Ticket #22178: dmesg.txt

File dmesg.txt, 24.7 KB (added by ferrets@…, 22 months ago)

full dmesg log

Line 
1root@Belkin:~# dmesg
2[    0.000000] Linux version 3.18.23 (buildbot@builder1) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r47269) ) #1 Sun Jan 31 18:39:35 CET 2016
3[    0.000000] MyLoader: sysp=6969e915, boardp=69612f36, parts=69e9f997
4[    0.000000] bootconsole [early0] enabled
5[    0.000000] CPU0 revision is: 00019750 (MIPS 74Kc)
6[    0.000000] SoC: Qualcomm Atheros QCA9558 ver 1 rev 0
7[    0.000000] Determined physical RAM map:
8[    0.000000]  memory: 08000000 @ 00000000 (usable)
9[    0.000000] Initrd not found or empty - disabling initrd
10[    0.000000] Zone ranges:
11[    0.000000]   Normal   [mem 0x00000000-0x07ffffff]
12[    0.000000] Movable zone start for each node
13[    0.000000] Early memory node ranges
14[    0.000000]   node   0: [mem 0x00000000-0x07ffffff]
15[    0.000000] Initmem setup node 0 [mem 0x00000000-0x07ffffff]
16[    0.000000] On node 0 totalpages: 32768
17[    0.000000] free_area_init_node: node 0, pgdat 803762b0, node_mem_map 81000000
18[    0.000000]   Normal zone: 256 pages used for memmap
19[    0.000000]   Normal zone: 0 pages reserved
20[    0.000000]   Normal zone: 32768 pages, LIFO batch:7
21[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
22[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
23[    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
24[    0.000000] pcpu-alloc: [0] 0
25[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32512
26[    0.000000] Kernel command line:  board=F9K1115V2 console=ttyS0,115200 mtdparts=spi0.0:256k(u-boot)ro,64k(u-boot-env),14464k(rootfs),1408k(kernel),64k(nvram)ro,64k(envram)ro,64k(art)ro,15872k@0x50000(firmware) rootfstype=squashfs,jffs2 noinitrd
27[    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
28[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
29[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
30[    0.000000] Writing ErrCtl register=00000000
31[    0.000000] Readback ErrCtl register=00000000
32[    0.000000] Memory: 125788K/131072K available (2586K kernel code, 128K rwdata, 540K rodata, 256K init, 193K bss, 5284K reserved)
33[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
34[    0.000000] NR_IRQS:51
35[    0.000000] Clocks: CPU:720.000MHz, DDR:600.000MHz, AHB:200.000MHz, Ref:40.000MHz
36[    0.000000] Calibrating delay loop... 358.80 BogoMIPS (lpj=1794048)
37[    0.060000] pid_max: default: 32768 minimum: 301
38[    0.060000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
39[    0.070000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
40[    0.070000] NET: Registered protocol family 16
41[    0.080000] MIPS: machine is Belkin AC1750DB
42[    0.520000] registering PCI controller with io_map_base unset
43[    0.520000] registering PCI controller with io_map_base unset
44[    0.530000] PCI host bridge to bus 0000:00
45[    0.530000] pci_bus 0000:00: root bus resource [mem 0x10000000-0x11ffffff]
46[    0.540000] pci_bus 0000:00: root bus resource [io  0x0000]
47[    0.540000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
48[    0.550000] pci 0000:00:00.0: [168c:003c] type 00 class 0x028000
49[    0.550000] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit]
50[    0.550000] pci 0000:00:00.0: reg 0x30: [mem 0x00000000-0x0000ffff pref]
51[    0.550000] pci 0000:00:00.0: supports D1
52[    0.550000] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
53[    0.550000] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
54[    0.550000] pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x101fffff 64bit]
