Opened 5 years ago

Closed 3 years ago

#12222 closed defect (fixed)

RTA1025W_16 board not working

Reported by: IgorR76 Owned by: florian
Priority: normal Milestone: Barrier Breaker 14.07
Component: base system Version: Trunk
Keywords: RTA1025W_16 switch bus leds Cc:


In RTA1025W-16 board (CPU bcm6348,Eth bcm5325), OpenWrt works incorrectly. No information in /proc (cpuinfo), leds & reset button inoperative, switch with vlans cannot be accessed.

Attachments (3)

ZTE_boot.log (6.6 KB) - added by IgorR76 5 years ago.
Original ZTE Firmware boot process
OpenWrt_boot.log (10.1 KB) - added by IgorR76 5 years ago.
OpenWrt boot
dmesg.txt (12.5 KB) - added by IgorR76 5 years ago.
dmesg & ifconfig output

Download all attachments as: .zip

Change History (12)

comment:2 Changed 5 years ago by florian

Can you please attach a boot log file so we can fix this?

Changed 5 years ago by IgorR76

Original ZTE Firmware boot process

Changed 5 years ago by IgorR76

OpenWrt boot

comment:3 Changed 5 years ago by IgorR76

In original FW switch present at eth0 with ETH MAC ADDR (:::::3C)
In OpenWrt it is eth1 and MAC is from usb port (::::3D)
but it can connect to Ethernet sockets.
robocfg & swconfig says "Failed to connect to switch"...
Direct echo to led ports (b43-phy0::...) does not turn on & off leds...
This board has 6 LEDs, but only 3 presents.

comment:4 Changed 5 years ago by IgorR76

Can we use original Broadcom drivers (bcmprocfsSL2141I.o_save & bcm_enetSL2141I.o_save) instead OpenWrt 'bcm63xx_enet' ?

comment:5 Changed 5 years ago by florian

Please provide the output of "dmesg". No, we cannot use any driver from broadcom.

comment:6 Changed 5 years ago by IgorR76

Yes,of course. I'll upload the dmesg output in a few minutes, but it's the same that is in bootlog... May be you want to see output of some others commands? I'm just connected to RTA1025W-16 via serial cable.

Changed 5 years ago by IgorR76

dmesg & ifconfig output

comment:7 Changed 5 years ago by florian

  • Owner changed from developers to florian
  • Status changed from new to assigned

comment:8 Changed 5 years ago by paolo.caste@…

I have the same issue.
MY box is SL2-141-i, i changed the board to RTA1025W_16 to flash it with OpenWrt ( and after that it seems OK.
But i need to create VLANs to use 1 ethernet physical port as WAN. No need to use anymore the ADSL telephone port. WLAN is OK.

Now, i was working a lot trying to create a correct /etc/config/network file (lots of docs in web), but everytime i cannot make vlan working.
Then i noticed in/proc/switch/eth0 dir:
--> vlan_enable=0 ??
--> xxx file (don't remember) says this is a adm6996 chip.... --> not sure if there are some drivers missing
--> robotswitch module is OK

Not sure how is the architecture of this platform, i mean, if the internal switch is on eth0 or eth1... btw, i have only eth0 in /proc.

I see the previous post did not have updates.... if you request more logs, i can send them! I really want to find a solution for this!


comment:9 Changed 4 years ago by jow

  • Milestone changed from Attitude Adjustment 12.09 to Barrier Breaker 14.07

Milestone Attitude Adjustment 12.09 deleted

comment:10 Changed 3 years ago by florian

  • Resolution set to fixed
  • Status changed from assigned to closed

Add Comment

Modify Ticket

as closed .
The resolution will be deleted. Next status will be 'reopened'.

E-mail address and user name can be saved in the Preferences.

Note: See TracTickets for help on using tickets.