Ticket #12249: KernelLog.txt

File KernelLog.txt, 10.8 KB (added by h.sehgal@…, 5 years ago)

Kernel Log

Line 
1[    0.000000] Linux version 3.3.8 (blogic@Debian-60-squeeze-64-minimal) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #3 Mon Sep 3 16:16:20 UTC 2012
2[    0.000000] CPU revision is: 00029008 (Broadcom BMIPS3300)
3[    0.000000] bcm47xx: using ssb bus
4[    0.000000] ssb: Found chip with id 0x5352, rev 0x00 and package 0x02
5[    0.000000] ssb: Core 0 found: ChipCommon (cc 0x800, rev 0x0E, vendor 0x4243)
6[    0.000000] ssb: Core 1 found: Fast Ethernet (cc 0x806, rev 0x09, vendor 0x4243)
7[    0.000000] ssb: Core 2 found: MIPS 3302 (cc 0x816, rev 0x06, vendor 0x4243)
8[    0.000000] ssb: Core 3 found: USB 1.1 Host (cc 0x817, rev 0x02, vendor 0x4243)
9[    0.000000] ssb: Core 4 found: MEMC SDRAM (cc 0x80F, rev 0x01, vendor 0x4243)
10[    0.000000] ssb: Core 5 found: IEEE 802.11 (cc 0x812, rev 0x09, vendor 0x4243)
11[    0.000000] ssb: Core 6 found: Roboswitch (cc 0x81C, rev 0x02, vendor 0x4243)
12[    0.000000] ssb: chipcommon status is 0x0
13[    0.000000] ssb: Initializing MIPS core...
14[    0.000000] ssb: set_irq: core 0x0806, irq 4 => 4
15[    0.000000] ssb: set_irq: core 0x0816, irq 5 => 2
16[    0.000000] ssb: set_irq: core 0x0812, irq 2 => 5
17[    0.000000] ssb: after irq reconfiguration
18[    0.000000] ssb: core 0x0800, irq : 2(S)  3* 4  5  6  D  I
19[    0.000000] ssb: core 0x0806, irq : 2(S)  3  4* 5  6  D  I
20[    0.000000] ssb: core 0x0816, irq : 2(S)* 3  4  5  6  D  I
21[    0.000000] ssb: core 0x0817, irq : 2(S)  3  4  5  6* D  I
22[    0.000000] ssb: core 0x080f, irq : 2(S)  3  4  5  6  D  I*
23[    0.000000] ssb: core 0x0812, irq : 2(S)  3  4  5* 6  D  I
24[    0.000000] ssb: core 0x081c, irq : 2(S)  3  4  5  6  D  I*
25[    0.000000] found parallel flash.
26[    0.000000] ssb: Sonics Silicon Backplane found at address 0x18000000
27[    0.000000] Serial init done.
28[    0.000000] gpiochip_add: registered GPIOs 0 to 15 on device: bcm47xx
29[    0.000000] Determined physical RAM map:
30[    0.000000]  memory: 02000000 @ 00000000 (usable)
31[    0.000000] Initrd not found or empty - disabling initrd
32[    0.000000] Zone PFN ranges:
33[    0.000000]   Normal   0x00000000 -> 0x00002000
34[    0.000000] Movable zone start PFN for each node
35[    0.000000] Early memory PFN ranges
36[    0.000000]     0: 0x00000000 -> 0x00002000
37[    0.000000] On node 0 totalpages: 8192
38[    0.000000] free_area_init_node: node 0, pgdat 802d6530, node_mem_map 81000000
39[    0.000000]   Normal zone: 64 pages used for memmap
40[    0.000000]   Normal zone: 0 pages reserved
41[    0.000000]   Normal zone: 8128 pages, LIFO batch:0
42[    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
43[    0.000000] pcpu-alloc: [0] 0
44[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 8128
45[    0.000000] Kernel command line:  root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
46[    0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
47[    0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
48[    0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
49[    0.000000] Primary instruction cache 16kB, VIPT, 2-way, linesize 16 bytes.
50[    0.000000] Primary data cache 8kB, 2-way, VIPT, no aliases, linesize 16 bytes
51[    0.000000] Memory: 29228k/32768k available (2521k kernel code, 3540k reserved, 381k data, 168k init, 0k highmem)
52[    0.000000] NR_IRQS:128
53[    0.000000] console [ttyS0] enabled
54[    0.004000] Calibrating delay loop... 198.65 BogoMIPS (lpj=397312)
55[    0.040000] pid_max: default: 32768 minimum: 301
56[    0.044000] Mount-cache hash table entries: 512
57[    0.056000] NET: Registered protocol family 16
58[    0.108000] bio: create slab <bio-0> at 0
59[    0.124000] Switching to clocksource MIPS
60[    0.160000] NET: Registered protocol family 2
61[    0.164000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
62[    0.172000] TCP established hash table entries: 1024 (order: 1, 8192 bytes)
63[    0.180000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
64[    0.188000] TCP: Hash tables configured (established 1024 bind 1024)
65[    0.196000] TCP reno registered
66[    0.196000] UDP hash table entries: 256 (order: 0, 4096 bytes)
67[    0.204000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
68[    0.212000] NET: Registered protocol family 1
69[    0.216000] PCI: CLS 0 bytes, default 16
70[    0.228000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
71[    0.236000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
72[    0.248000] msgmni has been set to 57
73[    0.252000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