55[    0.550000] pci 0000:00:00.0: BAR 6: assigned [mem 0x10200000-0x1020ffff pref]
56[    0.560000] PCI host bridge to bus 0000:01
57[    0.560000] pci_bus 0000:01: root bus resource [mem 0x12000000-0x13ffffff]
58[    0.570000] pci_bus 0000:01: root bus resource [io  0x0001]
59[    0.570000] pci_bus 0000:01: No busn resource found for root bus, will use [bus 01-ff]
60[    0.580000] pci 0000:01:00.0: [1b6f:7023] type 00 class 0x0c0330
61[    0.580000] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x00007fff 64bit]
62[    0.580000] pci 0000:01:00.0: supports D1 D2
63[    0.580000] pci 0000:01:00.0: PME# supported from D0 D1 D2 D3hot
64[    0.580000] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
65[    0.580000] pci 0000:01:00.0: BAR 0: assigned [mem 0x12000000-0x12007fff 64bit]
66[    0.580000] pci 0000:00:00.0: using irq 40 for pin 1
67[    0.590000] pci 0000:01:00.0: using irq 41 for pin 1
68[    0.590000] Switched to clocksource MIPS
69[    0.600000] NET: Registered protocol family 2
70[    0.600000] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
71[    0.600000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
72[    0.610000] TCP: Hash tables configured (established 1024 bind 1024)
73[    0.610000] TCP: reno registered
74[    0.620000] UDP hash table entries: 256 (order: 0, 4096 bytes)
75[    0.620000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
76[    0.630000] NET: Registered protocol family 1
77[    0.630000] PCI: CLS 0 bytes, default 32
78[    0.630000] futex hash table entries: 256 (order: -1, 3072 bytes)
79[    0.650000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
80[    0.650000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
81[    0.670000] msgmni has been set to 245
82[    0.680000] io scheduler noop registered
83[    0.680000] io scheduler deadline registered (default)
84[    0.680000] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
85[    0.690000] console [ttyS0] disabled
86[    0.720000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11, base_baud = 2500000) is a 16550A
87[    0.720000] console [ttyS0] enabled
88[    0.730000] bootconsole [early0] disabled
89[    0.740000] m25p80 spi0.0: found w25q128, expected m25p80
90[    0.750000] m25p80 spi0.0: w25q128 (16384 Kbytes)
91[    0.750000] 8 cmdlinepart partitions found on MTD device spi0.0
92[    0.760000] Creating 8 MTD partitions on "spi0.0":
93[    0.770000] 0x000000000000-0x000000040000 : "u-boot"
94[    0.770000] 0x000000040000-0x000000050000 : "u-boot-env"
95[    0.780000] 0x000000050000-0x000000e70000 : "rootfs"
96[    0.780000] mtd: device 2 (rootfs) set to be root filesystem
97[    0.790000] 1 squashfs-split partitions found on MTD device rootfs
98[    0.790000] 0x0000002d0000-0x000000e70000 : "rootfs_data"
99[    0.800000] 0x000000e70000-0x000000fd0000 : "kernel"
100[    0.810000] 0x000000fd0000-0x000000fe0000 : "nvram"
101[    0.810000] 0x000000fe0000-0x000000ff0000 : "envram"
102[    0.820000] 0x000000ff0000-0x000001000000 : "art"
103[    0.820000] 0x000000050000-0x000000fd0000 : "firmware"
104[    0.840000] switch0: Atheros AR8337 rev. 2 switch registered on ag71xx-mdio.0
105[    0.930000] libphy: ag71xx_mdio: probed
106[    1.530000] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.0:00 [uid=004dd036, driver=Atheros AR8216/AR8236/AR8316]
107[    1.540000] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:RGMII
108[    2.130000] eth1: Atheros AG71xx at 0xba000000, irq 5, mode:SGMII
109[    2.130000] TCP: cubic registered
110[    2.140000] NET: Registered protocol family 17
