Ticket #9476: kerrnel.log

File kerrnel.log, 10.2 KB (added by anonymous, 7 years ago)
Line 
1Linux version 2.6.32.25 (openwrt@ampere) (gcc version 4.3.3 (GCC) ) #1 Fri Nov 19 22:01:56 PST 2010
2CPU revision is: 00029029 (Broadcom BCM3302)
3ssb: Core 0 found: ChipCommon (cc 0x800, rev 0x14, vendor 0x4243)
4ssb: Core 1 found: Fast Ethernet (cc 0x806, rev 0x09, vendor 0x4243)
5ssb: Core 2 found: MIPS 3302 (cc 0x816, rev 0x08, vendor 0x4243)
6ssb: Core 3 found: USB 2.0 Host (cc 0x819, rev 0x02, vendor 0x4243)
7ssb: Core 4 found: MEMC SDRAM (cc 0x80F, rev 0x04, vendor 0x4243)
8ssb: Core 5 found: IEEE 802.11 (cc 0x812, rev 0x0D, vendor 0x4243)
9ssb: Core 6 found: Roboswitch (cc 0x81C, rev 0x02, vendor 0x4243)
10ssb: chipcommon status is 0x0
11ssb: Found rev 0 PMU (capabilities 0x04A63400)
12ssb: Initializing MIPS core...
13ssb: set_irq: core 0x0806, irq 4 => 4
14ssb: set_irq: core 0x0816, irq 5 => 2
15ssb: set_irq: core 0x0812, irq 2 => 5
16ssb: after irq reconfiguration
17ssb: core 0x0800, irq : 2(S)  3* 4  5  6  D  I
18ssb: core 0x0806, irq : 2(S)  3  4* 5  6  D  I
19ssb: core 0x0816, irq : 2(S)* 3  4  5  6  D  I
20ssb: core 0x0819, irq : 2(S)  3  4  5  6* D  I
21ssb: core 0x080f, irq : 2(S)  3  4  5  6  D  I*
22ssb: core 0x0812, irq : 2(S)  3  4  5* 6  D  I
23ssb: core 0x081c, irq : 2(S)  3  4  5  6  D  I*
24ssb: Sonics Silicon Backplane found at address 0x18000000
25Serial init done.
26Determined physical RAM map:
27 memory: 02000000 @ 00000000 (usable)
28Initrd not found or empty - disabling initrd
29Zone PFN ranges:
30  Normal   0x00000000 -> 0x00002000
31Movable zone start PFN for each node
32early_node_map[1] active PFN ranges
33    0: 0x00000000 -> 0x00002000
34On node 0 totalpages: 8192
35free_area_init_node: node 0, pgdat 802a09f0, node_mem_map 81000000
36  Normal zone: 64 pages used for memmap
37  Normal zone: 0 pages reserved
38  Normal zone: 8128 pages, LIFO batch:0
39Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 8128
40Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
41PID hash table entries: 128 (order: -3, 512 bytes)
42Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
43Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
44Primary instruction cache 16kB, VIPT, 4-way, linesize 16 bytes.
45Primary data cache 16kB, 2-way, VIPT, cache aliases, linesize 16 bytes
46Memory: 29496k/32768k available (2331k kernel code, 3272k reserved, 356k data, 136k init, 0k highmem)
47Hierarchical RCU implementation.
48NR_IRQS:128
49console [ttyS0] enabled
50Calibrating delay loop... 239.61 BogoMIPS (lpj=479232)
51Mount-cache hash table entries: 512
52NET: Registered protocol family 16
53bio: create slab <bio-0> at 0
54Switching to clocksource MIPS
55NET: Registered protocol family 2
56IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
57TCP established hash table entries: 1024 (order: 1, 8192 bytes)
58TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
59TCP: Hash tables configured (established 1024 bind 1024)
60TCP reno registered
61NET: Registered protocol family 1
62squashfs: version 4.0 (2009/01/31) Phillip Lougher
63Registering mini_fo version $Id$
64JFFS2 version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
65msgmni has been set to 57
66io scheduler noop registered
67io scheduler deadline registered (default)
