Ticket #7604: openwrt-dmsg

File openwrt-dmsg, 10.0 KB (added by realopty , 8 years ago)

dmsg

Line 
1Linux version 2.6.34.1 (will@ubuntu) (gcc version 4.3.3 (GCC) ) #1 Mon Jul 12 10:54:46 MDT 2010
2CPU revision is: 00029006 (Broadcom BCM3302)
3ssb: Core 0 found: ChipCommon (cc 0x800, rev 0x03, vendor 0x4243)
4ssb: Core 1 found: Fast Ethernet (cc 0x806, rev 0x06, vendor 0x4243)
5ssb: Core 2 found: Fast Ethernet (cc 0x806, rev 0x06, vendor 0x4243)
6ssb: Core 3 found: USB 1.1 Hostdev (cc 0x808, rev 0x02, vendor 0x4243)
7ssb: Core 4 found: PCI (cc 0x804, rev 0x08, vendor 0x4243)
8ssb: Core 5 found: MIPS 3302 (cc 0x816, rev 0x00, vendor 0x4243)
9ssb: Core 6 found: V90 (cc 0x807, rev 0x02, vendor 0x4243)
10ssb: Core 7 found: IPSEC (cc 0x80B, rev 0x00, vendor 0x4243)
11ssb: Core 8 found: MEMC SDRAM (cc 0x80F, rev 0x00, vendor 0x4243)
12ssb: Sonics Silicon Backplane found at address 0x18000000
13Serial init done.
14Determined physical RAM map:
15 memory: 02000000 @ 00000000 (usable)
16Initrd not found or empty - disabling initrd
17Zone PFN ranges:
18  Normal   0x00000000 -> 0x00002000
19Movable zone start PFN for each node
20early_node_map[1] active PFN ranges
21    0: 0x00000000 -> 0x00002000
22On node 0 totalpages: 8192
23free_area_init_node: node 0, pgdat 8026c1f0, node_mem_map 81000000
24  Normal zone: 64 pages used for memmap
25  Normal zone: 0 pages reserved
26  Normal zone: 8128 pages, LIFO batch:0
27Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 8128
28Kernel command line:  root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
29PID hash table entries: 128 (order: -3, 512 bytes)
30Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
31Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
32Primary instruction cache 16kB, VIPT, 2-way, linesize 16 bytes.
33Primary data cache 16kB, 2-way, VIPT, cache aliases, linesize 16 bytes
34Memory: 29728k/32768k available (2158k kernel code, 3040k reserved, 319k data, 144k init, 0k highmem)
35NR_IRQS:128
36console [ttyS0] enabled
37Calibrating delay loop... 263.16 BogoMIPS (lpj=526336)
38Mount-cache hash table entries: 512
39NET: Registered protocol family 16
40bio: create slab <bio-0> at 0
41Switching to clocksource MIPS
42PCI: Fixing up bridge 0000:00:00.0
43PCI: Setting latency timer of device 0000:00:00.0 to 64
44PCI: Fixing up device 0000:00:00.0
45PCI: Fixing latency timer of device 0000:00:00.0 to 168
46pci 0000:00:00.0: reg 10: [mem 0x00000000-0x00001fff]
47pci 0000:00:00.0: reg 14: [mem 0x00000000-0x07ffffff pref]
48pci 0000:00:02.0: reg 10: [io  0x0410-0x0417]
49pci 0000:00:02.0: reg 14: [io  0x0420-0x0423]
50pci 0000:00:02.0: reg 18: [io  0x0418-0x041f]
51pci 0000:00:02.0: reg 1c: [io  0x0424-0x0427]
52pci 0000:00:02.0: reg 20: [io  0x0400-0x040f]
53pci 0000:00:02.0: reg 30: [mem 0x00000000-0x0000ffff pref]
54pci 0000:00:02.0: supports D1 D2
55pci 0000:00:03.0: reg 10: [mem 0x00000000-0x00000fff]
56pci 0000:00:03.0: PME# supported from D0 D1 D3hot D3cold
57pci 0000:00:03.0: PME# disabled
58pci 0000:00:03.3: reg 10: [mem 0x00000000-0x000000ff]
59pci 0000:00:03.3: PME# supported from D0 D3hot D3cold
60pci 0000:00:03.3: PME# disabled
61pci 0000:00:02.0: BAR 6: assigned [mem 0x40000000-0x4000ffff pref]
62pci 0000:00:03.0: BAR 0: assigned [mem 0x40010000-0x40010fff]
63pci 0000:00:03.0: BAR 0: set to [mem 0x40010000-0x40010fff] (PCI address [0x40010000-0x40010fff]
64pci 0000:00:03.3: BAR 0: assigned [mem 0x40011000-0x400110ff]
65pci 0000:00:03.3: BAR 0: set to [mem 0x40011000-0x400110ff] (PCI address [0x40011000-0x400110ff]
66pci 0000:00:02.0: BAR 4: assigned [io  0x0400-0x040f]
67pci 0000:00:02.0: BAR 4: set to [io  0x0400-0x040f] (PCI address [0x400-0x40f]
68pci 0000:00:02.0: BAR 0: assigned [io  0x0410-0x0417]
69pci 0000:00:02.0: BAR 0: set to [io  0x0410-0x0417] (PCI address [0x410-0x417]
70pci 0000:00:02.0: BAR 2: assigned [io  0x0418-0x041f]