111[    2.140000] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
112[    2.150000] Bridge firewalling registered
113[    2.160000] 8021q: 802.1Q VLAN Support v1.8
114[    2.170000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
115[    2.180000] Freeing unused kernel memory: 256K (80390000 - 803d0000)
116[    3.220000] init: Console is alive
117[    3.230000] init: - watchdog -
118[    4.570000] usbcore: registered new interface driver usbfs
119[    4.570000] usbcore: registered new interface driver hub
120[    4.580000] usbcore: registered new device driver usb
121[    4.590000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
122[    4.590000] ehci-platform: EHCI generic platform driver
123[    4.600000] ehci-platform ehci-platform.0: EHCI Host Controller
124[    4.610000] ehci-platform ehci-platform.0: new USB bus registered, assigned bus number 1
125[    4.620000] ehci-platform ehci-platform.0: TX-TX IDP fix enabled
126[    4.620000] ehci-platform ehci-platform.0: irq 48, io mem 0x1b000000
127[    4.650000] ehci-platform ehci-platform.0: USB 2.0 started, EHCI 1.00
128[    4.650000] hub 1-0:1.0: USB hub found
129[    4.660000] hub 1-0:1.0: 1 port detected
130[    4.660000] ehci-platform ehci-platform.1: EHCI Host Controller
131[    4.670000] ehci-platform ehci-platform.1: new USB bus registered, assigned bus number 2
132[    4.680000] ehci-platform ehci-platform.1: TX-TX IDP fix enabled
133[    4.680000] ehci-platform ehci-platform.1: irq 49, io mem 0x1b400000
134[    4.710000] ehci-platform ehci-platform.1: USB 2.0 started, EHCI 1.00
135[    4.710000] hub 2-0:1.0: USB hub found
136[    4.720000] hub 2-0:1.0: 1 port detected
137[    4.730000] PCI: Enabling device 0000:01:00.0 (0000 -> 0002)
138[    4.730000] xhci_hcd 0000:01:00.0: xHCI Host Controller
139[    4.740000] xhci_hcd 0000:01:00.0: new USB bus registered, assigned bus number 3
140[    4.750000] hub 3-0:1.0: USB hub found
141[    4.750000] hub 3-0:1.0: 2 ports detected
142[    4.750000] xhci_hcd 0000:01:00.0: xHCI Host Controller
143[    4.760000] xhci_hcd 0000:01:00.0: new USB bus registered, assigned bus number 4
144[    4.770000] hub 4-0:1.0: USB hub found
145[    4.770000] hub 4-0:1.0: 2 ports detected
146[    5.000000] usb 1-1: new high-speed USB device number 2 using ehci-platform
147[    5.270000] init: - preinit -
148[    6.150000] random: procd urandom read with 10 bits of entropy available
149[    7.720000] eth0: link up (1000Mbps/Full duplex)
150[    9.600000] jffs2: notice: (399) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
151[    9.620000] mount_root: switching to jffs2 overlay
152[    9.710000] eth0: link down
153[    9.750000] procd: - early -
154[    9.750000] procd: - watchdog -
155[   10.490000] procd: - ubus -
156[   11.500000] procd: - init -
157[   14.150000] NET: Registered protocol family 10
158[   14.300000] tun: Universal TUN/TAP device driver, 1.6
159[   14.310000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
160[   14.320000] SCSI subsystem initialized
161[   14.330000] ip6_tables: (C) 2000-2006 Netfilter Core Team
162[   14.350000] Loading modules backported from Linux version master-2015-03-09-0-g141f155
163[   14.360000] Backport generated by backports.git backports-20150129-0-gdd4a670
164[   14.390000] cfg80211: Calling CRDA to update world regulatory domain
165[   14.390000] cfg80211: World regulatory domain updated:
166[   14.400000] cfg80211:  DFS Master region: unset
167[   14.400000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
168[   14.410000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
