Ticket #12838: dmesg

File dmesg, 11.9 KB (added by Noel Maersk <veox@…>, 5 years ago)

dmesg output from running system

Line 
1[    0.000000] Linux version 3.6.11 (veox@localhost) (gcc version 4.6.4 20121210 (prerelease) (Linaro GCC 4.6-2012.12) ) #11 Fri Jan 18 12:51:46 UTC 2013
2[    0.000000] CPU revision is: 00029029 (Broadcom BMIPS3300)
3[    0.000000] bcm47xx: using ssb bus
4[    0.000000] ssb: Found chip with id 0x5354, rev 0x03 and package 0x00
5[    0.000000] ssb: Core 0 found: ChipCommon (cc 0x800, rev 0x14, vendor 0x4243)
6[    0.000000] ssb: Core 1 found: Fast Ethernet (cc 0x806, rev 0x09, vendor 0x4243)
7[    0.000000] ssb: Core 2 found: MIPS 3302 (cc 0x816, rev 0x08, vendor 0x4243)
8[    0.000000] ssb: Core 3 found: USB 2.0 Host (cc 0x819, rev 0x02, vendor 0x4243)
9[    0.000000] ssb: Core 4 found: MEMC SDRAM (cc 0x80F, rev 0x04, vendor 0x4243)
10[    0.000000] ssb: Core 5 found: IEEE 802.11 (cc 0x812, rev 0x0D, vendor 0x4243)
11[    0.000000] ssb: Core 6 found: Roboswitch (cc 0x81C, rev 0x02, vendor 0x4243)
12[    0.000000] ssb: chipcommon status is 0x0
13[    0.000000] ssb: Found rev 0 PMU (capabilities 0x04A63400)
14[    0.000000] Couldn't find supported flash memory
15[    0.000000] ssb: Initializing MIPS core...
16[    0.000000] ssb: set_irq: core 0x0806, irq 4 => 4
17[    0.000000] ssb: set_irq: core 0x0816, irq 5 => 2
18[    0.000000] ssb: set_irq: core 0x0812, irq 2 => 5
19[    0.000000] ssb: after irq reconfiguration
20[    0.000000] ssb: core 0x0800, irq : 2(S)  3* 4  5  6  D  I
21[    0.000000] ssb: core 0x0806, irq : 2(S)  3  4* 5  6  D  I
22[    0.000000] ssb: core 0x0816, irq : 2(S)* 3  4  5  6  D  I
23[    0.000000] ssb: core 0x0819, irq : 2(S)  3  4  5  6* D  I
24[    0.000000] ssb: core 0x080f, irq : 2(S)  3  4  5  6  D  I*
25[    0.000000] ssb: core 0x0812, irq : 2(S)  3  4  5* 6  D  I
26[    0.000000] ssb: core 0x081c, irq : 2(S)  3  4  5  6  D  I*
27[    0.000000] gpiochip_add: registered GPIOs 0 to 15 on device: ssb_chipco_gpio
28[    0.000000] can not parse nvram name (null)boardnum(null) with value  got -22
29[    0.000000] can not parse nvram name (null)rxpo2g(null) with value 0xfff8 got -34
30[    0.000000] ssb: Sonics Silicon Backplane found at address 0x18000000
31[    0.000000] Serial init done.
32[    0.000000] Determined physical RAM map:
33[    0.000000]  memory: 02000000 @ 00000000 (usable)
34[    0.000000] Initrd not found or empty - disabling initrd
35[    0.000000] Zone ranges:
36[    0.000000]   Normal   [mem 0x00000000-0x01ffffff]
37[    0.000000] Movable zone start for each node
38[    0.000000] Early memory node ranges
39[    0.000000]   node   0: [mem 0x00000000-0x01ffffff]
40[    0.000000] On node 0 totalpages: 8192
41[    0.000000] free_area_init_node: node 0, pgdat 802b4970, node_mem_map 81000000
42[    0.000000]   Normal zone: 64 pages used for memmap
43[    0.000000]   Normal zone: 0 pages reserved
44[    0.000000]   Normal zone: 8128 pages, LIFO batch:0
45[    0.000000] Primary instruction cache 16kB, VIPT, 4-way, linesize 16 bytes.
