Ticket #14436: boot openwrt.txt

File boot openwrt.txt, 26.6 KB (added by rpc@…, 4 years ago)

boot log openwrt on TD8970

Line 
1
2ROM VER: 1.1.4
3CFG 05
4
5ROM VER: 1.1.4
6CFG 05
7
8DDR autotuning Rev 0.3ff
9DDR size from 0xa0000000 - 0xa3ffffff
10DDR check ok... start booting...
11
12
13
14U-Boot 2010.06-LANTIQ-v-2.0.40-svn4469 (Aug 28 2013 - 09:28:56)
15
16CLOCK CPU 500M RAM 250M
17DRAM:  64 MiB
18Using default environment
19
20In:    serial
21Out:   serial
22Err:   serial
23Net:   Internal phy(GE) firmware version: 0x8434
24vr9 Switch8192 KiB W25Q64 at 0:3 is now current device
25
26
27Type "run flash_nfs" to mount root filesystem over NFS
28
29Hit any key to stop autoboot:  1 0
308192 KiB W25Q64 at 0:3 is now current device
318192 KiB W25Q64 at 0:3 is now current device
32        Uncompressing ...
33Starting kernel ...
34
35[    0.000000] Linux version 3.10.17 (rcichosz@ubuntu) (gcc version 4.6.4 (OpenWrt/Linaro GCC 4.6-2013.05 r38632) ) #1 Fri Nov 1 00:23:50 CET 2013
36
37[    0.000000] SoC: VR9 rev 1.2
38
39[    0.000000] bootconsole [early0] enabled
40
41[    0.000000] CPU revision is: 00019556 (MIPS 34Kc)
42
43[    0.000000] MIPS: machine is TDW8970 - TP-LINK TD-W8970
44
45[    0.000000] Determined physical RAM map:
46
47[    0.000000]  memory: 04000000 @ 00000000 (usable)
48
49[    0.000000] Initrd not found or empty - disabling initrd
50
51[    0.000000] Zone ranges:
52
53[    0.000000]   Normal   [mem 0x00000000-0x03ffffff]
54
55[    0.000000] Movable zone start for each node
56
57[    0.000000] Early memory node ranges
58
59[    0.000000]   node   0: [mem 0x00000000-0x03ffffff]
60
61[    0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
62
63[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
64
65[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
66
67[    0.000000] Kernel command line: console=ttyLTQ0,115200 init=/etc/preinit
68
69[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
70
71[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
72
73[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
74
75[    0.000000] Writing ErrCtl register=0000c0b0
76
77[    0.000000] Readback ErrCtl register=0000c0b0
78
79[    0.000000] Memory: 60868k/65536k available (2739k kernel code, 4668k reserved, 887k data, 204k init, 0k highmem)
80
81[    0.000000] NR_IRQS:256
82
83[    0.000000] CPU Clock: 500MHz
84
85[    0.000000] Calibrating delay loop... 332.54 BogoMIPS (lpj=665088)
86
87[    0.032000] pid_max: default: 32768 minimum: 301
88
89[    0.036000] Mount-cache hash table entries: 512
90
91[    0.040000] pinctrl core: initialized pinctrl subsystem
92
93[    0.044000] NET: Registered protocol family 16
94
95[    0.056000] pinctrl-xway 1e100b10.pinmux: Init done
96
97[    0.060000] dma-xway 1e104100.dma: Init done - hw rev: 7, ports: 7, channels: 28
98
99[    0.068000] dcdc-xrx200 1f106a00.dcdc: Core Voltage : 1016 mV
100
101[    0.072000] arch/mips/pci/ifxmips_pcie_vr9.h:pcie_device_rst_assert[185]
102
103[    0.184000] arch/mips/pci/ifxmips_pcie_vr9.h:pcie_device_rst_deassert[193]
104
105[    0.188000] ath9k,eeprom ath9k_eep.8: failed to find mtd device
106
107[    0.200000] bio: create slab <bio-0> at 0
108
109[    0.204000] usbcore: registered new interface driver usbfs
110