169[   14.420000] cfg80211:   (2457000 KHz - 2482000 KHz @ 20000 KHz, 92000 KHz AUTO), (N/A, 2000 mBm), (N/A)
170[   14.430000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
171[   14.440000] cfg80211:   (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (N/A)
172[   14.450000] cfg80211:   (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s)
173[   14.460000] cfg80211:   (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
174[   14.460000] cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
175[   14.470000] cfg80211:   (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
176[   14.560000] PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
177[   14.570000] ath10k_pci 0000:00:00.0: pci irq legacy interrupts 0 irq_mode 0 reset_mode 0
178[   14.790000] ath10k_pci 0000:00:00.0: Direct firmware load for ath10k/cal-pci-0000:00:00.0.bin failed with error -2
179[   14.800000] ath10k_pci 0000:00:00.0: Falling back to user helper
180[   14.890000] firmware ath10k!cal-pci-0000:00:00.0.bin: firmware_loading_store: map pages failed
181[   16.290000] ath10k_pci 0000:00:00.0: qca988x hw2.0 (0x4100016c, 0x043202ff) fw 10.2.4.45 api 4 htt 2.1 wmi 5 cal otp max_sta 128
182[   16.300000] ath10k_pci 0000:00:00.0: debug 0 debugfs 1 tracing 0 dfs 1 testmode 1
183[   16.410000] ath: EEPROM regdomain: 0x0
184[   16.410000] ath: EEPROM indicates default country code should be used
185[   16.410000] ath: doing EEPROM country->regdmn map search
186[   16.410000] ath: country maps to regdmn code: 0x3a
187[   16.410000] ath: Country alpha2 being used: US
188[   16.410000] ath: Regpair used: 0x3a
189[   16.410000] cfg80211: Calling CRDA for country: US
190[   16.410000] cfg80211: Regulatory domain changed to country: US
191[   16.420000] cfg80211:  DFS Master region: FCC
192[   16.420000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
193[   16.430000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 3000 mBm), (N/A)
194[   16.440000] cfg80211:   (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2300 mBm), (N/A)
195[   16.450000] cfg80211:   (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2300 mBm), (0 s)
196[   16.460000] cfg80211:   (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2300 mBm), (0 s)
197[   16.470000] cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 3000 mBm), (N/A)
198[   16.480000] cfg80211:   (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4000 mBm), (N/A)
199[   16.510000] ip_tables: (C) 2000-2006 Netfilter Core Team
200[   16.520000] nf_conntrack version 0.5.0 (1969 buckets, 7876 max)
201[   16.540000] usb-storage 1-1:1.0: USB Mass Storage device detected
202[   16.550000] scsi host0: usb-storage 1-1:1.0
203[   16.550000] usbcore: registered new interface driver usb-storage
204[   16.570000] xt_time: kernel timezone is -0000
205[   16.590000] PPP generic driver version 2.4.2
206[   16.600000] NET: Registered protocol family 24
207[   16.600000] usbcore: registered new interface driver ums-alauda
208[   16.610000] usbcore: registered new interface driver ums-cypress
209[   16.620000] usbcore: registered new interface driver ums-datafab
210[   16.620000] usbcore: registered new interface driver ums-freecom
211[   16.630000] usbcore: registered new interface driver ums-isd200
212[   16.640000] usbcore: registered new interface driver ums-jumpshot
213[   16.650000] usbcore: registered new interface driver ums-karma
214[   16.650000] usbcore: registered new interface driver ums-sddr09
215[   16.670000] usbcore: registered new interface driver ums-sddr55
