Ticket #14236: dmesg.txt

File dmesg.txt, 10.2 KB (added by Sabrewarrior, 4 years ago)

dmesg

Line 
1[    0.000000] Linux version 3.10.12 (openwrt@huchra) (gcc version 4.6.4 (OpenWrt/Linaro GCC 4.6-2013.05 r38221) ) #1 Fri Sep 27 02:16:52 PDT 2013
2[    0.000000] CPU revision is: 00019749 (MIPS 74Kc)
3[    0.000000] bcm47xx: using bcma bus
4[    0.000000] bcma: bus0: Found chip with id 0xD144, rev 0x01 and package 0x08
5[    0.000000] bcma: bus0: Core 0 found: ChipCommon (manuf 0x4BF, id 0x800, rev 0x27, class 0x0)
6[    0.000000] bcma: bus0: Core 3 found: MIPS 74K (manuf 0x4A7, id 0x82C, rev 0x05, class 0x0)
7[    0.000000] bcma: bus0: Found rev 9 PMU (capabilities 0x28982A09)
8[    0.000000] bcma: bus0: Found serial flash
9[    0.000000] bcma: bus0: Found M25P64 serial flash (size: 8192KiB, blocksize: 0x10000, blocks: 128)
10[    0.000000] bcma: bus0: Early bus registered
11[    0.000000] Determined physical RAM map:
12[    0.000000]  memory: 02000000 @ 00000000 (usable)
13[    0.000000] Initrd not found or empty - disabling initrd
14[    0.000000] Zone ranges:
15[    0.000000]   Normal   [mem 0x00000000-0x01ffffff]
16[    0.000000] Movable zone start for each node
17[    0.000000] Early memory node ranges
18[    0.000000]   node   0: [mem 0x00000000-0x01ffffff]
19[    0.000000] On node 0 totalpages: 8192
20[    0.000000] free_area_init_node: node 0, pgdat 802f6b80, node_mem_map 81000000
21[    0.000000]   Normal zone: 64 pages used for memmap
22[    0.000000]   Normal zone: 0 pages reserved
23[    0.000000]   Normal zone: 8192 pages, LIFO batch:0
24[    0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
25[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
26[    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
27[    0.000000] pcpu-alloc: [0] 0
28[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 8128
29[    0.000000] Kernel command line:  noinitrd console=ttyS0,115200
30[    0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
31[    0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
32[    0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
33[    0.000000] Writing ErrCtl register=00000000
34[    0.000000] Readback ErrCtl register=00000000
35[    0.000000] Memory: 28872k/32768k available (2529k kernel code, 3896k reserved, 582k data, 212k init, 0k highmem)
36[    0.000000] NR_IRQS:128
37[    0.032000] Calibrating delay loop... 149.50 BogoMIPS (lpj=299008)
38[    0.032000] pid_max: default: 32768 minimum: 301
39[    0.032000] Mount-cache hash table entries: 512
40[    0.036000] NET: Registered protocol family 16
41[    0.064000] bio: create slab <bio-0> at 0
42[    0.076000] Switching to clocksource MIPS
43[    0.088000] NET: Registered protocol family 2
44[    0.092000] TCP established hash table entries: 512 (order: 0, 4096 bytes)
45[    0.092000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)
46[    0.092000] TCP: Hash tables configured (established 512 bind 512)
47[    0.092000] TCP: reno registered
48[    0.092000] UDP hash table entries: 256 (order: 0, 4096 bytes)
49[    0.092000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
50[    0.092000] NET: Registered protocol family 1
51[    0.092000] PCI: CLS 0 bytes, default 32
52[    0.096000] bcma: bus0: Core 1 found: IEEE 802.11 (manuf 0x4BF, id 0x812, rev 0x1C, class 0x0)
53[    0.096000] bcma: bus0: Core 2 found: GBit MAC (manuf 0x4BF, id 0x82D, rev 0x03, class 0x0)
54[    0.096000] bcma: bus0: Core 4 found: SDR/DDR1 Memory Controller (manuf 0x4BF, id 0x835, rev 0x02, class 0x0)
55[    0.100000] can not parse nvram name sb/1/rxpo2g(null) with value 0xff got -34
56[    0.100000] can not parse nvram name sb/1/ag3(null) with value 0xff got -34
57[    0.132000] bcma: bus0: Using SPROM revision 8 provided by platform.
58[    0.132000] bcma: bus0: PMU resource config unknown or not needed for device 0xD144
59[    0.132000] bcma: bus0: Workarounds unknown or not needed for device 0xD144
60[    0.132000] bcma: bus0: Initializing MIPS core...
61[    0.132000] bcma: bus0: set_irq: core 0x0812, irq 3 => 3
62[    0.132000] bcma: bus0: set_irq: core 0x082d, irq 4 => 4
63[    0.132000] bcma: bus0: set_irq: core 0x0800, irq 2 => 2
64[    0.132000] bcma: bus0: IRQ reconfiguration done
65[    0.132000] bcma: core 0x0800, irq : 2(S)* 3  4  5  6  D  I
66[    0.132000] bcma: core 0x082c, irq : 2(S)  3  4  5  6  D  I*
67[    0.132000] bcma: core 0x0812, irq : 2(S)  3* 4  5  6  D  I
68[    0.132000] bcma: core 0x082d, irq : 2(S)  3  4* 5  6  D  I
69[    0.132000] bcma: core 0x0835, irq : 2(S)  3  4  5  6  D* I
70[    0.140000] bcma: bus0: Bus registered
71[    0.144000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
72[    0.144000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
73[    0.144000] msgmni has been set to 56
74[    0.144000] io scheduler noop registered
75[    0.144000] io scheduler deadline registered (default)
76[    0.148000] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
77[    0.184000] serial8250.0: ttyS0 at MMIO 0xb8000300 (irq = 2) is a U6_16550A
78[    0.512000] console [ttyS0] enabled
79[    0.608000] 6 bcm47xxpart partitions found on MTD device bcm47xxsflash