111[    0.208000] usbcore: registered new interface driver hub
112
113[    0.212000] usbcore: registered new device driver usb
114
115[    0.216000] PCI host bridge to bus 0000:00
116
117[    0.220000] pci_bus 0000:00: root bus resource [mem 0x1c000000-0x1cffffff]
118
119[    0.224000] pci_bus 0000:00: root bus resource [io  0x1d800000-0x1d8fffff]
120
121[    0.228000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
122
123[    0.232000] ifx_pcie_rc_class_early_fixup: fixed pcie host bridge to pci-pci bridge
124
125[    0.244000] pci 0000:00:00.0: BAR 8: assigned [mem 0x1c000000-0x1c0fffff]
126
127[    0.248000] pci 0000:00:00.0: BAR 9: assigned [mem 0x1c100000-0x1c1fffff pref]
128
129[    0.252000] pci 0000:01:00.0: BAR 0: assigned [mem 0x1c000000-0x1c01ffff 64bit]
130
131[    0.256000] pci 0000:01:00.0: BAR 6: assigned [mem 0x1c100000-0x1c10ffff pref]
132
133[    0.260000] pci 0000:00:00.0: PCI bridge to [bus 01]
134
135[    0.264000] pci 0000:00:00.0:   bridge window [mem 0x1c000000-0x1c0fffff]
136
137[    0.268000] pci 0000:00:00.0:   bridge window [mem 0x1c100000-0x1c1fffff pref]
138
139[    0.272000] PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
140
141[    0.276000] ifx_pcie_bios_map_irq port 0 dev 0000:00:00.0 slot 0 pin 1
142
143[    0.280000] ifx_pcie_bios_map_irq dev 0000:00:00.0 irq 144 assigned
144
145[    0.284000] ifx_pcie_bios_map_irq port 0 dev 0000:01:00.0 slot 0 pin 1
146
147[    0.288000] ifx_pcie_bios_map_irq dev 0000:01:00.0 irq 144 assigned
148
149[    0.292000] Switching to clocksource MIPS
150
151[    0.300000] NET: Registered protocol family 2
152
153[    0.304000] TCP established hash table entries: 512 (order: 0, 4096 bytes)
154
155[    0.312000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)
156
157[    0.316000] TCP: Hash tables configured (established 512 bind 512)
158
159[    0.324000] TCP: reno registered
160
161[    0.328000] UDP hash table entries: 256 (order: 0, 4096 bytes)
162
163[    0.332000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
164
165[    0.340000] NET: Registered protocol family 1
166
167[    0.344000] gptu: totally 6 16-bit timers/counters
168
169[    0.348000] gptu: misc_register on minor 63
170
171[    0.352000] gptu: succeeded to request irq 126
172
173[    0.356000] gptu: succeeded to request irq 127
174
175[    0.360000] gptu: succeeded to request irq 128
176
177[    0.368000] gptu: succeeded to request irq 129
178
179[    0.372000] gptu: succeeded to request irq 130
180
181[    0.376000] gptu: succeeded to request irq 131
182
183[    0.380000] phy-xrx200 gphy-xrx200.5: requesting lantiq/vr9_phy11g_a2x.bin
184
185[    0.388000] phy-xrx200 gphy-xrx200.5: booting GPHY0 firmware at 38C0000
186
187[    0.396000] phy-xrx200 gphy-xrx200.5: booting GPHY1 firmware at 38C0000
188
189[    0.504000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
190
191[    0.512000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
192
193[    0.520000] msgmni has been set to 118
194
195[    0.524000] io scheduler noop registered
196
197[    0.528000] io scheduler deadline registered (default)
198
199[    0.536000] 1e100c00.serial: ttyLTQ0 at MMIO 0x1e100c00 (irq = 112) is a lantiq,asc
200
201[    0.544000] console [ttyLTQ0] enabled, bootconsole disabled