216[   16.680000] usbcore: registered new interface driver ums-usbat
217[   16.710000] ath: EEPROM regdomain: 0x0
218[   16.710000] ath: EEPROM indicates default country code should be used
219[   16.710000] ath: doing EEPROM country->regdmn map search
220[   16.710000] ath: country maps to regdmn code: 0x3a
221[   16.710000] ath: Country alpha2 being used: US
222[   16.710000] ath: Regpair used: 0x3a
223[   16.720000] ieee80211 phy1: Selected rate control algorithm 'minstrel_ht'
224[   16.720000] ieee80211 phy1: Atheros AR9550 Rev:0 mem=0xb8100000, irq=47
225[   17.550000] scsi 0:0:0:0: Direct-Access     SanDisk  Cruzer Blade     1.19 PQ: 0 ANSI: 5
226[   17.560000] sd 0:0:0:0: [sda] 15633408 512-byte logical blocks: (8.00 GB/7.45 GiB)
227[   17.570000] sd 0:0:0:0: [sda] Write Protect is off
228[   17.570000] sd 0:0:0:0: [sda] Mode Sense: 43 00 00 00
229[   17.570000] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
230[   17.590000]  sda: sda1
231[   17.600000] sd 0:0:0:0: [sda] Attached SCSI removable disk
232[   24.740000] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
233[   24.760000] device eth0.1 entered promiscuous mode
234[   24.760000] device eth0 entered promiscuous mode
235[   24.790000] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
236[   24.880000] device eth0.2 entered promiscuous mode
237[   25.450000] cfg80211: Calling CRDA for country: CN
238[   25.450000] cfg80211: Regulatory domain changed to country: CN
239[   25.460000] cfg80211:  DFS Master region: FCC
240[   25.460000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
241[   25.470000] cfg80211:   (2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
242[   25.480000] cfg80211:   (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2300 mBm), (N/A)
243[   25.490000] cfg80211:   (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2300 mBm), (0 s)
244[   25.500000] cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 3000 mBm), (N/A)
245[   25.510000] cfg80211:   (57240000 KHz - 59400000 KHz @ 2160000 KHz), (N/A, 2800 mBm), (N/A)
246[   25.510000] cfg80211:   (59400000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4400 mBm), (N/A)
247[   25.520000] cfg80211:   (63720000 KHz - 65880000 KHz @ 2160000 KHz), (N/A, 2800 mBm), (N/A)
248[   25.800000] eth0: link up (1000Mbps/Full duplex)
249[   25.800000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
250[   25.840000] br-lan: port 1(eth0.1) entered forwarding state
251[   25.840000] br-lan: port 1(eth0.1) entered forwarding state
252[   25.850000] br-lan: port 2(eth0.2) entered forwarding state
253[   25.850000] br-lan: port 2(eth0.2) entered forwarding state
254[   25.860000] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
255[   27.800000] Atheros AR8216/AR8236/AR8316 ag71xx-mdio.0:00: Port 2 is up
256[   27.840000] br-lan: port 1(eth0.1) entered forwarding state
257[   27.850000] br-lan: port 2(eth0.2) entered forwarding state
258[   30.360000] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
259[   30.390000] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready
260[   30.400000] device wlan0 entered promiscuous mode
261[   30.430000] device wlan1 entered promiscuous mode
262[   31.560000] br-lan: port 4(wlan1) entered forwarding state
263[   31.570000] br-lan: port 4(wlan1) entered forwarding state
264[   31.570000] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
265[   33.570000] br-lan: port 4(wlan1) entered forwarding state
266[   43.920000] random: nonblocking pool is initialized
267[   46.100000] br-lan: port 3(wlan0) entered forwarding state