68Serial: 8250/16550 driver, 2 ports, IRQ sharing enabled
69serial8250: ttyS0 at MMIO 0xb8000300 (irq = 3) is a 16550A
70serial8250: ttyS1 at MMIO 0xb8000400 (irq = 3) is a 16550A
71serial8250.0: ttyS0 at MMIO 0xb8000300 (irq = 3) is a 16550A
72serial8250.0: ttyS1 at MMIO 0xb8000400 (irq = 3) is a 16550A
73flash init: 0x1c000000 0x02000000
74Physically mapped flash: Found 1 x16 devices at 0x0 in 16-bit bank
75Physically mapped flash: Found an alias at 0x800000 for the chip at 0x0
76Physically mapped flash: Found an alias at 0x1000000 for the chip at 0x0
77Physically mapped flash: Found an alias at 0x1800000 for the chip at 0x0
78 CFI mfr 0x000000c2
79 CFI id  0x000022cb
80 Amd/Fujitsu Extended Query Table at 0x0040
81  Amd/Fujitsu Extended Query version 1.1.
82number of CFI chips: 1
83cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
84Flash device: 0x800000 at 0x1fc00000
85bootloader size: 131072
86Creating 4 MTD partitions on "Physically mapped flash":
870x000000000000-0x000000020000 : "cfe"
880x000000020000-0x0000007f0000 : "linux"
890x0000000fb000-0x0000007f0000 : "rootfs"
90mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
91mtd: partition "rootfs" set to be root filesystem
92mtd: partition "rootfs_data" created automatically, ofs=2D0000, len=520000
930x0000002d0000-0x0000007f0000 : "rootfs_data"
940x0000007f0000-0x000000800000 : "nvram"
95b44.c:v2.0
96eth0: Broadcom 44xx/47xx 10/100BaseT Ethernet 00:22:15:78:77:62
97BCM47xx Watchdog Timer enabled (30 seconds, nowayout)
98TCP westwood registered
99NET: Registered protocol family 17
100802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
101All bugs added by David S. Miller <davem@redhat.com>
102VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
103Freeing unused kernel memory: 136k freed
104Please be patient, while OpenWrt loads ...
105diag: Detected 'ASUS WL-500g Premium V2'
106b44: eth0: Link is up at 100 Mbps, full duplex.
107b44: eth0: Flow control is off for TX and off for RX.
108roboswitch: Probing device eth0: found a 5325! It's a 5350.
109mini_fo: using base directory: /
110mini_fo: using storage directory: /overlay
111b44: eth0: powering down PHY
112b44: eth0: Link is up at 100 Mbps, full duplex.
113b44: eth0: Flow control is off for TX and off for RX.
114device eth0.0 entered promiscuous mode
115device eth0 entered promiscuous mode
116br-lan: port 1(eth0.0) entering forwarding state
117Compat-wireless backport release: compat-wireless-2010-10-14-7-gab01eca
118Backport based on wireless-testing.git master-2010-10-19
119cfg80211: Calling CRDA to update world regulatory domain
120IMQ driver loaded successfully.
121        Hooking IMQ before NAT on PREROUTING.
122        Hooking IMQ after NAT on POSTROUTING.
123b43-phy0: Broadcom 5354 WLAN found (core revision 13)
124ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
125Registered led device: b43-phy0::tx
126Registered led device: b43-phy0::rx
127Broadcom 43xx driver loaded [ Features: PL, GPIO LED Mask: 0x000f, Firmware-ID: FW13 ]
128cfg80211: World regulatory domain updated:
129    (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
130    (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
131    (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
132    (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
133    (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
134    (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
135Broadcom 43xx-legacy driver loaded [ Features: PLID, Firmware-ID: FW10 ]
136PPP generic driver version 2.4.2
137ip_tables: (C) 2000-2006 Netfilter Core Team
138NET: Registered protocol family 24
139nf_conntrack version 0.5.0 (463 buckets, 1852 max)
140CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
141nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or
142sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
143xt_time: kernel timezone is -0000
144b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
145b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
146device wlan0 entered promiscuous mode
147br-lan: port 2(wlan0) entering forwarding state
148device wlan0 left promiscuous mode
149br-lan: port 2(wlan0) entering disabled state
150device wlan0 entered promiscuous mode
151br-lan: port 2(wlan0) entering forwarding state
152b43-phy0 ERROR: DMA RX buffer too small (len: 42390, buffer: 2352, nr-dropped: 19)
153b43-phy0 ERROR: DMA RX buffer too small (len: 25505, buffer: 2352, nr-dropped: 11)
154b43-phy0 ERROR: DMA RX buffer too small (len: 19022, buffer: 2352, nr-dropped: 9)
155b43-phy0 ERROR: DMA RX buffer too small (len: 4189, buffer: 2352, nr-dropped: 2)
156b43-phy0 ERROR: DMA RX buffer too small (len: 37381, buffer: 2352, nr-dropped: 16)
157skb_over_panic: text:80c9a408 len:2378 put:2378 head:80eef000 data:80eef040 tail:0x80eef98a end:0x80eef980 dev:<NULL>
158Kernel bug detected[#1]:
159Cpu 0
160$ 0   : 00000000 1000b800 0000007c 00000001
161$ 4   : 80293498 000020ed ffffffff 000020ed
162$ 8   : 00004000 00000000 00000001 ffffffff
163$12   : 0000000f 80253c78 ffffffff 00000000
164$16   : 00eef040 0000092c 80eef040 819e0740
165$20   : 81b3cb00 0000001e a1b4a1e0 80c9f978
166$24   : 00000002 80166250                 
167$28   : 81a46000 81a47db0 00000020 801a3d24
168Hi    : 00000000
169Lo    : 00000077
170epc   : 801a3d24 0x801a3d24
171    Not tainted
172ra    : 801a3d24 0x801a3d24
173Status: 1000b803    KERNEL EXL IE
174Cause : 00800024
175PrId  : 00029029 (Broadcom BCM3302)
176Modules linked in: xt_IMQ nf_nat_tftp nf_conntrack_tftp nf_nat_irc nf_conntrack_irc nf_nat_ftp nf_conntrack_ftp xt_HL xt_hl xt_MARK ipt_ECN xt_CLASSIFY xt_time xt_tcpmss xt_statistic xt_mark xt_length ipt_ecn xt_DSCP xt_dscp xt_string xt_layer7 ipt_MASQUERADE iptable_nat nf_nat xt_CONNMARK xt_recent xt_helper xt_conntrack xt_connmark xt_connbytes xt_NOTRACK iptable_raw xt_state nf_conntrack_ipv4 nf_defrag_ipv4 nf_conntrack pppoe pppox ipt_REJECT xt_TCPMSS ipt_LOG xt_comment xt_multiport xt_mac xt_limit iptable_mangle iptable_filter ip_tables xt_tcpudp x_tables ppp_async ppp_generic slhc b43legacy sch_red b43 sch_sfq sch_hfsc cls_fw imq mac80211 ts_fsm ts_bm ts_kmp crc_ccitt cfg80211 compat_firmware_class compat arc4 aes_generic deflate ecb cbc switch_robo switch_core diag
177Process irq/5-b43 (pid: 895, threadinfo=81a46000, task=81ab45d0, tls=00000000)
178Stack : 00000000 80c9a408 0000094a 0000094a 80eef000 80eef040 80eef98a 80eef980
179        8026e09c 0000001e a1b4a1e0 80c9a408 80c17ad4 00ff0000 000000e6 00010000
180        819e2400 819e2400 80d31568 00ff0000 80c9f978 00010000 00010000 819e2400
181        00008000 00010000 81b3ca24 00010000 802ce8c0 00000000 802953b4 80c872cc
182        00010000 802ce8c0 80292f28 8001ce0c 819ea138 819ea138 80292f28 8001eba0
183        ...
184Call Trace:[<80c9a408>] 0x80c9a408
185[<80c9a408>] 0x80c9a408
186[<80c872cc>] 0x80c872cc
187[<8001ce0c>] 0x8001ce0c
188[<8001eba0>] 0x8001eba0
189[<8001cef8>] 0x8001cef8
190[<80190bf4>] 0x80190bf4
191[<80c87424>] 0x80c87424
192[<80057480>] 0x80057480
193[<8000af98>] 0x8000af98
194[<80057304>] 0x80057304
195[<80057304>] 0x80057304
196[<8003db30>] 0x8003db30
197[<8000f86c>] 0x8000f86c
198[<8003dab4>] 0x8003dab4
199[<8000f85c>] 0x8000f85c
200
201
202Code: afab001c  0c0028ff  afa20020 <0200000d> 08068f4a  00000000  8fbf002c  01201021  03e00008
203Disabling lock debugging due to kernel taint
204exiting task "irq/5-b43" (895) is an active IRQ thread (irq 5)