202[    0.544000] console [ttyLTQ0] enabled, bootconsole disabled
203
204[    0.560000] spi_gpio spi.7: master is unqueued, this is deprecated
205[    0.564000] m25p80 spi32766.0: found s25fl064k, expected en25q64
206[    0.568000] m25p80 spi32766.0: s25fl064k (8192 Kbytes)
207[    0.576000] 4 ofpart partitions found on MTD device spi32766.0
208[    0.580000] Creating 4 MTD partitions on "spi32766.0":
209[    0.584000] 0x000000000000-0x000000020000 : "u-boot"
210[    0.592000] 0x000000020000-0x0000007c0000 : "firmware"
211[    0.600000] 0x0000001589b0-0x0000007c0000 : "rootfs"
212[    0.600000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
213[    0.616000] mtd: partition "rootfs" set to be root filesystem
214[    0.620000] mtd: partition "rootfs_data" created automatically, ofs=0x640000, len=0x180000
215[    0.628000] 0x000000640000-0x0000007c0000 : "rootfs_data"
216[    1.628000] 0x0000007c0000-0x0000007d0000 : "config"
217[    1.636000] 0x0000007d0000-0x000000800000 : "boardconfig"
218[    1.748000] libphy: lantiq,xrx200-mdio: probed
219[    1.752000] net-xrx200: invalid MAC, using random
220[    1.756000] eth0: attached PHY [Lantiq XWAY PEF7071] (phy_addr=0:00, irq=-1)
221[    1.764000] eth0: attached PHY [Lantiq XWAY PEF7071] (phy_addr=0:05, irq=-1)
222[    1.772000] eth0: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.4] (phy_addr=0:11, irq=-1)
223[    1.780000] eth0: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.4] (phy_addr=0:13, irq=-1)
224[    1.788000] wdt 1f8803f0.watchdog: Init done
225[    1.792000] leds-gpio gpio-leds.10: pins are not configured from the driver
226[    1.800000] TCP: cubic registered
227[    1.804000] NET: Registered protocol family 17
228[    1.808000] Bridge firewalling registered
229[    1.812000] 8021q: 802.1Q VLAN Support v1.8
230[    1.896000] ath9k,eeprom ath9k_eep.8: using random mac
231[    1.900000] ath9k,eeprom ath9k_eep.8: pci slot: 0
232[    1.904000] ath9k,eeprom ath9k_eep.8: loaded ath9k eeprom
233[    2.020000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
234[    2.028000] Freeing unused kernel memory: 204K (8038d000 - 803c0000)
235Console is alive
236procd: Console is alive
237- watchdog -
238procd: - watchdog -
239
240[   44.340000] SCSI subsystem initialized
241[   44.348000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
242[   44.356000] ehci-platform: EHCI generic platform driver
243[   44.360000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
244[   44.368000] uhci_hcd: USB Universal Host Controller Interface driver
245[   44.380000] IFXUSB: ifxusb_hcd: version 3.2 B110801
246[   44.384000] Chip Version :000c BurstSize=4
247[   44.988000] IFXUSB: USB core #0 soft-reset
248[   45.288000] IFXUSB: USB core #0 soft-reset
249[   45.292000] ifxusb_hcd ifxusb_hcd: IFX USB Controller
250[   45.296000] ifxusb_hcd ifxusb_hcd: new USB bus registered, assigned bus number 1
251[   45.304000] ifxusb_hcd ifxusb_hcd: irq 62, io mem 0xbe101000
252[   45.312000] IFXUSB: Init: Power Port (0)
253[   45.316000] hub 1-0:1.0: USB hub found
254[   45.316000] hub 1-0:1.0: 1 port detected
255
256ROM VER: 1.1.4
257CFG 05
258
259DDR autotuning Rev 0.3ff
260DDR size from 0xa0000000 - 0xa3ffffff
261DDR check ok... start booting...
