Ticket #7630: netgear-8.09-dmesg-lspci-other.txt

File netgear-8.09-dmesg-lspci-other.txt, 17.9 KB (added by realopty, 8 years ago)

dmesg / lspci of kamikaze 8.09 working wifi

Line 
1root@OpenWrt:/tmp# dmesg
2CPU revision is: 00029006
3Primary instruction cache 16kB, physically tagged, 2-way, linesize 16 bytes.
4Primary data cache 16kB, 2-way, linesize 16 bytes.
5Linux version 2.4.35.4 (will@bedroom) (gcc version 3.4.6 (OpenWrt-2.0)) #3 Thu Aug 5 20:55:42 MST 2010
6Setting the PFC to its default value
7Determined physical RAM map:
8 memory: 01000000 @ 00000000 (usable)
9On node 0 totalpages: 4096
10zone(0): 4096 pages.
11zone(1): 0 pages.
12zone(2): 0 pages.
13Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 init=/etc/preinit noinitrd console=ttyS0,115200
14CPU: BCM4704 rev 9 at 264 MHz
15Using 132.000 MHz high precision timer.
16Calibrating delay loop... 263.78 BogoMIPS
17Memory: 14256k/16384k available (1430k kernel code, 2128k reserved, 96k data, 84k init, 0k highmem)
18Dentry cache hash table entries: 2048 (order: 2, 16384 bytes)
19Inode cache hash table entries: 1024 (order: 1, 8192 bytes)
20Mount cache hash table entries: 512 (order: 0, 4096 bytes)
21Buffer cache hash table entries: 1024 (order: 0, 4096 bytes)
22Page-cache hash table entries: 4096 (order: 2, 16384 bytes)
23Checking for 'wait' instruction...  unavailable.
24POSIX conformance testing by UNIFIX
25PCI: Initializing host
26PCI: Enabling CardBus
27PCI: Fixing up bus 0
28PCI: Fixing up bridge
29PCI: Setting latency timer of device 01:00.0 to 64
30PCI: Fixing up bus 1
31Linux NET4.0 for Linux 2.4
32Based upon Swansea University Computer Society NET3.039
33Initializing RT netlink socket
34Starting kswapd
35Registering mini_fo version $Id$
36devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
37devfs: boot_options: 0x1
38JFFS2 version 2.1. (C) 2001 Red Hat, Inc., designed by Axis Communications AB.
39squashfs: version 3.0 (2006/03/15) Phillip Lougher
40pty: 256 Unix98 ptys configured
41Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled
42ttyS00 at 0xb8000300 (irq = 3) is a 16550A
43ttyS01 at 0xb8000400 (irq = 3) is a 16550A
44b44.c:v0.93 (Mar, 2004)
45PCI: Setting latency timer of device 00:01.0 to 64
46eth0: Broadcom 47xx 10/100BaseT Ethernet 00:22:3f:7c:4b:76
47PCI: Setting latency timer of device 00:02.0 to 64
48eth1: Broadcom 47xx 10/100BaseT Ethernet 00:22:3f:7c:4b:77
49Physically mapped flash: Found an alias at 0x400000 for the chip at 0x0
50Physically mapped flash: Found an alias at 0x800000 for the chip at 0x0
51Physically mapped flash: Found an alias at 0xc00000 for the chip at 0x0
52Physically mapped flash: Found an alias at 0x1000000 for the chip at 0x0
53Physically mapped flash: Found an alias at 0x1400000 for the chip at 0x0
54Physically mapped flash: Found an alias at 0x1800000 for the chip at 0x0
55Physically mapped flash: Found an alias at 0x1c00000 for the chip at 0x0
56 Amd/Fujitsu Extended Query Table v1.1 at 0x0040
57number of CFI chips: 1
58cfi_cmdset_0002: Disabling fast programming due to code brokenness.