268[   46.100000] br-lan: port 3(wlan0) entered forwarding state
269[   46.110000] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
270[   48.100000] br-lan: port 3(wlan0) entered forwarding state
271[  153.860000] Atheros AR8216/AR8236/AR8316 ag71xx-mdio.0:00: Port 5 is up
272[  264.470000] device wlan0 left promiscuous mode
273[  264.480000] br-lan: port 3(wlan0) entered disabled state
274[  268.040000] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
275[  268.070000] device wlan0 entered promiscuous mode
276[  283.770000] br-lan: port 3(wlan0) entered forwarding state
277[  283.770000] br-lan: port 3(wlan0) entered forwarding state
278[  283.780000] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
279[  285.770000] br-lan: port 3(wlan0) entered forwarding state
280[  495.500000] Atheros AR8216/AR8236/AR8316 ag71xx-mdio.0:00: Port 5 is down
281[ 1081.860000] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem
282[ 1081.900000] EXT4-fs (sda1): recovery complete
283[ 1081.910000] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
284[ 6402.190000] device wlan0 left promiscuous mode
285[ 6402.200000] br-lan: port 3(wlan0) entered disabled state
286[ 6405.610000] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
287[ 6405.630000] device wlan0 entered promiscuous mode
288[ 6421.620000] br-lan: port 3(wlan0) entered forwarding state
289[ 6421.620000] br-lan: port 3(wlan0) entered forwarding state
290[ 6421.630000] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
291[ 6423.620000] br-lan: port 3(wlan0) entered forwarding state
292[50811.870000] Atheros AR8216/AR8236/AR8316 ag71xx-mdio.0:00: Port 3 is up
293[50838.000000] Atheros AR8216/AR8236/AR8316 ag71xx-mdio.0:00: Port 3 is down
294[50842.020000] Atheros AR8216/AR8236/AR8316 ag71xx-mdio.0:00: Port 3 is up
295[51117.390000] Atheros AR8216/AR8236/AR8316 ag71xx-mdio.0:00: Port 3 is down
296[654610.190000] Atheros AR8216/AR8236/AR8316 ag71xx-mdio.0:00: Port 2 is down
297[654612.200000] Atheros AR8216/AR8236/AR8316 ag71xx-mdio.0:00: Port 2 is up
298[903770.750000] usb 4-1: new SuperSpeed USB device number 2 using xhci_hcd
299[903770.770000] usb-storage 4-1:1.0: USB Mass Storage device detected
300[903770.780000] scsi host1: usb-storage 4-1:1.0
301[903771.790000] scsi 1:0:0:0: Direct-Access     SanDisk  Ultra Fit        1.00 PQ: 0 ANSI: 6
302[903771.800000] sd 1:0:0:0: [sdb] 60062500 512-byte logical blocks: (30.7 GB/28.6 GiB)
303[903771.810000] sd 1:0:0:0: [sdb] Write Protect is off
304[903771.820000] sd 1:0:0:0: [sdb] Mode Sense: 43 00 00 00
305[903771.820000] sd 1:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
306[903771.840000]  sdb: sdb1
307[903771.850000] sd 1:0:0:0: [sdb] Attached SCSI removable disk
308[904442.060000] xhci_hcd 0000:01:00.0: xHCI host not responding to stop endpoint command.
309[904442.060000] xhci_hcd 0000:01:00.0: Assuming host is dying, halting host.
310[904442.070000] xhci_hcd 0000:01:00.0: HC died; cleaning up
311[904442.080000] usb 4-1: USB disconnect, device number 2
312[904442.100000] sd 1:0:0:0: [sdb]
313[904442.100000] Result: hostbyte=0x01 driverbyte=0x00
314[904442.100000] sd 1:0:0:0: [sdb] CDB:
315[904442.110000] cdb[0]=0x2a: 2a 00 00 00 00 20 00 00 08 00
316[904442.110000] blk_update_request: I/O error, dev sdb, sector 32
317[904442.120000] Buffer I/O error on dev sdb1, logical block 0, lost async page write
318[904442.130000] Buffer I/O error on dev sdb1, logical block 1, lost async page write
319[904442.150000] sd 1:0:0:0: [sdb]
320[904442.150000] Result: hostbyte=0x01 driverbyte=0x00
321[904442.160000] sd 1:0:0:0: [sdb] CDB:
