii: probed
[    0.708000] eth0: Atheros AR8316 switch driver attached.
[    0.712000] ar8316: Using port 4 as switch port
[    5.832000] eth0: attached PHY [Atheros AR8216/AR8236/AR8316] (phy_addr=ltq_etop-fffffff:00, irq=-1)
[    5.848000] TCP cubic registered
[    5.852000] NET: Registered protocol family 17
[    5.856000] 8021q: 802.1Q VLAN Support[    5.880000] Freeing unused kernel memory: 4000k freed
- preinit -
Press the [f] key and hit [enter] to enter failsafe mode
- regular preinit -
- init -

Please press Enter to activate this console. [   10.132000] usbcore: registered new interface driver usbfs
[   10.136000] usbcore: registered new interface driver hub
[   10.144000] usbcore: registered new device driver usb
[   10.164000] NET: Registered protocol family 8
[   10.168000] NET: Registered protocol family 20
[   10.196000] Button Hotplug driver version 0.4.1
[   10.228000] PPP generic driver version 2.4.2
[   10.284000] ip_tables: (C) 2000-2006 Netfilter Core Team
[   10.428000] NET: Registered protocol family 24
[   10.448000] nf_conntrack version 0.5.0 (969 buckets, 3876 max)
[   10.672000] IFX MEI Version 5.00.00
[   10.696000] 
[   10.696000] Infineon CPE API Driver version: DSL CPE API V3.24.4.4
[   10.724000]     ATM (A1) firmware version 1.0.19
[   10.728000] ifxmips_atm: ATM init succeed
[   10.752000] dwc_otg: version 2.60a 22-NOV-2006
[   11.352000] DWC_otg: Using DMA mode
[   11.356000] dwc_otg dwc_otg.0: DWC OTG Controller
[   11.360000] dwc_otg dwc_otg.0: new USB bus registered, assigned bus number 1
[   11.368000] dwc_otg dwc_otg.0: irq 62, io mem 0xffffffffbe101000
[   11.376000] DWC_otg: Init: Port Power? op_state=1
[   11.380000] DWC_otg: Init: Power Port (0)
[   11.384000] hub 1-0:1.0: USB hub found
[   11.388000] hub 1-0:1.0: 1 port detected
[   11.408000] input: gpio-keys-polled as /devices/platform/gpio-keys-polled/input/input0
[   11.492000] DISCONNECTED PORT
[   14.248000] device eth0 entered promiscuous mode
[   14.256000] br-lan: port 1(eth0) entered forwarding state
[   14.260000] br-lan: port 1(eth0) entered forwarding state
[   16.264000] br-lan: port 1(eth0) entered forwarding state

comment:9 Changed 5 years ago by d.buffa@…

Dear OpenWRT developers, can you think that is it possible to have a solution for this issue? I cannot contribute directly, my linux programming skill is not good enough, but I can make available my time for test, and obviously I can donate...

Thanks
Daniele Buffa.

comment:10 Changed 5 years ago by anonymous

could be this:

GPIO reset button is wrongly treated as active high, fix is in ​http://patchwork.openwrt.org/patch/3633/ .

comment:11 Changed 5 years ago by d.buffa@…

Tried r37268, the issue is fixed please close it (i don't know in which revision...)

Thanks
Daniele Buffa

comment:12 Changed 4 years ago by nbd

  • Resolution set to fixed
  • Status changed from reopened to closed

Add Comment

Modify Ticket

Action
as closed .
The resolution will be deleted. Next status will be 'reopened'.
Author


E-mail address and user name can be saved in the Preferences.

 
Note: See TracTickets for help on using tickets.