59Flash device: 0x400000 at 0x1c000000
60bootloader size: 131072
61Physically mapped flash: Filesystem type: squashfs, size=0x177784
62Updating TRX offsets and length:
63old trx = [0x0000001c, 0x00000904, 0x0007b400], len=0x00211000 crc32=0x4ee31e50
64new trx = [0x0000001c, 0x00000904, 0x0007b400], len=0x00200000 crc32=0xad80b4dd
65Done
66Creating 5 MTD partitions on "Physically mapped flash":
670x00000000-0x00020000 : "cfe"
680x00020000-0x003f0000 : "linux"
690x0009b400-0x00220000 : "rootfs"
70mtd: partition "rootfs" doesn't start on an erase block boundary -- force read-only
710x003f0000-0x00400000 : "nvram"
720x00220000-0x003f0000 : "rootfs_data"
73Initializing Cryptographic API
74NET4: Linux TCP/IP 1.0 for NET4.0
75IP Protocols: ICMP, UDP, TCP, IGMP
76IP: routing cache hash table of 512 buckets, 4Kbytes
77TCP: Hash tables configured (established 1024 bind 2048)
78Linux IP multicast router 0.06 plus PIM-SM
79NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
80NET4: Ethernet Bridge 008 for NET4.0
81802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
82All bugs added by David S. Miller <davem@redhat.com>
83VFS: Mounted root (squashfs filesystem) readonly.
84Mounted devfs on /dev
85Freeing unused kernel memory: 84k freed
86Algorithmics/MIPS FPU Emulator v1.5
87diag: Router model not detected.
88b44: eth0: Link is up at 100 Mbps, full duplex.
89b44: eth0: Flow control is off for TX and off for RX.
90roboswitch: Probing device eth0: found!
91mini_fo: using base directory: /
92mini_fo: using storage directory: /tmp/root
93jffs2.bbc: SIZE compression mode activated.
94b44: eth0: Link is up at 100 Mbps, full duplex.
95b44: eth0: Flow control is off for TX and off for RX.
96device eth0 entered promiscuous mode
97br-lan: port 1(eth0) entering learning state
98br-lan: port 1(eth0) entering forwarding state
99br-lan: topology change detected, propagating
100b44: eth1: Link is up at 100 Mbps, full duplex.
101b44: eth1: Flow control is off for TX and off for RX.
102b44: eth1: Link is up at 100 Mbps, full duplex.
103b44: eth1: Flow control is off for TX and off for RX.
104br-lan: port 1(eth0) entering disabled state
105br-lan: port 1(eth0) entering learning state
106br-lan: port 1(eth0) entering forwarding state
107br-lan: topology change detected, propagating
108PCI: Setting latency timer of device 01:01.0 to 64
109PCI: Enabling device 01:01.0 (0004 -> 0006)
110PCI/DMA
111wl0: wlc_attach: chiprev 1 coreunit 0 corerev 11 cccap 0x864000d maccap 0x0 band 2.4G, phy_type 4 phy_rev 1 ana_rev 5
112wl0: Broadcom BCM4321 802.11 Wireless Controller 4.150.10.5
113CSLIP: code copyright 1989 Regents of the University of California
114PPP generic driver version 2.4.2
115ip_tables: (C) 2000-2002 Netfilter core team
116ip_conntrack version 2.1 (5953 buckets, 5953 max) - 336 bytes per conntrack
117jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
118jffs2_build_filesystem(): unlocking the mtd device... done.
119jffs2_build_filesystem(): erasing all blocks after the end marker... done.
120mini_fo: using base directory: /
121mini_fo: using storage directory: /jffs
122device wl0 entered promiscuous mode
123wl0: attempt to add interface with same source address.
124br-lan: port 2(wl0) entering learning state
125br-lan: port 2(wl0) entering forwarding state
126br-lan: topology change detected, propagating
127br-lan: port 2(wl0) entering disabled state
128br-lan: port 2(wl0) entering disabled state
129device wl0 left promiscuous mode
130device wl0 entered promiscuous mode
131wl0: attempt to add interface with same source address.
