Ticket #13096: dmesg.txt

File dmesg.txt, 9.7 KB (added by stefan@…, 5 years ago)
Line 
1[    0.000000] Linux version 3.3.8 (openwrt-om2p-aa@dorfl) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #4 Thu Feb 28 13:06:59 CET 2013
2[    0.000000] MyLoader: sysp=f5feff7f, boardp=f8d73f7b, parts=04084420
3[    0.000000] bootconsole [early0] enabled
4[    0.000000] CPU revision is: 00019374 (MIPS 24Kc)
5[    0.000000] SoC: Atheros AR7240 rev 2
6[    0.000000] Clocks: CPU:400.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:5.000MHz
7[    0.000000] Determined physical RAM map:
8[    0.000000]  memory: 04000000 @ 00000000 (usable)
9[    0.000000] User-defined physical RAM map:
10[    0.000000]  memory: 04000000 @ 00000000 (usable)
11[    0.000000] Initrd not found or empty - disabling initrd
12[    0.000000] Zone PFN ranges:
13[    0.000000]   Normal   0x00000000 -> 0x00004000
14[    0.000000] Movable zone start PFN for each node
15[    0.000000] Early memory PFN ranges
16[    0.000000]     0: 0x00000000 -> 0x00004000
17[    0.000000] On node 0 totalpages: 16384
18[    0.000000] free_area_init_node: node 0, pgdat 802ce170, node_mem_map 81000000
19[    0.000000]   Normal zone: 128 pages used for memmap
20[    0.000000]   Normal zone: 0 pages reserved
21[    0.000000]   Normal zone: 16256 pages, LIFO batch:3
22[    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
23[    0.000000] pcpu-alloc: [0] 0
24[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
25[    0.000000] Kernel command line:  console=ttyS0,115200 root=31:04 rootfstype=squashfs,jffs2 init=/etc/preinit mtdparts=ar7240-nor0:256k(u-boot),256k(u-boot-env),1280k(custom),1024k(kernel),6144k(rootfs),7168k(inactive),256k(ART) board=OM2P mem=64M rootfstype=squashfs,jffs2 noinitrd
26[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
27[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
28[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
29[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
30[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
31[    0.000000] Writing ErrCtl register=00000000
32[    0.000000] Readback ErrCtl register=00000000
33[    0.000000] Memory: 61636k/65536k available (2086k kernel code, 3900k reserved, 403k data, 208k init, 0k highmem)
34[    0.000000] SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
35[    0.000000] NR_IRQS:51
36[    0.000000] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104)
37[    0.080000] pid_max: default: 32768 minimum: 301
38[    0.080000] Mount-cache hash table entries: 512
39[    0.090000] NET: Registered protocol family 16
40[    0.090000] gpiochip_add: registered GPIOs 0 to 17 on device: ath79
41[    0.100000] MIPS: machine is OpenMesh OM2P
42[    0.500000] registering PCI controller with io_map_base unset
43[    0.510000] bio: create slab <bio-0> at 0
44[    0.520000] PCI host bridge to bus 0000:00
45[    0.520000] pci_bus 0000:00: root bus resource [mem 0x10000000-0x13ffffff]
46[    0.530000] pci_bus 0000:00: root bus resource [io  0x0000]
47[    0.530000] pci 0000:00:00.0: [168c:002b] type 0 class 0x000280
48[    0.530000] pci 0000:00:00.0: fixup device configuration
49[    0.540000] pci 0000:00:00.0: reg 10: [mem 0x00000000-0x0000ffff 64bit]
50[    0.540000] pci 0000:00:00.0: supports D1
51[    0.540000] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
52[    0.540000] pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x1000ffff 64bit]
53[    0.540000] pci 0000:00:00.0: using irq 40 for pin 1
54[    0.550000] Switching to clocksource MIPS
55[    0.550000] NET: Registered protocol family 2
56[    0.560000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
57[    0.560000] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
58[    0.570000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
59[    0.570000] TCP: Hash tables configured (established 2048 bind 2048)
60[    0.580000] TCP reno registered
61[    0.580000] UDP hash table entries: 256 (order: 0, 4096 bytes)
62[    0.590000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
63[    0.600000] NET: Registered protocol family 1
64[    0.600000] PCI: CLS 0 bytes, default 32
65[    0.620000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
66[    0.620000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
67[    0.640000] msgmni has been set to 120
68[    0.640000] io scheduler noop registered
69[    0.640000] io scheduler deadline registered (default)
70[    0.650000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
71[    0.680000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A
72[    0.680000] console [ttyS0] enabled, bootconsole disabled
73[    0.700000] m25p80 spi0.0: s25sl12800 (16384 Kbytes)
74[    0.700000] 7 cmdlinepart partitions found on MTD device ar7240-nor0
75[    0.710000] Creating 7 MTD partitions on "ar7240-nor0":
76[    0.710000] 0x000000000000-0x000000040000 : "u-boot"
