Modify

Opened 5 years ago

Closed 5 years ago

Last modified 4 years ago

#12146 closed defect (no_response)

rt3352 wifi ap mode up, but can not be found any ssid

Reported by: sniperpr@… Owned by: developers
Priority: low Milestone: Barrier Breaker 14.07
Component: kernel Version: Trunk
Keywords: Cc:

Description

rt3352 wifi ap mode up, but can not be found any ssid.
hardware d-link 615h1.

dd-wrt is work.

thanks.

Attachments (0)

Change History (7)

comment:1 Changed 5 years ago by sniperpr@…

r33324

wifi up
Configuration file: /var/run/hostapd-phy0.conf
[   90.810000] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 0 - CWmin: 5, CWmax: 10, Aifs: 2, TXop: 0.
[   90.830000] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 1 - CWmin: 5, CWmax: 10, Aifs: 2, TXop: 0.
[   90.850000] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 2 - CWmin: 5, CWmax: 10, Aifs: 2, TXop: 0.
[   90.860000] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 3 - CWmin: 5, CWmax: 10, Aifs: 2, TXop: 0.
[   90.900000] device wlan0 entered promiscuous mode
[   94.990000] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 0 - CWmin: 3, CWmax: 4, Aifs: 2, TXop: 102.
[   95.010000] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 1 - CWmin: 4, CWmax: 5, Aifs: 2, TXop: 188.
[   95.030000] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 2 - CWmin: 5, CWmax: 10, Aifs: 3, TXop: 0.
[   95.050000] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 3 - CWmin: 5, CWmax: 10, Aifs: 7, TXop: 0.
Using interface wlan0 with hwaddr 0e:4c:39:77:6b:74 and ssid '3352'
[   95.110000] br-lan: port 2(wlan0) entered forwarding state
[   95.120000] br-lan: port 2(wlan0) entered forwarding state
[   95.130000] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 0 - CWmin: 2, CWmax: 3, Aifs: 1, TXop: 47.
[   95.150000] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 1 - CWmin: 3, CWmax: 4, Aifs: 1, TXop: 94.
[   95.170000] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 2 - CWmin: 4, CWmax: 6, Aifs: 3, TXop: 0.
[   95.200000] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 3 - CWmin: 4, CWmax: 10, Aifs: 7, TXop: 0.
[   97.120000] br-lan: port 2(wlan0) entered forwarding state
iwconfig 
eth0.1    no wireless extensions.

lo        no wireless extensions.

wlan0     IEEE 802.11bgn  Mode:Master  Tx-Power=20 dBm   
          RTS thr:off   Fragment thr:off
          Power Management:off