262
263
264
265U-Boot 2010.06-LANTIQ-v-2.0.40-svn4469 (Aug 28 2013 - 09:28:56)
266
267CLOCK CPU 500M RAM 250M
268DRAM:  64 MiB
269Using default environment
270
271In:    serial
272Out:   serial
273Err:   serial
274Net:   Internal phy(GE) firmware version: 0x8434
275vr9 Switch8192 KiB W25Q64 at 0:3 is now current device
276
277
278Type "run flash_nfs" to mount root filesystem over NFS
279
280Hit any key to stop autoboot:  1 0
2818192 KiB W25Q64 at 0:3 is now current device
2828192 KiB W25Q64 at 0:3 is now current device
283        Uncompressing ...
284Starting kernel ...
285
286[    0.000000] Linux version 3.10.17 (rcichosz@ubuntu) (gcc version 4.6.4 (OpenWrt/Linaro GCC 4.6-2013.05 r38632) ) #1 Fri Nov 1 00:23:50 CET 2013
287
288[    0.000000] SoC: VR9 rev 1.2
289
290[    0.000000] bootconsole [early0] enabled
291
292[    0.000000] CPU revision is: 00019556 (MIPS 34Kc)
293
294[    0.000000] MIPS: machine is TDW8970 - TP-LINK TD-W8970
295
296[    0.000000] Determined physical RAM map:
297
298[    0.000000]  memory: 04000000 @ 00000000 (usable)
299
300[    0.000000] Initrd not found or empty - disabling initrd
301
302[    0.000000] Zone ranges:
303
304[    0.000000]   Normal   [mem 0x00000000-0x03ffffff]
305
306[    0.000000] Movable zone start for each node
307
308[    0.000000] Early memory node ranges
309
310[    0.000000]   node   0: [mem 0x00000000-0x03ffffff]
311
312[    0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
313
314[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
315
316[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
317
318[    0.000000] Kernel command line: console=ttyLTQ0,115200 init=/etc/preinit
319
320[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
321
322[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
323
324[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
325
326[    0.000000] Writing ErrCtl register=0000c0b0
327
328[    0.000000] Readback ErrCtl register=0000c0b0
329
330[    0.000000] Memory: 60868k/65536k available (2739k kernel code, 4668k reserved, 887k data, 204k init, 0k highmem)
331
332[    0.000000] NR_IRQS:256
333
334[    0.000000] CPU Clock: 500MHz
335
336[    0.000000] Calibrating delay loop... 332.54 BogoMIPS (lpj=665088)
337
338[    0.032000] pid_max: default: 32768 minimum: 301
339
340[    0.036000] Mount-cache hash table entries: 512
341
342[    0.040000] pinctrl core: initialized pinctrl subsystem
343
344[    0.044000] NET: Registered protocol family 16
345
346[    0.056000] pinctrl-xway 1e100b10.pinmux: Init done
347
348[    0.060000] dma-xway 1e104100.dma: Init done - hw rev: 7, ports: 7, channels: 28
349
350[    0.068000] dcdc-xrx200 1f106a00.dcdc: Core Voltage : 1016 mV
351
352[    0.072000] arch/mips/pci/ifxmips_pcie_vr9.h:pcie_device_rst_assert[185]
353
354[    0.184000] arch/mips/pci/ifxmips_pcie_vr9.h:pcie_device_rst_deassert[193]
355
356[    0.188000] ath9k,eeprom ath9k_eep.8: failed to find mtd device
357
358[    0.200000] bio: create slab <bio-0> at 0
359
360[    0.204000] usbcore: registered new interface driver usbfs
361
362[    0.208000] usbcore: registered new interface driver hub
363
364[    0.212000] usbcore: registered new device driver usb
365
366[    0.216000] PCI host bridge to bus 0000:00
367
368[    0.220000] pci_bus 0000:00: root bus resource [mem 0x1c000000-0x1cffffff]
369
370[    0.224000] pci_bus 0000:00: root bus resource [io  0x1d800000-0x1d8fffff]
371
372[    0.228000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