46[    0.000000] Primary data cache 16kB, 2-way, VIPT, cache aliases, linesize 16 bytes
47[    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
48[    0.000000] pcpu-alloc: [0] 0
49[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 8128
50[    0.000000] Kernel command line:  root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
51[    0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
52[    0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
53[    0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
54[    0.000000] __ex_table already sorted, skipping sort
55[    0.000000] Memory: 29252k/32768k available (2406k kernel code, 3516k reserved, 361k data, 164k init, 0k highmem)
56[    0.000000] NR_IRQS:128
57[    0.000000] console [ttyS0] enabled
58[    0.144000] Calibrating delay loop... 237.82 BogoMIPS (lpj=475648)
59[    0.180000] pid_max: default: 32768 minimum: 301
60[    0.184000] Mount-cache hash table entries: 512
61[    0.192000] NET: Registered protocol family 16
62[    0.228000] bio: create slab <bio-0> at 0
63[    0.240000] Switching to clocksource MIPS
64[    0.268000] NET: Registered protocol family 2
65[    0.276000] TCP established hash table entries: 1024 (order: 1, 8192 bytes)
66[    0.284000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
67[    0.288000] TCP: Hash tables configured (established 1024 bind 1024)
68[    0.296000] TCP: reno registered
69[    0.300000] UDP hash table entries: 256 (order: 0, 4096 bytes)
70[    0.308000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
71[    0.312000] NET: Registered protocol family 1
72[    0.320000] PCI: CLS 0 bytes, default 16
73[    0.328000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
74[    0.332000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
75[    0.344000] msgmni has been set to 57
76[    0.348000] io scheduler noop registered
77[    0.352000] io scheduler deadline registered (default)
78[    0.360000] Serial: 8250/16550 driver, 2 ports, IRQ sharing enabled
79[    0.388000] serial8250: ttyS0 at MMIO 0xb8000300 (irq = 3) is a U6_16550A
80[    0.416000] serial8250: ttyS1 at MMIO 0xb8000400 (irq = 3) is a U6_16550A
81[    0.444000] serial8250.0: ttyS0 at MMIO 0xb8000300 (irq = 3) is a U6_16550A
82[    0.476000] serial8250.0: ttyS1 at MMIO 0xb8000400 (irq = 3) is a U6_16550A
83[    0.488000] bcm47xx_pflash: flash init: 0x1c000000 0x02000000
84[    0.496000] Physically mapped flash: Found 1 x16 devices at 0x0 in 8-bit bank. Manufacturer ID 0x000001 Chip ID 0x001a01
85[    0.508000] Physically mapped flash: Found an alias at 0x400000 for the chip at 0x0
86[    0.508000] Physically mapped flash: Found an alias at 0x800000 for the chip at 0x0
87[    0.508000] Physically mapped flash: Found an alias at 0xc00000 for the chip at 0x0
88[    0.508000] Physically mapped flash: Found an alias at 0x1000000 for the chip at 0x0
89[    0.508000] Physically mapped flash: Found an alias at 0x1400000 for the chip at 0x0
90[    0.508000] Physically mapped flash: Found an alias at 0x1800000 for the chip at 0x0
91[    0.508000] Physically mapped flash: Found an alias at 0x1c00000 for the chip at 0x0
92[    0.508000] Amd/Fujitsu Extended Query Table at 0x0040
93[    0.512000]   Amd/Fujitsu Extended Query version 1.3.
94[    0.520000] Physically mapped flash: Swapping erase regions for top-boot CFI table.
95[    0.528000] number of CFI chips: 1
96[    0.528000] bcm47xx_pflash: Flash device: 0x2000000 at 0x1fc00000
97[    0.536000] bcm47xx_part: bootloader size: 262144
98[    0.540000] bcm47xx_part: Looking for dual image
99[    0.548000] bcm47xx_part: TRX offset : 0
100[    0.972000] bcm47xx_part: Updating TRX offsets and length:
101[    0.976000] bcm47xx_part: old trx = [0x0000001c, 0x00000960, 0x000e4000], len=0x00331000 crc32=0x7068c823
102[    0.988000] bcm47xx_part: new trx = [0x0000001c, 0x00000960, 0x000e4000], len=0x000e4000 crc32=0x49a20673
103[    1.816000] bcm47xx_part: Done
104[    1.820000] 4 bcm47xx partitions found on MTD device Physically mapped flash
105[    1.828000] Creating 4 MTD partitions on "Physically mapped flash":
106[    1.836000] 0x000000000000-0x000000040000 : "cfe"
107[    1.844000] 0x000000040000-0x0000003f0000 : "linux"
108[    1.856000] 0x000000124000-0x0000003f0000 : "rootfs"
109[    1.864000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
110[    1.880000] mtd: partition "rootfs" set to be root filesystem
111[    1.888000] mtd: partition "rootfs_data" created automatically, ofs=330000, len=C0000
112[    1.896000] 0x000000330000-0x0000003f0000 : "rootfs_data"
113[    1.908000] 0x0000003f0000-0x000000400000 : "nvram"