comment:2 Changed 5 years ago by sniperpr@…

dmesg

 Linux version 3.3.8 (trac@UbuntuServer32) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #4 Sun Sep 9 14:22:25 CST 2012
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU revision is: 0001964c (MIPS 24KEc)
[    0.000000] Ralink RT3352 id:1 rev:4 running at 400.00 MHz
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 04000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone PFN ranges:
[    0.000000]   Normal   0x00000000 -> 0x00004000
[    0.000000] Movable zone start PFN for each node
[    0.000000] Early memory PFN ranges
[    0.000000]     0: 0x00000000 -> 0x00004000
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
[    0.000000] Kernel command line:  board=DIR-615-H1 console=ttyS1,57600 mtdparts=spi0.0:192k(u-boot)ro,64k(u-boot-env)ro,64k(factory)ro,896k(kernel),2880k(rootfs),3776k@0x50000(firmware) rootfstype=squashfs,jf2
[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 32 bytes
[    0.000000] Writing ErrCtl register=0006b6f0
[    0.000000] Readback ErrCtl register=0006b6f0
[    0.000000] Memory: 62428k/65536k available (1918k kernel code, 3108k reserved, 321k data, 172k init, 0k highmem)
[    0.000000] SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS:48
[    0.000000] console [ttyS1] enabled, bootconsole disabled
[    0.000000] console [ttyS1] enabled, bootconsole disabled
[    0.010000] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104)
[    0.090000] pid_max: default: 32768 minimum: 301
[    0.100000] Mount-cache hash table entries: 512
[    0.110000] NET: Registered protocol family 16
[    0.120000] MIPS: machine is D-Link DIR-615 H1
[    0.130000] gpiochip_add: registered GPIOs 0 to 23 on device: RT305X-GPIO0
[    0.140000] gpiochip_add: registered GPIOs 24 to 39 on device: RT305X-GPIO1
[    0.150000] gpiochip_add: registered GPIOs 40 to 51 on device: RT305X-GPIO2
[    0.170000] bio: create slab <bio-0> at 0
[    0.180000] Switching to clocksource MIPS
[    0.190000] NET: Registered protocol family 2
[    0.200000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.210000] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
[    0.230000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[    0.240000] TCP: Hash tables configured (established 2048 bind 2048)
[    0.250000] TCP reno registered
[    0.260000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.270000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.290000] NET: Registered protocol family 1
[    0.330000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.340000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.360000] msgmni has been set to 121
[    0.370000] io scheduler noop registered
[    0.380000] io scheduler deadline registered (default)
[    0.390000] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[    0.400000] serial8250: ttyS0 at MMIO 0x10000500 (irq = 13) is a 16550A
[    0.420000] serial8250: ttyS1 at MMIO 0x10000c00 (irq = 20) is a 16550A
[    0.440000] m25p80 spi0.0: found mx25l3205d, expected w25q128
[    0.450000] m25p80 spi0.0: mx25l3205d (4096 Kbytes)
[    0.460000] 6 cmdlinepart partitions found on MTD device spi0.0
[    0.470000] Creating 6 MTD partitions on "spi0.0":
[    0.480000] 0x000000000000-0x000000030000 : "u-boot"
[    0.490000] 0x000000030000-0x000000040000 : "u-boot-env"
[    0.510000] 0x000000040000-0x000000050000 : "factory"
[    0.520000] 0x000000050000-0x000000130000 : "kernel"
[    0.530000] 0x000000130000-0x000000400000 : "rootfs"
[    0.550000] mtd: partition "rootfs" set to be root filesystem
[    0.560000] mtd: partition "rootfs_data" created automatically, ofs=290000, len=170000 
[    0.570000] 0x000000290000-0x000000400000 : "rootfs_data"
[    0.590000] 0x000000050000-0x000000400000 : "firmware"
[    0.610000] ramips-wdt ramips-wdt: timeout value must be 0 < timeout <= 32, using 32
[    0.630000] TCP cubic registered
[    0.630000] NET: Registered protocol family 17
[    0.640000] 8021q: 802.1Q VLAN Support v1.8
[    0.660000] VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
[    0.680000] Freeing unused kernel memory: 172k freed
[    3.800000] input: gpio-keys-polled as /devices/platform/gpio-keys-polled/input/input0
[    3.890000] Button Hotplug driver version 0.4.1
- preinit -
Press the [f] key and hit [enter] to enter failsafe mode
- regular preinit -
[    7.540000] JFFS2 notice: (352) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (0 unchecked, 0 orphan) and 3 of xref (0 dead, 0 orphan) found.
switching to jffs2
- init -