373
374[    0.232000] ifx_pcie_rc_class_early_fixup: fixed pcie host bridge to pci-pci bridge
375
376[    0.244000] pci 0000:00:00.0: BAR 8: assigned [mem 0x1c000000-0x1c0fffff]
377
378[    0.248000] pci 0000:00:00.0: BAR 9: assigned [mem 0x1c100000-0x1c1fffff pref]
379
380[    0.252000] pci 0000:01:00.0: BAR 0: assigned [mem 0x1c000000-0x1c01ffff 64bit]
381
382[    0.256000] pci 0000:01:00.0: BAR 6: assigned [mem 0x1c100000-0x1c10ffff pref]
383
384[    0.260000] pci 0000:00:00.0: PCI bridge to [bus 01]
385
386[    0.264000] pci 0000:00:00.0:   bridge window [mem 0x1c000000-0x1c0fffff]
387
388[    0.268000] pci 0000:00:00.0:   bridge window [mem 0x1c100000-0x1c1fffff pref]
389
390[    0.272000] PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
391
392[    0.276000] ifx_pcie_bios_map_irq port 0 dev 0000:00:00.0 slot 0 pin 1
393
394[    0.280000] ifx_pcie_bios_map_irq dev 0000:00:00.0 irq 144 assigned
395
396[    0.284000] ifx_pcie_bios_map_irq port 0 dev 0000:01:00.0 slot 0 pin 1
397
398[    0.288000] ifx_pcie_bios_map_irq dev 0000:01:00.0 irq 144 assigned
399
400[    0.292000] Switching to clocksource MIPS
401
402[    0.300000] NET: Registered protocol family 2
403
404[    0.304000] TCP established hash table entries: 512 (order: 0, 4096 bytes)
405
406[    0.312000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)
407
408[    0.316000] TCP: Hash tables configured (established 512 bind 512)
409
410[    0.324000] TCP: reno registered
411
412[    0.328000] UDP hash table entries: 256 (order: 0, 4096 bytes)
413
414[    0.332000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
415
416[    0.340000] NET: Registered protocol family 1
417
418[    0.344000] gptu: totally 6 16-bit timers/counters
419
420[    0.348000] gptu: misc_register on minor 63
421
422[    0.352000] gptu: succeeded to request irq 126
423
424[    0.356000] gptu: succeeded to request irq 127
425
426[    0.360000] gptu: succeeded to request irq 128
427
428[    0.368000] gptu: succeeded to request irq 129
429
430[    0.372000] gptu: succeeded to request irq 130
431
432[    0.376000] gptu: succeeded to request irq 131
433
434[    0.380000] phy-xrx200 gphy-xrx200.5: requesting lantiq/vr9_phy11g_a2x.bin
435
436[    0.388000] phy-xrx200 gphy-xrx200.5: booting GPHY0 firmware at 38C0000
437
438[    0.396000] phy-xrx200 gphy-xrx200.5: booting GPHY1 firmware at 38C0000
439
440[    0.504000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
441
442[    0.512000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
443
444[    0.520000] msgmni has been set to 118
445
446[    0.524000] io scheduler noop registered
447
448[    0.528000] io scheduler deadline registered (default)
449
450[    0.536000] 1e100c00.serial: ttyLTQ0 at MMIO 0x1e100c00 (irq = 112) is a lantiq,asc
451
452[    0.544000] console [ttyLTQ0] enabled, bootconsole disabled
453[    0.544000] console [ttyLTQ0] enabled, bootconsole disabled
454
455[    0.560000] spi_gpio spi.7: master is unqueued, this is deprecated
456[    0.564000] m25p80 spi32766.0: found s25fl064k, expected en25q64
457[    0.568000] m25p80 spi32766.0: s25fl064k (8192 Kbytes)
458[    0.576000] 4 ofpart partitions found on MTD device spi32766.0
459[    0.580000] Creating 4 MTD partitions on "spi32766.0":
460[    0.584000] 0x000000000000-0x000000020000 : "u-boot"
461[    0.592000] 0x000000020000-0x0000007c0000 : "firmware"
462[    0.600000] 0x0000001589b0-0x0000007c0000 : "rootfs"
