Ticket #9554: dmesg.log

File dmesg.log, 8.8 KB (added by Troex Nevelin <troex@…>, 7 years ago)
Line 
1root@nikopol:~# dmesg
2Linux version 2.6.32.25 (openwrt@ampere) (gcc version 4.3.3 (GCC) ) #1 Fri Nov 19 22:01:56 PST 2010
3CPU revision is: 00029029 (Broadcom BCM3302)
4ssb: Core 0 found: ChipCommon (cc 0x800, rev 0x14, vendor 0x4243)
5ssb: Core 1 found: Fast Ethernet (cc 0x806, rev 0x09, vendor 0x4243)
6ssb: Core 2 found: MIPS 3302 (cc 0x816, rev 0x08, vendor 0x4243)
7ssb: Core 3 found: USB 2.0 Host (cc 0x819, rev 0x02, vendor 0x4243)
8ssb: Core 4 found: MEMC SDRAM (cc 0x80F, rev 0x04, vendor 0x4243)
9ssb: Core 5 found: IEEE 802.11 (cc 0x812, rev 0x0D, vendor 0x4243)
10ssb: Core 6 found: Roboswitch (cc 0x81C, rev 0x02, vendor 0x4243)
11ssb: chipcommon status is 0x0
12ssb: Found rev 0 PMU (capabilities 0x04A63400)
13ssb: Initializing MIPS core...
14ssb: set_irq: core 0x0806, irq 4 => 4
15ssb: set_irq: core 0x0816, irq 5 => 2
16ssb: set_irq: core 0x0812, irq 2 => 5
17ssb: after irq reconfiguration
18ssb: core 0x0800, irq : 2(S)  3* 4  5  6  D  I
19ssb: core 0x0806, irq : 2(S)  3  4* 5  6  D  I
20ssb: core 0x0816, irq : 2(S)* 3  4  5  6  D  I
21ssb: core 0x0819, irq : 2(S)  3  4  5  6* D  I
22ssb: core 0x080f, irq : 2(S)  3  4  5  6  D  I*
23ssb: core 0x0812, irq : 2(S)  3  4  5* 6  D  I
24ssb: core 0x081c, irq : 2(S)  3  4  5  6  D  I*
25ssb: Sonics Silicon Backplane found at address 0x18000000
26Serial init done.
27Determined physical RAM map:
28 memory: 02000000 @ 00000000 (usable)
29Initrd not found or empty - disabling initrd
30Zone PFN ranges:
31  Normal   0x00000000 -> 0x00002000
32Movable zone start PFN for each node
33early_node_map[1] active PFN ranges
34    0: 0x00000000 -> 0x00002000
35On node 0 totalpages: 8192
36free_area_init_node: node 0, pgdat 802a09f0, node_mem_map 81000000
37  Normal zone: 64 pages used for memmap
38  Normal zone: 0 pages reserved
39  Normal zone: 8128 pages, LIFO batch:0
40Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 8128
41Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
42PID hash table entries: 128 (order: -3, 512 bytes)
43Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
44Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
45Primary instruction cache 16kB, VIPT, 4-way, linesize 16 bytes.
46Primary data cache 16kB, 2-way, VIPT, cache aliases, linesize 16 bytes
47Memory: 29496k/32768k available (2331k kernel code, 3272k reserved, 356k data, 136k init, 0k highmem)
48Hierarchical RCU implementation.
49NR_IRQS:128
50console [ttyS0] enabled
51Calibrating delay loop... 239.61 BogoMIPS (lpj=479232)
52Mount-cache hash table entries: 512
53NET: Registered protocol family 16
54bio: create slab <bio-0> at 0
55Switching to clocksource MIPS
56NET: Registered protocol family 2
57IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
58TCP established hash table entries: 1024 (order: 1, 8192 bytes)
59TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
60TCP: Hash tables configured (established 1024 bind 1024)
61TCP reno registered
62NET: Registered protocol family 1
63squashfs: version 4.0 (2009/01/31) Phillip Lougher
64Registering mini_fo version $Id$
65JFFS2 version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
66msgmni has been set to 57
67io scheduler noop registered
68io scheduler deadline registered (default)
69Serial: 8250/16550 driver, 2 ports, IRQ sharing enabled
70serial8250: ttyS0 at MMIO 0xb8000300 (irq = 3) is a 16550A
71serial8250: ttyS1 at MMIO 0xb8000400 (irq = 3) is a 16550A
72serial8250.0: ttyS0 at MMIO 0xb8000300 (irq = 3) is a 16550A
73serial8250.0: ttyS1 at MMIO 0xb8000400 (irq = 3) is a 16550A
74flash init: 0x1c000000 0x02000000
75Physically mapped flash: Found 1 x16 devices at 0x0 in 8-bit bank
76Physically mapped flash: Found an alias at 0x400000 for the chip at 0x0
77Physically mapped flash: Found an alias at 0x800000 for the chip at 0x0
78Physically mapped flash: Found an alias at 0xc00000 for the chip at 0x0
79Physically mapped flash: Found an alias at 0x1000000 for the chip at 0x0
80Physically mapped flash: Found an alias at 0x1400000 for the chip at 0x0
81Physically mapped flash: Found an alias at 0x1800000 for the chip at 0x0
82Physically mapped flash: Found an alias at 0x1c00000 for the chip at 0x0
83 CFI mfr 0x00000001
84 CFI id  0x00001a01
85 Amd/Fujitsu Extended Query Table at 0x0040
86  Amd/Fujitsu Extended Query version 1.3.
87Physically mapped flash: Swapping erase regions for broken CFI table.