322[904442.160000] cdb[0]=0x2a: 2a 00 00 00 00 38 00 00 f0 00
323[904442.170000] blk_update_request: I/O error, dev sdb, sector 56
324[904442.170000] Buffer I/O error on dev sdb1, logical block 6, lost async page write
325[904442.180000] Buffer I/O error on dev sdb1, logical block 7, lost async page write
326[904442.190000] Buffer I/O error on dev sdb1, logical block 8, lost async page write
327[904442.200000] Buffer I/O error on dev sdb1, logical block 9, lost async page write
328[904442.200000] Buffer I/O error on dev sdb1, logical block 10, lost async page write
329[904442.210000] Buffer I/O error on dev sdb1, logical block 11, lost async page write
330[904442.220000] Buffer I/O error on dev sdb1, logical block 12, lost async page write
331[904442.230000] Buffer I/O error on dev sdb1, logical block 13, lost async page write
332[904442.360000] ------------[ cut here ]------------
333[904442.370000] WARNING: CPU: 0 PID: 26080 at fs/fs-writeback.c:1215 __mark_inode_dirty+0x114/0x1ac()
334[904442.380000] bdi-block not registered
335[904442.380000] Modules linked in: pppoe ppp_async iptable_nat ath9k ums_usbat ums_sddr55 ums_sddr09 ums_karma ums_jumpshot ums_isd200 ums_freecom ums_datafab ums_cypress ums_alauda pppox ppp_generic nf_nat_ipv4 nf_conntrack_ipv6 nf_conntrack_ipv4 ipt_REJECT ipt_MASQUERADE ath9k_common xt_time xt_tcpudp xt_state xt_nat xt_multiport xt_mark xt_mac xt_limit xt_id xt_conntrack xt_comment xt_TCPMSS xt_REDIRECT xt_LOG xt_CT usb_storage slhc nf_reject_ipv4 nf_nat_masquerade_ipv4 nf_nat_ftp nf_nat nf_log_ipv4 nf_defrag_ipv6 nf_defrag_ipv4 nf_conntrack_rtcache nf_conntrack_ftp nf_conntrack iptable_raw iptable_mangle iptable_filter ip_tables crc_ccitt ath9k_hw ath10k_pci ath10k_core ath mac80211 cfg80211 compat ledtrig_usbdev ip6t_REJECT nf_reject_ipv6 nf_log_ipv6 nf_log_common ip6table_raw ip6table_mangle ip6table_filter ip6_tables x_tables sd_mod scsi_mod tun ext4 jbd2 mbcache crc16 ipv6 arc4 crypto_blkcipher crypto_hash xhci_plat_hcd xhci_pci xhci_hcd ehci_platform ehci_hcd gpio_button_hotplug usbcore nls_base usb_common
336[904442.470000] CPU: 0 PID: 26080 Comm: mkfs.ext4 Not tainted 3.18.23 #1
337[904442.480000] Stack : 00000000 00000000 00000000 00000000 803d4292 00000038 00000000 8011f154
338[904442.480000]           00000001 ffffffff 8031f208 80376ba3 000065e0 803d34d0 878f4248 ffffffff
339[904442.480000]           00000000 00001000 00000001 800a364c 00000003 8008043c 000004bf ffffffff
340[904442.480000]           80322800 83587c04 00000000 00000000 00000000 00000000 00000000 00000000
341[904442.480000]           00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
342[904442.480000]           ...
343[904442.520000] Call Trace:
344[904442.520000] [<80071060>] show_stack+0x50/0x84
345[904442.520000] [<80080544>] warn_slowpath_common+0x84/0xb4
346[904442.530000] [<800805a0>] warn_slowpath_fmt+0x2c/0x38
347[904442.530000] [<8011f154>] __mark_inode_dirty+0x114/0x1ac
348[904442.540000] [<8012684c>] __block_commit_write.isra.28+0xb0/0x120
349[904442.550000] [<8012692c>] block_write_end+0x70/0x8c
350[904442.550000] [<8012a52c>] blkdev_write_end+0x34/0x60
351[904442.560000] [<800c82fc>] generic_perform_write+0x124/0x1f4
352[904442.560000] [<800ca058>] __generic_file_write_iter+0x360/0x3f4
353[904442.570000] [<8012a6a4>] blkdev_write_iter+0x34/0xec
354[904442.570000] [<800fb82c>] new_sync_write+0x88/0xc0
355[904442.580000] [<800fc15c>] vfs_write+0xb8/0x1bc
356[904442.580000] [<800fc8cc>] SyS_pwrite64+0x6c/0xb4
357[904442.590000] [<80062b5c>] handle_sys+0x11c/0x140
358[904442.590000]
359[904442.590000] ---[ end trace 1ba70ff86f69ef12 ]---