463[    0.600000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
464[    0.616000] mtd: partition "rootfs" set to be root filesystem
465[    0.620000] mtd: partition "rootfs_data" created automatically, ofs=0x640000, len=0x180000
466[    0.628000] 0x000000640000-0x0000007c0000 : "rootfs_data"
467[    1.628000] 0x0000007c0000-0x0000007d0000 : "config"
468[    1.636000] 0x0000007d0000-0x000000800000 : "boardconfig"
469[    1.748000] libphy: lantiq,xrx200-mdio: probed
470[    1.756000] net-xrx200: invalid MAC, using random
471[    1.760000] eth0: attached PHY [Lantiq XWAY PEF7071] (phy_addr=0:00, irq=-1)
472[    1.764000] eth0: attached PHY [Lantiq XWAY PEF7071] (phy_addr=0:05, irq=-1)
473[    1.772000] eth0: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.4] (phy_addr=0:11, irq=-1)
474[    1.780000] eth0: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.4] (phy_addr=0:13, irq=-1)
475[    1.788000] wdt 1f8803f0.watchdog: Init done
476[    1.792000] leds-gpio gpio-leds.10: pins are not configured from the driver
477[    1.800000] TCP: cubic registered
478[    1.804000] NET: Registered protocol family 17
479[    1.808000] Bridge firewalling registered
480[    1.812000] 8021q: 802.1Q VLAN Support v1.8
481[    1.896000] ath9k,eeprom ath9k_eep.8: using random mac
482[    1.900000] ath9k,eeprom ath9k_eep.8: pci slot: 0
483[    1.908000] ath9k,eeprom ath9k_eep.8: loaded ath9k eeprom
484[    2.020000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
485[    2.028000] Freeing unused kernel memory: 204K (8038d000 - 803c0000)
486Console is alive
487procd: Console is alive
488- watchdog -
489procd: - watchdog -
490[   44.340000] SCSI subsystem initialized
491[   44.348000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
492[   44.356000] ehci-platform: EHCI generic platform driver
493[   44.360000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
494[   44.368000] uhci_hcd: USB Universal Host Controller Interface driver
495[   44.380000] IFXUSB: ifxusb_hcd: version 3.2 B110801
496[   44.384000] Chip Version :000c BurstSize=4
497[   44.888000] IFXUSB: USB core #0 soft-reset
498[   45.188000] IFXUSB: USB core #0 soft-reset
499[   45.192000] ifxusb_hcd ifxusb_hcd: IFX USB Controller
500[   45.196000] ifxusb_hcd ifxusb_hcd: new USB bus registered, assigned bus number 1
501[   45.204000] ifxusb_hcd ifxusb_hcd: irq 62, io mem 0xbe101000
502[   45.212000] IFXUSB: Init: Power Port (0)
503[   45.216000] hub 1-0:1.0: USB hub found
504[   45.216000] hub 1-0:1.0: 1 port detected
505[   45.724000] IFXUSB: USB core #1 soft-reset
506[   46.024000] IFXUSB: USB core #1 soft-reset
507[   46.028000] ifxusb_hcd ifxusb_hcd: IFX USB Controller
508[   46.032000] ifxusb_hcd ifxusb_hcd: new USB bus registered, assigned bus number 2
509[   46.040000] ifxusb_hcd ifxusb_hcd: irq 91, io mem 0xbe106000
510[   46.048000] IFXUSB: Init: Power Port (0)
511[   46.052000] hub 2-0:1.0: USB hub found
512[   46.052000] hub 2-0:1.0: 1 port detected
513[   46.060000] ifxusb_hcd ifxusb_hcd: requested GPIO 233
514[   46.068000] usbcore: registered new interface driver usb-storage
515kmod: ran 20 iterations
516- preinit -
517procd: - preinit -
518Press the [f] key and hit [enter] to enter failsafe mode
519kmod: ran 1 iterations
520mount_root: jffs2 is not ready - marker found
521- early -
522procd: - early -
523- watchdog -
524procd: - watchdog -
525- init -
526procd: - init -
527Please press Enter to activate this console.