71pci 0000:00:02.0: BAR 2: set to [io  0x0418-0x041f] (PCI address [0x418-0x41f]
72pci 0000:00:02.0: BAR 1: assigned [io  0x0420-0x0423]
73pci 0000:00:02.0: BAR 1: set to [io  0x0420-0x0423] (PCI address [0x420-0x423]
74pci 0000:00:02.0: BAR 3: assigned [io  0x0424-0x0427]
75pci 0000:00:02.0: BAR 3: set to [io  0x0424-0x0427] (PCI address [0x424-0x427]
76NET: Registered protocol family 2
77IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
78TCP established hash table entries: 1024 (order: 1, 8192 bytes)
79TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
80TCP: Hash tables configured (established 1024 bind 1024)
81TCP reno registered
82UDP hash table entries: 256 (order: 0, 4096 bytes)
83UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
84NET: Registered protocol family 1
85PCI: CLS 0 bytes, default 32
86init_vdso successfull
87squashfs: version 4.0 (2009/01/31) Phillip Lougher
88Registering mini_fo version $Id$
89JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
90msgmni has been set to 58
91io scheduler noop registered
92io scheduler deadline registered (default)
93Serial: 8250/16550 driver, 2 ports, IRQ sharing enabled
94serial8250: ttyS0 at MMIO 0xb8000300 (irq = 3) is a 16550A
95serial8250: ttyS1 at MMIO 0xb8000400 (irq = 3) is a 16550A
96serial8250.0: ttyS0 at MMIO 0xb8000300 (irq = 3) is a 16550A
97serial8250.0: ttyS1 at MMIO 0xb8000400 (irq = 3) is a 16550A
98flash init: 0x1c000000 0x02000000
99Physically mapped flash: Found 1 x16 devices at 0x0 in 16-bit bank
100Physically mapped flash: Found an alias at 0x800000 for the chip at 0x0
101Physically mapped flash: Found an alias at 0x1000000 for the chip at 0x0
102Physically mapped flash: Found an alias at 0x1800000 for the chip at 0x0
103 CFI mfr 0x00000001
104 CFI id  0x00001301
105 Amd/Fujitsu Extended Query Table at 0x0040
106  Amd/Fujitsu Extended Query version 1.3.
107Physically mapped flash: CFI does not contain boot bank location. Assuming top.
108number of CFI chips: 1
109Flash device: 0x800000 at 0x1fc00000
110bootloader size: 262144
111Looking for dual image
112Creating 4 MTD partitions on "Physically mapped flash":
1130x000000000000-0x000000040000 : "cfe"
1140x000000040000-0x0000007f0000 : "linux"
1150x00000010c400-0x0000007f0000 : "rootfs"
116mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
117mtd: partition "rootfs" set to be root filesystem
118mtd: partition "rootfs_data" created automatically, ofs=250000, len=5A0000
1190x000000250000-0x0000007f0000 : "rootfs_data"
1200x0000007f0000-0x000000800000 : "nvram"
121b44: b44.c:v2.0
122b44 ssb0:0: eth0: Broadcom 44xx/47xx 10/100BaseT Ethernet 00:01:6c:f4:c7:7a
123b44 ssb0:1: eth1: Broadcom 44xx/47xx 10/100BaseT Ethernet 40:01:6c:f4:c7:7a
124BCM47xx Watchdog Timer enabled (30 seconds, nowayout)
125TCP westwood registered
126NET: Registered protocol family 17
127802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
128All bugs added by David S. Miller <davem@redhat.com>
129VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
130Freeing unused kernel memory: 144k freed
131diag: Detected 'SimpleTech SimpleShare NAS'
132diag: Spinning up HDD and enabling leds
133b44 ssb0:0: eth0: Link is up at 100 Mbps, full duplex
134b44 ssb0:0: eth0: Flow control is off for TX and off for RX
135Uniform Multi-Platform E-IDE driver
136SCSI subsystem initialized
137usbcore: registered new interface driver usbfs
138usbcore: registered new interface driver hub
139usbcore: registered new device driver usb
140PCI: Enabling device 0000:00:02.0 (0000 -> 0001)
141PCI: Fixing up device 0000:00:02.0
142aec62xx 0000:00:02.0: IDE controller (0x1191:0x0008 rev 0x07)
143aec62xx 0000:00:02.0: 100% native mode on irq 6
144PCI: Setting latency timer of device 0000:00:02.0 to 64
145    ide0: BM-DMA at 0x0400-0x0407
146    ide1: BM-DMA at 0x0408-0x040f
147Probing IDE interface ide0...