Please press Enter to activate this console. [    8.380000] Compat-drivers backport release: compat-drivers-2012-09-04-2-gddac993
[    8.390000] Backport based on wireless-testing.git master-2012-09-07
[    8.410000] compat.git: wireless-testing.git
[    8.620000] cfg80211: Calling CRDA to update world regulatory domain
[    8.630000] cfg80211: World regulatory domain updated:
[    8.640000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[    8.660000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[    8.670000] cfg80211:   (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[    8.690000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[    8.700000] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[    8.720000] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[    9.020000] usbcore: registered new interface driver usbfs
[    9.030000] usbcore: registered new interface driver hub
[    9.050000] usbcore: registered new device driver usb
[    9.520000] phy0 -> rt2x00lib_request_eeprom_file: Info - Loading EEPROM data from 'RT305X.eeprom'.
[    9.680000] phy0 -> rt2x00_set_chip: Info - Chipset detected - rt: 3352, rf: 000c, rev: 0200.
[    9.840000] PPP generic driver version 2.4.2
[    9.910000] ip_tables: (C) 2000-2006 Netfilter Core Team
[   10.050000] NET: Registered protocol family 24
[   10.080000] nf_conntrack version 0.5.0 (978 buckets, 3912 max)
[   13.810000] device eth0.1 entered promiscuous mode
[   13.820000] device eth0 entered promiscuous mode
[   13.830000] br-lan: port 1(eth0.1) entered forwarding state
[   13.840000] br-lan: port 1(eth0.1) entered forwarding state
[   15.220000] ramips-wdt: timeout value 60 must be 0 < timeout <= 32, using 32
[   15.840000] br-lan: port 1(eth0.1) entered forwarding state
[   21.050000] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 0 - CWmin: 5, CWmax: 10, Aifs: 2, TXop: 0.
[   21.070000] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 1 - CWmin: 5, CWmax: 10, Aifs: 2, TXop: 0.
[   21.080000] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 2 - CWmin: 5, CWmax: 10, Aifs: 2, TXop: 0.
[   21.100000] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 3 - CWmin: 5, CWmax: 10, Aifs: 2, TXop: 0.
[   21.140000] device wlan0 entered promiscuous mode

comment:3 Changed 5 years ago by dani@…

i just hit the same problem, wifi seems somehow "up" but cannot really be seen from outside the router :)

using r33573 :