528[   55.688000] IFXOS, Version 1.5.14 (c) Copyright 2009, Lantiq Deutschland GmbH
529
530
531[   55.712000] NET: Registered protocol family 10
532[   55.724000] NET: Registered protocol family 8
533[   55.728000] NET: Registered protocol family 20
534[   55.744000] gre: GRE over IPv4 demultiplexor driver
535[   55.756000] ip_gre: GRE over IPv4 tunneling driver
536[   55.768000] ip6_gre: GRE over IPv6 tunneling driver
537[   55.784000] PPP generic driver version 2.4.2
538[   55.812000] nf_conntrack version 0.5.0 (954 buckets, 3816 max)
539[   55.840000] ip6_tables: (C) 2000-2006 Netfilter Core Team
540[   55.884000] MEI CPE Driver, Version 1.2.0
541
542
543[   55.884000] (c) Copyright 2009, Infineon Technologies AG
544[   55.884000]
545### MEI CPE - MEI CPE - MEI CPE - MEI CPE ###
546
547
548
549Lantiq CPE API Driver version: DSL CPE API V4.11.4
550[   55.940000]
551[   55.940000] Predefined debug level: 2
552[   55.964000] usbcore: registered new interface driver i2c-tiny-usb
553[   55.992000] fuse init (API version 7.22)
554[   56.012000] Loading modules backported from Linux version master-2013-06-27-0-gdcfa6d5
555[   56.020000] Backport generated by backports.git backports-20130617-4-ge3220f5
556[   56.064000] Ebtables v2.0 registered
557[   56.072000] ip_tables: (C) 2000-2006 Netfilter Core Team
558[   56.092000] ATM1.0.26    ATM (A1) firmware version 0.24
559[   56.096000] ifxmips_atm: ATM init succeed
560[   56.116000] Infineon Technologies DEU driver version 2.0.0
561[   56.124000] IFX DEU DES initialized (multiblock).
562[   56.132000] IFX DEU AES initialized (multiblock).
563[   56.144000] IFX DEU ARC4 initialized (multiblock).
564[   56.144000] IFX DEU SHA1 initialized.
565[   56.148000] IFX DEU MD5 initialized.
566[   56.156000] IFX DEU SHA1_HMAC initialized.
567[   56.160000] IFX DEU MD5_HMAC initialized.
568[   56.184000] nf_conntrack_rtsp v0.6.21 loading
569[   56.224000] nf_nat_rtsp v0.6.21 loading
570[   56.260000] NET: Registered protocol family 24
571[   56.276000] usbcore: registered new interface driver usbserial
572[   56.288000] usbcore: registered new interface driver usbserial_generic
573[   56.296000] usbserial: USB Serial support registered for generic
574[   56.348000] xt_time: kernel timezone is -0000
575[   56.424000] cfg80211: Calling CRDA to update world regulatory domain
576[   56.428000] cfg80211: World regulatory domain updated:
577[   56.432000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
578[   56.440000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
579[   56.448000] cfg80211:   (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
580[   56.456000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
581[   56.464000] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
582[   56.472000] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
583[   56.480000] usbcore: registered new interface driver ch341
584[   56.496000] usbserial: USB Serial support registered for ch341-uart
585[   56.504000] usbcore: registered new interface driver cp210x
586[   56.512000] usbserial: USB Serial support registered for cp210x
587[   56.528000] usbcore: registered new interface driver ftdi_sio
588[   56.532000] usbserial: USB Serial support registered for FTDI USB Serial Device
589[   56.616000] usbcore: registered new interface driver oti6858
590[   56.620000] usbserial: USB Serial support registered for oti6858
591[   56.628000] usbcore: registered new interface driver pl2303
592[   56.632000] usbserial: USB Serial support registered for pl2303
593[   56.672000] usbcore: registered new interface driver rt2800usb
594[   56.688000] PCI: Enabling device 0000:01:00.0 (0000 -> 0002)
595[   56.708000] cfg80211: Calling CRDA for country: US
596[   56.712000] cfg80211: Regulatory domain changed to country: US
597[   56.716000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
598[   56.728000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
599[   56.732000] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)
600[   56.740000] cfg80211:   (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
601[   56.748000] cfg80211:   (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
602[   56.756000] cfg80211:   (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
603[   56.764000] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)
604[   56.772000] ieee80211 phy0: Atheros AR9300 Rev:3 mem=0xbc000000, irq=144
605[   67.508000] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
606[   67.524000] device eth0 entered promiscuous mode
607[   67.532000] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
608^[[B
609
610
611BusyBox v1.19.4 (2013-11-01 00:16:30 CET) built-in shell (ash)
612Enter 'help' for a list of built-in commands.