132br-lan: port 2(wl0) entering learning state
133br-lan: port 2(wl0) entering forwarding state
134br-lan: topology change detected, propagating
135br-lan: port 2(wl0) entering disabled state
136br-lan: port 2(wl0) entering disabled state
137device wl0 left promiscuous mode
138device wl0 entered promiscuous mode
139wl0: attempt to add interface with same source address.
140br-lan: port 2(wl0) entering learning state
141br-lan: port 2(wl0) entering forwarding state
142br-lan: topology change detected, propagating
143br-lan: port 2(wl0) entering disabled state
144br-lan: port 1(eth0) entering disabled state
145br-lan: port 2(wl0) entering disabled state
146device wl0 left promiscuous mode
147br-lan: port 1(eth0) entering disabled state
148device eth0 left promiscuous mode
149b44: eth0: Link is up at 100 Mbps, full duplex.
150b44: eth0: Flow control is off for TX and off for RX.
151b44: eth0: Link is up at 100 Mbps, full duplex.
152b44: eth0: Flow control is off for TX and off for RX.
153device eth0 entered promiscuous mode
154br-lan: port 1(eth0) entering learning state
155br-lan: port 1(eth0) entering forwarding state
156br-lan: topology change detected, propagating
157device wl0 entered promiscuous mode
158wl0: attempt to add interface with same source address.
159br-lan: port 2(wl0) entering learning state
160br-lan: port 2(wl0) entering forwarding state
161br-lan: topology change detected, propagating
162br-lan: port 2(wl0) entering disabled state
163br-lan: port 1(eth0) entering disabled state
164br-lan: port 2(wl0) entering learning state
165br-lan: port 1(eth0) entering learning state
166br-lan: port 2(wl0) entering forwarding state
167br-lan: topology change detected, propagating
168br-lan: port 1(eth0) entering forwarding state
169br-lan: topology change detected, propagating
170b44: eth1: Link is up at 100 Mbps, full duplex.
171b44: eth1: Flow control is off for TX and off for RX.
172b44: eth1: Link is up at 100 Mbps, full duplex.
173b44: eth1: Flow control is off for TX and off for RX.
174b44: eth1: Link is up at 100 Mbps, full duplex.
175b44: eth1: Flow control is off for TX and off for RX.
176br-lan: port 2(wl0) entering disabled state
177br-lan: port 2(wl0) entering disabled state
178device wl0 left promiscuous mode
179device wl0 entered promiscuous mode
180wl0: attempt to add interface with same source address.
181br-lan: port 2(wl0) entering learning state
182br-lan: port 2(wl0) entering forwarding state
183br-lan: topology change detected, propagating
184br-lan: port 2(wl0) entering disabled state
185br-lan: port 2(wl0) entering disabled state
186device wl0 left promiscuous mode
187device wl0 entered promiscuous mode
188wl0: attempt to add interface with same source address.
189br-lan: port 2(wl0) entering learning state
190br-lan: port 2(wl0) entering forwarding state
191br-lan: topology change detected, propagating
192br-lan: port 2(wl0) entering disabled state
193br-lan: port 2(wl0) entering disabled state
194device wl0 left promiscuous mode
195device wl0 entered promiscuous mode
196wl0: attempt to add interface with same source address.
197br-lan: port 2(wl0) entering learning state
198br-lan: port 2(wl0) entering forwarding state
199br-lan: topology change detected, propagating
200br-lan: port 2(wl0) entering disabled state
201br-lan: port 2(wl0) entering disabled state
202device wl0 left promiscuous mode
203device wl0 entered promiscuous mode
204wl0: attempt to add interface with same source address.