148hda: WDC WD2500JB-00REA0, ATA DISK drive
149hda: host max PIO4 wanted PIO255(auto-tune) selected PIO4
150hda: host side 80-wire cable detection failed, limiting max speed to UDMA33
151hda: UDMA/33 mode selected
152Probing IDE interface ide1...
153ide0 at 0x410-0x417,0x422 on irq 6
154ide1 at 0x418-0x41f,0x426 on irq 6
155ide-gd driver 1.18
156hda: max request size: 512KiB
157hda: 488397168 sectors (250059 MB) w/8192KiB Cache, CHS=30401/255/63
158hda: cache flushes supported
159 hda: hda1
160ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
161PCI: Enabling device 0000:00:03.3 (0000 -> 0002)
162PCI: Fixing up device 0000:00:03.3
163ehci_hcd 0000:00:03.3: EHCI Host Controller
164ehci_hcd 0000:00:03.3: new USB bus registered, assigned bus number 1
165ehci_hcd 0000:00:03.3: debug port 1
166ehci_hcd 0000:00:03.3: Enabling legacy PCI PM
167ehci_hcd 0000:00:03.3: irq 6, io mem 0x40011000
168ehci_hcd 0000:00:03.3: USB 2.0 started, EHCI 1.00
169hub 1-0:1.0: USB hub found
170hub 1-0:1.0: 6 ports detected
171Initializing USB Mass Storage driver...
172usbcore: registered new interface driver usb-storage
173USB Mass Storage support registered.
174kjournald starting.  Commit interval 5 seconds
175EXT3-fs (hda1): using internal journal
176EXT3-fs (hda1): mounted filesystem with writeback data mode
177mini_fo: using base directory: /
178mini_fo: using storage directory: /overlay
179b44 ssb0:0: eth0: powering down PHY
180b44 ssb0:0: eth0: powering down PHY
181PPP generic driver version 2.4.2
182NET: Registered protocol family 24
183b44 ssb0:0: eth0: Link is up at 100 Mbps, full duplex
184b44 ssb0:0: eth0: Flow control is off for TX and off for RX
185b44 ssb0:0: eth0: Link is down
186b44 ssb0:0: eth0: Link is up at 100 Mbps, half duplex
187b44 ssb0:0: eth0: Flow control is off for TX and off for RX
188b44 ssb0:0: eth0: Link is down
189b44 ssb0:0: eth0: Link is up at 100 Mbps, full duplex
190b44 ssb0:0: eth0: Flow control is off for TX and off for RX
191b44 ssb0:0: eth0: powering down PHY
192b44 ssb0:0: eth0: powering down PHY
193b44 ssb0:0: eth0: powering down PHY
194b44 ssb0:0: eth0: Link is up at 100 Mbps, full duplex
195b44 ssb0:0: eth0: Flow control is off for TX and off for RX
196b44 ssb0:0: eth0: Link is down
197b44 ssb0:0: eth0: Link is up at 10 Mbps, full duplex
198b44 ssb0:0: eth0: Flow control is off for TX and off for RX
199b44 ssb0:0: eth0: Link is down
200b44 ssb0:0: eth0: Link is up at 10 Mbps, full duplex
201b44 ssb0:0: eth0: Flow control is off for TX and off for RX
202b44 ssb0:0: eth0: Link is down
203b44 ssb0:0: eth0: Link is up at 10 Mbps, half duplex
204b44 ssb0:0: eth0: Flow control is off for TX and off for RX
205b44 ssb0:0: eth0: Link is down
206b44 ssb0:0: eth0: Link is up at 10 Mbps, full duplex
207b44 ssb0:0: eth0: Flow control is off for TX and off for RX
208b44 ssb0:0: eth0: Link is down
209b44 ssb0:0: eth0: Link is up at 100 Mbps, half duplex
210b44 ssb0:0: eth0: Flow control is off for TX and off for RX
211