613
614  _______                     ________        __
615 |       |.-----.-----.-----.|  |  |  |.----.|  |_
616 |   -   ||  _  |  -__|     ||  |  |  ||   _||   _|
617 |_______||   __|_____|__|__||________||__|  |____|
618          |__| W I R E L E S S   F R E E D O M
619 -----------------------------------------------------
620 BARRIER BREAKER (Bleeding Edge, r38632)
621 -----------------------------------------------------
622  * 1/2 oz Galliano         Pour all ingredients into
623  * 4 oz cold Coffee        an irish coffee mug filled
624  * 1 1/2 oz Dark Rum       with crushed ice. Stir.
625  * 2 tsp. Creme de Cacao
626 -----------------------------------------------------
627 
628 root@OpenWrt:/etc/config# ifconfig
629br-lan    Link encap:Ethernet  HWaddr 92:6B:8C:EA:05:D0 
630          inet addr:192.168.1.1  Bcast:192.168.1.255  Mask:255.255.255.0
631          inet6 addr: fe80::906b:8cff:feea:5d0/64 Scope:Link
632          inet6 addr: fd12:4068:6248::1/60 Scope:Global
633          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
634          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
635          TX packets:6 errors:0 dropped:0 overruns:0 carrier:0
636          collisions:0 txqueuelen:0
637          RX bytes:0 (0.0 B)  TX bytes:780 (780.0 B)
638
639eth0      Link encap:Ethernet  HWaddr 92:6B:8C:EA:05:D0 
640          UP BROADCAST MULTICAST  MTU:1500  Metric:1
641          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
642          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
643          collisions:0 txqueuelen:1000
644          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)
645
646lo        Link encap:Local Loopback 
647          inet addr:127.0.0.1  Mask:255.0.0.0
648          inet6 addr: ::1/128 Scope:Host
649          UP LOOPBACK RUNNING  MTU:65536  Metric:1
650          RX packets:5232 errors:0 dropped:0 overruns:0 frame:0
651          TX packets:5232 errors:0 dropped:0 overruns:0 carrier:0
652          collisions:0 txqueuelen:0
653          RX bytes:355776 (347.4 KiB)  TX bytes:355776 (347.4 KiB)
654
655nas0      Link encap:Ethernet  HWaddr 00:00:01:00:00:00 
656          inet6 addr: fe80::200:1ff:fe00:0/64 Scope:Link
657          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
658          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
659          TX packets:276 errors:276 dropped:0 overruns:276 carrier:0
660          collisions:0 txqueuelen:1000
661          RX bytes:0 (0.0 B)  TX bytes:20884 (20.3 KiB)
662
663wlan0     Link encap:Ethernet  HWaddr 16:C6:80:FD:10:54 
664          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
665          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
666          TX packets:9 errors:0 dropped:0 overruns:0 carrier:0
667          collisions:0 txqueuelen:1000
668          RX bytes:0 (0.0 B)  TX bytes:1260 (1.2 KiB)
669