80[    0.612000] Creating 6 MTD partitions on "bcm47xxsflash":
81[    0.620000] 0x000000000000-0x000000020000 : "boot"
82[    0.628000] 0x000000020000-0x0000007f0000 : "linux"
83[    0.636000] 0x00000002001c-0x000000020960 : "loader"
84[    0.648000] 0x000000020960-0x00000012dc00 : "kernel"
85[    0.652000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
86[    0.672000] 0x00000012dc00-0x0000007f0000 : "rootfs"
87[    0.676000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
88[    0.692000] mtd: partition "rootfs" set to be root filesystem
89[    0.700000] mtd: partition "rootfs_data" created automatically, ofs=0x300000, len=0x4f0000
90[    0.708000] 0x000000300000-0x0000007f0000 : "rootfs_data"
91[    0.716000] 0x0000007f0000-0x000000800000 : "nvram"
92[    0.732000] bcm47xx-wdt bcm47xx-wdt.0: BCM47xx Watchdog Timer enabled (30 seconds)
93[    0.740000] GPIO_WDT: failed to register misc device
94[    0.748000] TCP: cubic registered
95[    0.752000] NET: Registered protocol family 17
96[    0.756000] Bridge firewalling registered
97[    0.760000] 8021q: 802.1Q VLAN Support v1.8
98[    0.780000] VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
99[    0.788000] Freeing unused kernel memory: 212K (8030b000 - 80340000)
100[    4.880000] pps_core: LinuxPPS API ver. 1 registered
101[    4.888000] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
102[    4.900000] PTP clock support registered
103[    4.916000] bgmac bcma0:1: Found PHY addr: 30 (NOREGS)
104[    4.932000] bgmac bcma0:1: Support for Roboswitch not implemented
105[    4.940000] libphy: bgmac mii bus: probed
106[    4.952000] b53_common: found switch: BCM5325, rev 4
107[    4.960000] (unregistered net_device): attached PHY driver [Broadcom B53 (2)] (mii_bus:phy_addr=bgmac-0-0:1e)
108[    4.972000] bgmac: Broadcom 47xx GBit MAC driver loaded
109[    5.012000] diag: unknown board found, try legacy detect
110[    5.016000] diag: please open a ticket at https://dev.openwrt.org and attach the complete nvram
111[    5.028000] diag: Router model not detected.
112[    5.040000] diag: unknown board found, try legacy detect
113[    5.048000] diag: please open a ticket at https://dev.openwrt.org and attach the complete nvram
114[    5.056000] diag: Router model not detected.
115[    8.896000] jffs2: notice: (213) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (0 unchecked, 0 orphan) and 8 of xref (0 dead, 2 orphan) found.
116[   11.532000] NET: Registered protocol family 10
117[   11.556000] nf_conntrack version 0.5.0 (454 buckets, 1816 max)
118[   11.576000] ip6_tables: (C) 2000-2006 Netfilter Core Team
119[   11.628000] diag: unknown board found, try legacy detect
120[   11.632000] diag: please open a ticket at https://dev.openwrt.org and attach the complete nvram
121[   11.644000] diag: Router model not detected.
122[   11.652000] Loading modules backported from Linux version master-2013-06-27-0-gdcfa6d5
123[   11.660000] Backport generated by backports.git backports-20130617-4-ge3220f5
124[   11.684000] diag: unknown board found, try legacy detect
125[   11.688000] diag: please open a ticket at https://dev.openwrt.org and attach the complete nvram
126[   11.696000] diag: Router model not detected.
127[   11.708000] ip_tables: (C) 2000-2006 Netfilter Core Team
128[   11.804000] xt_time: kernel timezone is -0000
129[   11.864000] diag: unknown board found, try legacy detect
130[   11.868000] diag: please open a ticket at https://dev.openwrt.org and attach the complete nvram
131[   11.876000] diag: Router model not detected.
132[   11.896000] cfg80211: Calling CRDA to update world regulatory domain
133[   11.908000] cfg80211: World regulatory domain updated:
134[   11.912000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
135[   11.920000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
136[   11.928000] cfg80211:   (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
137[   11.936000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
138[   11.944000] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
139[   11.952000] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
140[   12.092000] PPP generic driver version 2.4.2
141[   12.108000] NET: Registered protocol family 24
142[   12.156000] Broadcom 43xx driver loaded [ Features: PNL ]
143[   12.176000] Broadcom 43xx-legacy driver loaded [ Features: PLD ]
144[   12.196000] diag: unknown board found, try legacy detect
145[   12.200000] diag: please open a ticket at https://dev.openwrt.org and attach the complete nvram
146[   12.208000] diag: Router model not detected.
147[   12.236000] diag: unknown board found, try legacy detect
148[   12.244000] diag: please open a ticket at https://dev.openwrt.org and attach the complete nvram
149[   12.252000] diag: Router model not detected.
150[   20.328000] device eth0.0 entered promiscuous mode
151[   20.332000] device eth0 entered promiscuous mode
152[   20.348000] br-lan: port 1(eth0.0) entered forwarding state
153[   20.352000] br-lan: port 1(eth0.0) entered forwarding state
154[   22.356000] br-lan: port 1(eth0.0) entered forwarding state