114[    1.924000] bcm47xx-wdt bcm47xx-wdt.0: BCM47xx Watchdog Timer enabled (30 seconds, Software Timer)
115[    1.936000] TCP: cubic registered
116[    1.940000] NET: Registered protocol family 17
117[    1.944000] 8021q: 802.1Q VLAN Support v1.8
118[    1.968000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
119[    1.976000] Freeing unused kernel memory: 164k freed
120[    5.804000] diag: Detected 'D-Link DIR-320'
121[    6.012000] b44: Broadcom 44xx/47xx 10/100 PCI ethernet driver version 2.0
122[    6.044000] b44 ssb0:0: eth0: Broadcom 44xx/47xx 10/100 PCI ethernet driver 00:90:4c:c0:00:00
123[    6.176000] b44 ssb0:0: eth0: Link is up at 100 Mbps, full duplex
124[    6.180000] b44 ssb0:0: eth0: Flow control is off for TX and off for RX
125[    6.512000] roboswitch: Probing device 'eth0'
126[    6.520000] roboswitch: found a 5325! It's a 5350. at eth0
127[   22.988000] b44 ssb0:0: eth0: powering down PHY
128[   26.964000] Compat-drivers backport release: compat-drivers-2013-01-08-3
129[   26.972000] Backport based on wireless-testing.git master-2013-01-07
130[   26.980000] compat.git: wireless-testing.git
131[   27.056000] cfg80211: Calling CRDA to update world regulatory domain
132[   27.060000] cfg80211: World regulatory domain updated:
133[   27.068000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
134[   27.076000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
135[   27.084000] cfg80211:   (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
136[   27.092000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
137[   27.100000] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
138[   27.108000] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
139[   27.592000] SCSI subsystem initialized
140[   28.032000] usbcore: registered new interface driver usbfs
141[   28.036000] usbcore: registered new interface driver hub
142[   28.048000] usbcore: registered new device driver usb
143[   28.960000] b43-phy0: Broadcom 5354 WLAN found (core revision 13)
144[   28.988000] b43-phy0: Found PHY: Analog 6, Type 5 (LP), Revision 0
145[   29.016000] Broadcom 43xx driver loaded [ Features: PNL ]
146[   30.104000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
147[   30.400000] tun: Universal TUN/TAP device driver, 1.6
148[   30.404000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
149[   31.028000] ip_tables: (C) 2000-2006 Netfilter Core Team
150[   31.620000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
151[   31.628000] ehci-platform ehci-platform.0: Generic Platform EHCI Controller
152[   31.636000] ehci-platform ehci-platform.0: new USB bus registered, assigned bus number 1
153[   31.644000] ehci-platform ehci-platform.0: irq 6, io mem 0x18003800
154[   31.664000] ehci-platform ehci-platform.0: USB 2.0 started, EHCI 1.00
155[   31.672000] hub 1-0:1.0: USB hub found
156[   31.676000] hub 1-0:1.0: 2 ports detected
157[   31.924000] nf_conntrack version 0.5.0 (459 buckets, 1836 max)
158[   33.164000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
159[   33.172000] ohci-platform ohci-platform.0: Generic Platform OHCI Controller
160[   33.180000] ohci-platform ohci-platform.0: new USB bus registered, assigned bus number 2
161[   33.188000] ohci-platform ohci-platform.0: irq 6, io mem 0x18003000
162[   33.252000] hub 2-0:1.0: USB hub found
163[   33.256000] hub 2-0:1.0: 2 ports detected
164[   33.508000] uhci_hcd: USB Universal Host Controller Interface driver
165[   33.572000] Initializing USB Mass Storage driver...
166[   33.580000] usbcore: registered new interface driver usb-storage
167[   33.584000] USB Mass Storage support registered.
168[   38.780000] b44 ssb0:0: eth0: Link is up at 100 Mbps, full duplex
169[   38.788000] b44 ssb0:0: eth0: Flow control is off for TX and off for RX
170[   41.032000] b44 ssb0:0: eth0: powering down PHY
171[   41.064000] b44 ssb0:0: eth0: Link is up at 100 Mbps, full duplex
172[   41.072000] b44 ssb0:0: eth0: Flow control is off for TX and off for RX
173[   41.096000] device eth0.0 entered promiscuous mode
174[   41.100000] device eth0 entered promiscuous mode
175[   41.112000] br-lan: port 1(eth0.0) entered forwarding state
176[   41.116000] br-lan: port 1(eth0.0) entered forwarding state
177[   43.120000] br-lan: port 1(eth0.0) entered forwarding state
178[   73.792000] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
179[   73.808000] jffs2_build_filesystem(): unlocking the mtd device... done.
180[   73.812000] jffs2_build_filesystem(): erasing all blocks after the end marker... done.
181[   80.452000] jffs2: notice: (1119) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.