205br-lan: port 2(wl0) entering learning state
206br-lan: port 2(wl0) entering forwarding state
207br-lan: topology change detected, propagating
208root@OpenWrt:/tmp#
209root@OpenWrt:/tmp# lspci -vv
21000:00.0 FLASH memory: Broadcom Corporation Sentry5 Chipcommon I/O Controller (rev 09)
211        Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
212        Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
213        Interrupt: pin ? routed to IRQ 3
214        Region 0: Memory at 18000000 (32-bit, non-prefetchable) [disabled] [size=4K]
215        Region 1: Memory at 1fc00000 (32-bit, non-prefetchable) [disabled] [size=4M]
216        Region 2: Memory at 1c000000 (32-bit, non-prefetchable) [disabled] [size=32M]
217        Region 3: Memory at 1a000000 (32-bit, non-prefetchable) [disabled] [size=32M]
218        Expansion ROM at <unassigned> [disabled] [size=2K]
219
22000:01.0 Ethernet controller: Broadcom Corporation Sentry5 Ethernet Controller (rev 09)
221        Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
222        Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
223        Latency: 64
224        Interrupt: pin A routed to IRQ 4
225        Region 0: Memory at 18001000 (32-bit, non-prefetchable) [disabled] [size=4K]
226        Expansion ROM at <unassigned> [disabled] [size=2K]
227
22800:02.0 Ethernet controller: Broadcom Corporation Sentry5 Ethernet Controller (rev 09)
229        Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
230        Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
231        Latency: 64
232        Interrupt: pin B routed to IRQ 5
233        Region 0: Memory at 18002000 (32-bit, non-prefetchable) [disabled] [size=4K]
234        Expansion ROM at <unassigned> [disabled] [size=2K]
235
23600:03.0 USB Controller: Broadcom Corporation Sentry5 USB Controller (rev 09) (prog-if 10 [OHCI])
237        Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
238        Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
239        Interrupt: pin C routed to IRQ 6
240        Region 0: Memory at 18003000 (32-bit, non-prefetchable) [disabled] [size=4K]
241        Expansion ROM at <unassigned> [disabled] [size=2K]
242
24300:04.0 PCI bridge: Broadcom Corporation Sentry5 PCI Bridge (rev 09) (prog-if 00 [Normal decode])
244        Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
245        Status: Cap+ 66MHz+ UDF+ FastB2B+ ParErr+ DEVSEL=?? >TAbort+ <TAbort+ <MAbort+ >SERR+ <PERR+ INTx+
246        Region 0: Memory at 18004000 (32-bit, non-prefetchable) [disabled] [size=4K]
247        Region 1: Memory at 08000000 (32-bit, non-prefetchable) [disabled] [size=128M]
248        Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
249        I/O behind bridge: 00000000-00000fff
250        Memory behind bridge: 00000000-000fffff
251        Prefetchable memory behind bridge: 00000000-000fffff
252        Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
253        Expansion ROM at <unassigned> [disabled] [size=2K]
254        BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
255                PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
256
25700:05.0 MIPS: Broadcom Corporation BCM3302 Sentry5 MIPS32 CPU (rev 09)
258        Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
259        Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
260        Interrupt: pin E routed to IRQ 2
261        Region 0: Memory at 18005000 (32-bit, non-prefetchable) [disabled] [size=4K]
262        Expansion ROM at <unassigned> [disabled] [size=2K]
263
26400:06.0 Modem: Broadcom Corporation BCM47xx V.92 56k modem (rev 09) (prog-if 00 [Generic])
265        Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
266        Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
267        Interrupt: pin F routed to IRQ 2
268        Region 0: Memory at 18006000 (32-bit, non-prefetchable) [disabled] [size=4K]
269        Expansion ROM at <unassigned> [disabled] [size=2K]
270
27100:07.0 Network and computing encryption device: Broadcom Corporation Sentry5 Crypto Accelerator (rev 09)
272        Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
