Modify

Opened 5 years ago

Closed 4 years ago

Last modified 4 years ago

#13168 closed defect (no_response)

WRT54GL crashes sometimes on boot when Regulatory domain changed to DE

Reported by: s.lemke@… Owned by: developers
Priority: normal Milestone: Barrier Breaker 14.07
Component: packages Version: 10.03.1
Keywords: Cc:

Description

Hello,

Hardware: WRT54GL v1.1 (serial CL7Bxxx)
Openwrt: tested with official 10.03.1 and also 12.09-rc1

The Problem occurs sometimes on boot when "Regulatory domain changed to DE" - with the default "World" it does not appear.
It´s in 10.03.1 and also 12.09-rc1.

I have attached some files to auto-reboot the router after 60 seconds. I have done this because the issue occurs only sometimes. When using the automatic reboot it could take up to a couple of hours.

I have compiled a kernel with symbols. Here is the boot / crash log:
[...]
b44: eth0: powering down PHY
b44: eth0: Link is up at 100 Mbps, full duplex.
b44: eth0: Flow control is off for TX and off for RX.
device eth0.0 entered promiscuous mode
device eth0 entered promiscuous mode
br-lan: port 1(eth0.0) entering forwarding state
Compat-wireless backport release: compat-wireless-2011-11-08-1-g4ab9b62
Backport based on wireless-testing.git master-2011-11-15
cfg80211: Calling CRDA to update world regulatory domain
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
cfg80211: World regulatory domain updated:
cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
b43-phy0: Broadcom 5352 WLAN found (core revision 9)
Registered led device: b43-phy0::tx
Registered led device: b43-phy0::rx
Registered led device: b43-phy0::radio
Broadcom 43xx driver loaded [ Features: PL ]
Broadcom 43xx-legacy driver loaded [ Features: PLID ]
PPP generic driver version 2.4.2
ip_tables: (C) 2000-2006 Netfilter Core Team
NET: Registered protocol family 24
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
nf_conntrack version 0.5.0 (970 buckets, 3880 max)
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
ohci_hcd ssb0:1: SSB OHCI Controller
ohci_hcd ssb0:1: new USB bus registered, assigned bus number 1
ohci_hcd ssb0:1: irq 6, io mem 0x18003000
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
cfg80211: Calling CRDA for country: DE
cfg80211: Regulatory domain changed to country: DE
cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
cfg80211: (2400000 KHz - 2483500 KHz @ 40000 KHz), (N/A, 2000 mBm)
cfg80211: (5150000 KHz - 5250000 KHz @ 40000 KHz), (N/A, 2000 mBm)
cfg80211: (5250000 KHz - 5350000 KHz @ 40000 KHz), (N/A, 2000 mBm)
cfg80211: (5470000 KHz - 5725000 KHz @ 40000 KHz), (N/A, 2698 mBm)
b43-phy0: Loading firmware version 508.1084 (2009-01-14 01:32:01)
irq 5: nobody cared (try booting with the "irqpoll" option)
Call Trace:
[<8000a230>] dump_stack+0x8/0x34
[<8005aaf8>] report_bad_irq+0x5c/0xd8
[<8005acf0>] note_interrupt+0x17c/0x224
[<8005b4f4>] handle_percpu_irq+0x64/0x9c
[<8000e1ac>] plat_irq_dispatch+0x128/0x178
[<80001444>] ret_from_irq+0x0/0x4
[<8002bf5c>]
do_softirq+0x70/0x174
[<8002c0bc>] do_softirq+0x5c/0x98
[<8000e1b4>] plat_irq_dispatch+0x130/0x178
[<80001444>] ret_from_irq+0x0/0x4
[<830c3b7c>] b43_mac_suspend+0x184/0xb7c [b43]

handlers:
[<830c0a3c>] (b43_ieee80211_antenna_sanitize+0x1c4/0x1fc [b43])
Disabling IRQ #5
irq 5: nobody cared (try booting with the "irqpoll" option)
Call Trace:
[<8000a230>] dump_stack+0x8/0x34
[<8005aaf8>] report_bad_irq+0x5c/0xd8
[<8005acf0>] note_interrupt+0x17c/0x224
[<8005b4f4>] handle_percpu_irq+0x64/0x9c
[<8000e1ac>] plat_irq_dispatch+0x128/0x178
[<80001444>] ret_from_irq+0x0/0x4
[<8002bf5c>]
do_softirq+0x70/0x174
[<8002c0bc>] do_softirq+0x5c/0x98
[<8000e1b4>] plat_irq_dispatch+0x130/0x178
[<80001444>] ret_from_irq+0x0/0x4
[<830c3b7c>] b43_mac_suspend+0x184/0xb7c [b43]

Attachments (1)

RTR-Test.zip (519 bytes) - added by s.lemke@… 5 years ago.
Scripts for automatic Reboot

Download all attachments as: .zip

Change History (5)

Changed 5 years ago by s.lemke@…

Scripts for automatic Reboot

comment:1 Changed 5 years ago by hauke

Does this problem still occur in current trunk?

comment:2 Changed 4 years ago by nbd

  • Resolution set to no_response
  • Status changed from new to closed

comment:3 Changed 4 years ago by s.lemke-at-infoworxx.de

Hello,

sorry for the delay. With the current trunk of 17.9.2013 the crash is gone.

Thanks!
Sebastian

comment:4 Changed 4 years ago by jow

  • Milestone changed from Attitude Adjustment 12.09 to Barrier Breaker 14.07

Milestone Attitude Adjustment 12.09 deleted

Add Comment

Modify Ticket

Action
as closed .
The resolution will be deleted. Next status will be 'reopened'.
Author


E-mail address and user name can be saved in the Preferences.

 
Note: See TracTickets for help on using tickets.