88number of CFI chips: 1
89cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
90Flash device: 0x400000 at 0x1fc00000
91bootloader size: 262144
92Creating 4 MTD partitions on "Physically mapped flash":
930x000000000000-0x000000040000 : "cfe"
940x000000040000-0x0000003f0000 : "linux"
950x00000011b000-0x0000003f0000 : "rootfs"
96mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
97mtd: partition "rootfs" set to be root filesystem
98mtd: partition "rootfs_data" created automatically, ofs=2F0000, len=100000
990x0000002f0000-0x0000003f0000 : "rootfs_data"
1000x0000003f0000-0x000000400000 : "nvram"
101b44.c:v2.0
102eth0: Broadcom 44xx/47xx 10/100BaseT Ethernet 00:90:4c:c0:00:00
103BCM47xx Watchdog Timer enabled (30 seconds, nowayout)
104TCP westwood registered
105NET: Registered protocol family 17
106802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
107All bugs added by David S. Miller <davem@redhat.com>
108VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
109Freeing unused kernel memory: 136k freed
110Please be patient, while OpenWrt loads ...
111diag: Detected 'D-Link DIR-320'
112b44: eth0: Link is up at 100 Mbps, full duplex.
113b44: eth0: Flow control is off for TX and off for RX.
114roboswitch: Probing device eth0: found a 5325! It's a 5350.
115mini_fo: using base directory: /
116mini_fo: using storage directory: /overlay
117b44: eth0: powering down PHY
118b44: eth0: Link is up at 100 Mbps, full duplex.
119b44: eth0: Flow control is off for TX and off for RX.
120device eth0.0 entered promiscuous mode
121device eth0 entered promiscuous mode
122br-lan: port 1(eth0.0) entering forwarding state
123Compat-wireless backport release: compat-wireless-2010-10-14-7-gab01eca
124Backport based on wireless-testing.git master-2010-10-19
125cfg80211: Calling CRDA to update world regulatory domain
126usbcore: registered new interface driver usbfs
127usbcore: registered new interface driver hub
128usbcore: registered new device driver usb
129b43-phy0: Broadcom 5354 WLAN found (core revision 13)
130cfg80211: World regulatory domain updated:
131    (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
132    (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
133    (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
134    (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
135    (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
136    (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
137ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
138Registered led device: b43-phy0::tx
139Registered led device: b43-phy0::rx
140Registered led device: b43-phy0::radio
141Broadcom 43xx driver loaded [ Features: PL, GPIO LED Mask: 0x000f, Firmware-ID: FW13 ]
142Broadcom 43xx-legacy driver loaded [ Features: PLID, Firmware-ID: FW10 ]
143PPP generic driver version 2.4.2
144ip_tables: (C) 2000-2006 Netfilter Core Team
145NET: Registered protocol family 24
146ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
147nf_conntrack version 0.5.0 (463 buckets, 1852 max)
148CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
149nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or
150sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
151ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
152ohci_hcd ssb0:1: SSB OHCI Controller
153ohci_hcd ssb0:1: new USB bus registered, assigned bus number 1
154ohci_hcd ssb0:1: irq 6, io mem 0x18003000
155usb usb1: configuration #1 chosen from 1 choice
156hub 1-0:1.0: USB hub found
157hub 1-0:1.0: 2 ports detected
158ohci_hcd ssb0:1: SSB EHCI Controller
159ohci_hcd ssb0:1: new USB bus registered, assigned bus number 2
160ohci_hcd ssb0:1: irq 6, io mem 0x18003800
161ohci_hcd ssb0:1: USB 0.0 started, EHCI 1.00
162usb usb2: configuration #1 chosen from 1 choice
163hub 2-0:1.0: USB hub found
164hub 2-0:1.0: 2 ports detected
165usbcore: registered new interface driver usbserial
166USB Serial support registered for generic
167usbcore: registered new interface driver usbserial_generic
168usbserial: USB Serial Driver core
169USB Serial support registered for pl2303
170usbcore: registered new interface driver pl2303
171pl2303: Prolific PL2303 USB to serial adaptor driver
172usb 1-1: new full speed USB device using ohci_hcd and address 2
173usb 1-1: configuration #1 chosen from 1 choice
174pl2303 1-1:1.0: pl2303 converter detected
175usb 1-1: pl2303 converter now attached to ttyUSB0
176b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
177b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
178device wlan0 entered promiscuous mode
179br-lan: port 2(wlan0) entering forwarding state
180device wlan0 left promiscuous mode
181br-lan: port 2(wlan0) entering disabled state
182device wlan0 entered promiscuous mode
183br-lan: port 2(wlan0) entering forwarding state
184