273        Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
274        Interrupt: pin G routed to IRQ 2
275        Region 0: Memory at 18007000 (32-bit, non-prefetchable) [disabled] [size=4K]
276        Expansion ROM at <unassigned> [disabled] [size=2K]
277
27800:08.0 RAM memory: Broadcom Corporation Sentry5 DDR/SDR RAM Controller (rev 09)
279        Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
280        Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
281        Interrupt: pin ? routed to IRQ 3
282        Region 0: Memory at 18008000 (32-bit, non-prefetchable) [disabled] [size=4K]
283        Region 1: Memory at <unassigned> (32-bit, non-prefetchable) [disabled] [size=128M]
284        Region 2: Memory at 10000000 (32-bit, non-prefetchable) [disabled] [size=128M]
285        Region 3: Memory at 80000000 (32-bit, non-prefetchable) [disabled] [size=512M]
286        Expansion ROM at <unassigned> [disabled] [size=2K]
287
28801:00.0 Host bridge: Broadcom Corporation BCM4704 PCI to SB Bridge (rev 09)
289        Subsystem: Broadcom Corporation BCM4704 PCI to SB Bridge
290        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
291        Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
292        Latency: 64
293        Interrupt: pin A routed to IRQ 2
294        Region 0: Memory at 40000000 (32-bit, non-prefetchable) [size=8K]
295        Region 1: Memory at <unassigned> (32-bit, prefetchable) [size=128M]
296
29701:01.0 Network controller: Broadcom Corporation BCM4306 802.11a Wireless LAN Controller (rev 01)
298        Subsystem: Broadcom Corporation BCM4306 802.11a Wireless LAN Controller
299        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
300        Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
301        Latency: 64
302        Interrupt: pin A routed to IRQ 2
303        Region 0: Memory at 40004000 (32-bit, non-prefetchable) [size=16K]
304
305root@OpenWrt:/tmp# wifi detect
306root@OpenWrt:/tmp# wifi
307Command 'set rxant' failed: -1
308root@OpenWrt:/tmp# ifconfig
309br-lan    Link encap:Ethernet  HWaddr 00:22:3F:7C:4B:76 
310          inet addr:10.0.0.2  Bcast:10.255.255.255  Mask:255.0.0.0
311          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
312          RX packets:3126 errors:0 dropped:0 overruns:0 frame:0
313          TX packets:2644 errors:0 dropped:0 overruns:0 carrier:0
314          collisions:0 txqueuelen:0
315          RX bytes:656324 (640.9 KiB)  TX bytes:270087 (263.7 KiB)
316
317eth0      Link encap:Ethernet  HWaddr 00:22:3F:7C:4B:76 
318          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
319          RX packets:4948 errors:0 dropped:0 overruns:0 frame:0
320          TX packets:3640 errors:0 dropped:0 overruns:0 carrier:0
321          collisions:0 txqueuelen:1000
322          RX bytes:931246 (909.4 KiB)  TX bytes:399372 (390.0 KiB)
323          Interrupt:4
324
325eth1      Link encap:Ethernet  HWaddr 00:22:3F:7C:4B:77 
326          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
327          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
328          TX packets:508 errors:0 dropped:0 overruns:0 carrier:0
329          collisions:0 txqueuelen:1000
330          RX bytes:0 (0.0 B)  TX bytes:206248 (201.4 KiB)
331          Interrupt:5
332
333lo        Link encap:Local Loopback 
334          inet addr:127.0.0.1  Mask:255.0.0.0
335          UP LOOPBACK RUNNING  MTU:16436  Metric:1
336          RX packets:52 errors:0 dropped:0 overruns:0 frame:0
337          TX packets:52 errors:0 dropped:0 overruns:0 carrier:0
338          collisions:0 txqueuelen:0
339          RX bytes:4096 (4.0 KiB)  TX bytes:4096 (4.0 KiB)
340
341wl0       Link encap:Ethernet  HWaddr 00:22:3F:7C:4B:76 
342          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
343          RX packets:245 errors:0 dropped:0 overruns:0 frame:8760
344          TX packets:711 errors:788 dropped:0 overruns:0 carrier:0
345          collisions:0 txqueuelen:1000
346          RX bytes:36127 (35.2 KiB)  TX bytes:106174 (103.6 KiB)
347          Interrupt:2 Base address:0x4000
348