[ 0.000000] Linux version 3.3.8 (dani@…) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-20122
[ 0.000000] prom: fw_arg0=00000001, fw_arg1=81f4efb0, fw_arg2=01f4f3b0, fw_arg3=00000000
[ 0.000000] env[0]: memsize=32
[ 0.000000] env[1]: initrd_start=0x00000000
[ 0.000000] env[2]: initrd_size=0x0
[ 0.000000] env[3]: flash_start=0x00000000
[ 0.000000] env[4]: flash_size=0x400000
[ 0.000000] env[0]: memsize=32
[ 0.000000] env[1]: initrd_start=0x00000000
[ 0.000000] env[2]: initrd_size=0x0
[ 0.000000] env[3]: flash_start=0x00000000
[ 0.000000] env[4]: flash_size=0x400000
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU revision is: 0001964c (MIPS 24KEc)
[ 0.000000] Ralink RT3352 id:1 rev:4 running at 400.00 MHz
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 02000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone PFN ranges:
[ 0.000000] Normal 0x00000000 -> 0x00002000
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] Early memory PFN ranges
[ 0.000000] 0: 0x00000000 -> 0x00002000
[ 0.000000] On node 0 totalpages: 8192
[ 0.000000] free_area_init_node: node 0, pgdat 802315c0, node_mem_map 81000000
[ 0.000000] Normal zone: 64 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 8128 pages, LIFO batch:0
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128
[ 0.000000] Kernel command line: board=DIR-615-H1 console=ttyS1,57600 mtdparts=spi0.0:192k(u-boot)ro,64k(u2
[ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
[ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 32 bytes
[ 0.000000] Writing ErrCtl register=00049f40
[ 0.000000] Readback ErrCtl register=00049f40
[ 0.000000] Memory: 29828k/32768k available (1926k kernel code, 2940k reserved, 320k data, 164k init, 0k hi)
[ 0.000000] SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:48
[ 0.000000] console [ttyS1] enabled, bootconsole disabled
[ 0.010000] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104)
[ 0.090000] pid_max: default: 32768 minimum: 301
[ 0.100000] Mount-cache hash table entries: 512
[ 0.110000] NET: Registered protocol family 16
[ 0.120000] MIPS: machine is D-Link DIR-615 H1
[ 0.130000] gpiochip_add: registered GPIOs 0 to 23 on device: RT305X-GPIO0
[ 0.140000] gpiochip_add: registered GPIOs 24 to 39 on device: RT305X-GPIO1
[ 0.150000] gpiochip_add: registered GPIOs 40 to 51 on device: RT305X-GPIO2
[ 0.170000] bio: create slab <bio-0> at 0
[ 0.180000] Switching to clocksource MIPS
[ 0.190000] NET: Registered protocol family 2
[ 0.200000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.210000] TCP established hash table entries: 1024 (order: 1, 8192 bytes)
[ 0.230000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.240000] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.250000] TCP reno registered
[ 0.260000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.270000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.280000] NET: Registered protocol family 1
[ 0.320000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.330000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.350000] msgmni has been set to 58
[ 0.360000] io scheduler noop registered
[ 0.370000] io scheduler deadline registered (default)
[ 0.380000] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 0.390000] serial8250: ttyS0 at MMIO 0x10000500 (irq = 13) is a 16550A
[ 0.410000] serial8250: ttyS1 at MMIO 0x10000c00 (irq = 20) is a 16550A
[ 0.420000] m25p80 spi0.0: mx25l3205d (4096 Kbytes)
[ 0.430000] 6 cmdlinepart partitions found on MTD device spi0.0
[ 0.450000] Creating 6 MTD partitions on "spi0.0":
[ 0.450000] 0x000000000000-0x000000030000 : "u-boot"
[ 0.470000] 0x000000030000-0x000000040000 : "u-boot-env"
[ 0.480000] 0x000000040000-0x000000050000 : "factory"
[ 0.490000] 0x000000050000-0x000000130000 : "kernel"
[ 0.510000] 0x000000130000-0x000000400000 : "rootfs"
[ 0.520000] mtd: partition "rootfs" set to be root filesystem
[ 0.530000] mtd: partition "rootfs_data" created automatically, ofs=330000, len=D0000
[ 0.550000] 0x000000330000-0x000000400000 : "rootfs_data"
[ 0.560000] 0x000000050000-0x000000400000 : "firmware"
[ 0.580000] ramips-wdt ramips-wdt: timeout value must be 0 < timeout <= 32, using 32
[ 0.590000] TCP cubic registered
[ 0.600000] NET: Registered protocol family 17
[ 0.610000] 8021q: 802.1Q VLAN Support v1.8
[ 0.630000] VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
[ 0.640000] Freeing unused kernel memory: 164k freed
[ 3.520000] input: gpio-keys-polled as /devices/platform/gpio-keys-polled/input/input0
[ 3.630000] Button Hotplug driver version 0.4.1
[ 3.900000] Registered led device: d-link:amber:status
[ 3.900000] Registered led device: d-link:green:status
[ 3.910000] Registered led device: d-link:amber:wan
[ 3.910000] Registered led device: d-link:green:wan
[ 3.910000] Registered led device: d-link:blue:wps
[ 7.250000] JFFS2 notice: (351) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum.
[ 9.360000] Compat-drivers backport release: compat-drivers-2012-09-04-2-gddac993
[ 9.370000] Backport based on wireless-testing.git master-2012-09-07
[ 9.380000] compat.git: wireless-testing.git
[ 9.420000] cfg80211: Calling CRDA to update world regulatory domain
[ 9.430000] cfg80211: World regulatory domain updated:
[ 9.440000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 9.460000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 9.480000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 9.490000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 9.510000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 9.520000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 9.930000] NET: Registered protocol family 10
[ 10.650000] phy0 -> rt2x00lib_request_eeprom_file: Info - Loading EEPROM data from 'RT305X.eeprom'.
[ 10.800000] phy0 -> rt2x00_set_chip: Info - Chipset detected - rt: 3352, rf: 000c, rev: 0200.
[ 10.820000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 10.820000] Registered led device: rt2800pci-phy0::radio
[ 10.820000] Registered led device: rt2800pci-phy0::assoc
[ 10.820000] Registered led device: rt2800pci-phy0::quality
[ 10.870000] PPP generic driver version 2.4.2
[ 11.120000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 11.360000] NET: Registered protocol family 24
[ 11.380000] nf_conntrack version 0.5.0 (468 buckets, 1872 max)
[ 11.630000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 14.970000] ADDRCONF(NETDEV_CHANGE): eth0.1: link becomes ready
[ 14.980000] device eth0.1 entered promiscuous mode
[ 14.990000] device eth0 entered promiscuous mode
[ 15.000000] br-lan: port 1(eth0.1) entered forwarding state
[ 15.020000] br-lan: port 1(eth0.1) entered forwarding state
[ 16.700000] ramips-wdt: timeout value 60 must be 0 < timeout <= 32, using 32
[ 17.020000] br-lan: port 1(eth0.1) entered forwarding state
[ 22.960000] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 0 - CWmin: 5, CWmax: 10, Aifs: 2, TXop: 0.
[ 22.970000] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 1 - CWmin: 5, CWmax: 10, Aifs: 2, TXop: 0.
[ 22.990000] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 2 - CWmin: 5, CWmax: 10, Aifs: 2, TXop: 0.
[ 23.010000] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 3 - CWmin: 5, CWmax: 10, Aifs: 2, TXop: 0.
[ 23.050000] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 23.080000] device wlan0 entered promiscuous mode
[ 25.670000] eth0: no IPv6 routers present
[ 25.700000] eth0.2: no IPv6 routers present
[ 27.180000] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 0 - CWmin: 3, CWmax: 4, Aifs: 2, TXop: 10.
[ 27.200000] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 1 - CWmin: 4, CWmax: 5, Aifs: 2, TXop: 18.
[ 27.210000] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 2 - CWmin: 5, CWmax: 10, Aifs: 3, TXop: 0.
[ 27.230000] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 3 - CWmin: 5, CWmax: 10, Aifs: 7, TXop: 0.
[ 27.270000] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 27.420000] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 0 - CWmin: 2, CWmax: 3, Aifs: 1, TXop: 47.
[ 27.480000] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 1 - CWmin: 3, CWmax: 4, Aifs: 1, TXop: 94.
[ 27.560000] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 2 - CWmin: 4, CWmax: 6, Aifs: 3, TXop: 0.
[ 27.610000] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 3 - CWmin: 4, CWmax: 10, Aifs: 7, TXop: 0.
[ 27.700000] br-lan: port 2(wlan0) entered forwarding state
[ 27.710000] br-lan: port 2(wlan0) entered forwarding state
[ 27.720000] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 29.710000] br-lan: port 2(wlan0) entered forwarding state