77[    0.720000] 0x000000040000-0x000000080000 : "u-boot-env"
78[    0.730000] 0x000000080000-0x0000001c0000 : "custom"
79[    0.730000] 0x0000001c0000-0x0000002c0000 : "kernel"
80[    0.740000] 0x0000002c0000-0x0000008c0000 : "rootfs"
81[    0.750000] mtd: partition "rootfs" set to be root filesystem
82[    0.750000] mtd: partition "rootfs_data" created automatically, ofs=580000, len=340000
83[    0.760000] 0x000000580000-0x0000008c0000 : "rootfs_data"
84[    0.770000] 0x0000008c0000-0x000000fc0000 : "inactive"
85[    0.780000] 0x000000fc0000-0x000001000000 : "ART"
86[    0.810000] ag71xx_mdio: probed
87[    0.810000] eth0: Atheros AG71xx at 0xb9000000, irq 4
88[    1.390000] ag71xx ag71xx.0: eth0: connected to PHY at ag71xx-mdio.0:04 [uid=004dd041, driver=Generic PHY]
89[    1.400000] eth1: Atheros AG71xx at 0xba000000, irq 5
90[    1.970000] eth1: Found an AR7240/AR9330 built-in switch
91[    3.000000] TCP cubic registered
92[    3.000000] NET: Registered protocol family 17
93[    3.000000] 8021q: 802.1Q VLAN Support v1.8
94[    3.010000] VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
95[    3.020000] Freeing unused kernel memory: 208k freed
96[    5.090000] Registered led device: om2p:blue:power
97[    5.090000] Registered led device: om2p:red:wifi
98[    5.090000] Registered led device: om2p:yellow:wifi
99[    5.090000] Registered led device: om2p:green:wifi
100[    5.090000] Registered led device: om2p:blue:lan
101[    5.100000] Registered led device: om2p:blue:wan
102[    7.390000] eth0: link up (100Mbps/Full duplex)
103[    8.410000] eth0: link down
104[   10.120000] Compat-drivers backport release: compat-drivers-2012-09-04-2-gddac993
105[   10.120000] Backport based on wireless-testing.git master-2012-09-07
106[   10.130000] compat.git: wireless-testing.git
107[   10.160000] cfg80211: Calling CRDA to update world regulatory domain
108[   10.170000] cfg80211: World regulatory domain updated:
109[   10.170000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
110[   10.180000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
111[   10.190000] cfg80211:   (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
112[   10.190000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
113[   10.200000] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
114[   10.210000] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
115[   10.550000] usbcore: registered new interface driver usbfs
116[   10.560000] usbcore: registered new interface driver hub
117[   10.560000] usbcore: registered new device driver usb
118[   11.040000] PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
119[   11.050000] ath: EEPROM regdomain: 0x0
120[   11.050000] ath: EEPROM indicates default country code should be used
121[   11.050000] ath: doing EEPROM country->regdmn map search
122[   11.050000] ath: country maps to regdmn code: 0x3a
123[   11.050000] ath: Country alpha2 being used: US
124[   11.050000] ath: Regpair used: 0x3a
125[   11.050000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
126[   11.050000] Registered led device: ath9k-phy0
127[   11.050000] ieee80211 phy0: Atheros AR9285 Rev:2 mem=0xb0000000, irq=40
128[   11.060000] cfg80211: Calling CRDA for country: US
129[   11.070000] cfg80211: Regulatory domain changed to country: US
130[   11.070000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
131[   11.080000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
132[   11.090000] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)
133[   11.100000] cfg80211:   (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
134[   11.110000] cfg80211:   (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
135[   11.110000] cfg80211:   (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
136[   11.120000] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)
137[   11.180000] PPP generic driver version 2.4.2
138[   11.330000] ip_tables: (C) 2000-2006 Netfilter Core Team
139[   11.440000] NET: Registered protocol family 24
140[   11.460000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
141[   11.480000] nf_conntrack version 0.5.0 (966 buckets, 3864 max)
142[   11.710000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
143[   16.150000] device eth0 entered promiscuous mode
144[   17.190000] device eth1 entered promiscuous mode
145[   18.400000] eth0: link up (100Mbps/Full duplex)
146[   18.400000] br-lan: port 1(eth0) entered forwarding state
147[   18.410000] br-lan: port 1(eth0) entered forwarding state
148[   20.410000] br-lan: port 1(eth0) entered forwarding state
149[   31.140000] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
150[   31.140000] jffs2_build_filesystem(): unlocking the mtd device... done.
151[   31.150000] jffs2_build_filesystem(): erasing all blocks after the end marker... done.
152[   48.610000] JFFS2 notice: (1148) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.