root@OpenWrt:~# iwconfig wlan0
wlan0 IEEE 802.11bgn Mode:Master Tx-Power=20 dBm

RTS thr:off Fragment thr:off
Power Management:off

root@OpenWrt:~# opkg list-installed | grep kmod-rt
kmod-rt2800-lib - 3.3.8+2012-09-07-2
kmod-rt2800-pci - 3.3.8+2012-09-07-2
kmod-rt2x00-lib - 3.3.8+2012-09-07-2
kmod-rt2x00-pci - 3.3.8+2012-09-07-2
kmod-rt2x00-soc - 3.3.8+2012-09-07-2

root@OpenWrt:~# cat /etc/config/wireless
config wifi-device radio0

option type mac80211
option channel 11
option macaddr 84:c9:b2:d4:e5:dc
option hwmode 11ng
option htmode HT20
list ht_capab GF
list ht_capab SHORT-GI-20
list ht_capab SHORT-GI-40
list ht_capab TX-STBC
list ht_capab RX-STBC12
# REMOVE THIS LINE TO ENABLE WIFI:
option disabled 0

config wifi-iface

option device radio0
option network lan
option mode ap
option ssid OpenWrt
option encryption none

comment:4 Changed 5 years ago by anonymous

Same problem here with nearly same chipset:
/ticket/12432.html

Seems like the compat-wireless drivers from 09.2012 do not work with this chipset any more (older ones worked).

comment:5 Changed 5 years ago by nbd

please try current trunk

comment:6 Changed 5 years ago by nbd

  • Resolution set to no_response
  • Status changed from new to closed

comment:7 Changed 4 years ago by jow

  • Milestone changed from Attitude Adjustment 12.09 to Barrier Breaker 14.07

Milestone Attitude Adjustment 12.09 deleted

Add Comment

Modify Ticket

Action
as closed .
The resolution will be deleted. Next status will be 'reopened'.
Author


E-mail address and user name can be saved in the Preferences.

 
Note: See TracTickets for help on using tickets.