74[    0.260000] io scheduler noop registered
75[    0.264000] io scheduler deadline registered (default)
76[    0.272000] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
77[    0.300000] serial8250: ttyS0 at MMIO 0xb8000300 (irq = 3) is a U6_16550A
78[    0.328000] serial8250: ttyS1 at MMIO 0xb8000400 (irq = 3) is a U6_16550A
79[    0.380000] serial8250.0: ttyS0 at MMIO 0xb8000300 (irq = 3) is a U6_16550A
80[    0.412000] serial8250.0: ttyS1 at MMIO 0xb8000400 (irq = 3) is a U6_16550A
81[    0.428000] bcm47xx_pflash: flash init: 0x1c000000 0x02000000
82[    0.436000] Physically mapped flash: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x000089 Chip ID 0x000017
83[    0.444000] Physically mapped flash: Found an alias at 0x800000 for the chip at 0x0
84[    0.448000] Physically mapped flash: Found an alias at 0x1000000 for the chip at 0x0
85[    0.448000] Physically mapped flash: Found an alias at 0x1800000 for the chip at 0x0
86[    0.448000] Intel/Sharp Extended Query Table at 0x0031
87[    0.452000] Intel/Sharp Extended Query Table at 0x0031
88[    0.456000] Using buffer write method
89[    0.460000] cfi_cmdset_0001: Erase suspend on write enabled
90[    0.468000] erase region 0: offset=0x0,size=0x20000,blocks=64
91[    0.468000] bcm47xx_pflash: Flash device: 0x2000000 at 0x1fc00000
92[    0.472000] bcm47xx_part: bootloader size: 262144
93[    0.480000] bcm47xx_part: Looking for dual image
94[    0.484000] bcm47xx_part: TRX offset : 0
95[    0.488000] 4 bcm47xx partitions found on MTD device Physically mapped flash
96[    0.496000] Creating 4 MTD partitions on "Physically mapped flash":
97[    0.500000] 0x000000000000-0x000000040000 : "cfe"
98[    0.516000] 0x000000040000-0x0000007e0000 : "linux"
99[    0.528000] 0x000000132400-0x0000007e0000 : "rootfs"
100[    0.532000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
101[    0.552000] mtd: partition "rootfs" set to be root filesystem
102[    0.560000] mtd: partition "rootfs_data" created automatically, ofs=300000, len=4E0000
103[    0.568000] 0x000000300000-0x0000007e0000 : "rootfs_data"
104[    0.580000] 0x0000007e0000-0x000000800000 : "nvram"
105[    0.596000] bcm47xx_sflash: error registering platform driver: -19
106[    0.608000] bcm47xx_nflash: error registering platform driver: -19
107[    0.616000] b44: Broadcom 44xx/47xx 10/100 PCI ethernet driver version 2.0
108[    0.628000] b44 ssb0:0: eth0: Broadcom 44xx/47xx 10/100 PCI ethernet driver 00:1c:10:3a:b4:75
109[    0.640000] BCM47xx Watchdog Timer enabled (30 seconds, nowayout)
110[    0.648000] TCP cubic registered
111[    0.652000] NET: Registered protocol family 17
112[    0.656000] 8021q: 802.1Q VLAN Support v1.8
113[    0.676000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
114[    0.688000] Freeing unused kernel memory: 168k freed
115[    5.220000] diag: Detected 'Linksys WRT54G/GS/GL'
116[    5.292000] b44 ssb0:0: eth0: Link is up at 100 Mbps, full duplex
117[    5.300000] b44 ssb0:0: eth0: Flow control is off for TX and off for RX
118[    6.488000] roboswitch: Probing device eth0: found a 5325! It's a 5350.
119[   14.268000] JFFS2 notice: (329) jffs2_build_xattr_subsystem: complete building xattr subsystem, 19 of xdatum (0 unchecked, 18 orphan) and 23 of xref (0 dead, 20 orphan) found.
120[   19.708000] b44 ssb0:0: eth0: powering down PHY
121[   25.424000] Compat-wireless backport release: compat-wireless-2012-07-13
122[   25.432000] Backport based on wireless-testing.git master-2012-07-16
123[   25.440000] compat.git: wireless-testing.git
124[   25.528000] cfg80211: Calling CRDA to update world regulatory domain
125[   25.532000] cfg80211: World regulatory domain updated:
126[   25.540000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
127[   25.548000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
128[   25.556000] cfg80211:   (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
129[   25.564000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
130[   25.572000] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
131[   25.580000] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
132[   26.816000] b43-phy0: Broadcom 5352 WLAN found (core revision 9)
133[   26.872000] Broadcom 43xx driver loaded [ Features: PNL ]
134[   26.984000] Broadcom 43xx-legacy driver loaded [ Features: PLID ]
135[   27.584000] PPP generic driver version 2.4.2
136[   28.216000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
137[   28.360000] ip_tables: (C) 2000-2006 Netfilter Core Team
138[   28.732000] NET: Registered protocol family 24
139[   28.796000] nf_conntrack version 0.5.0 (459 buckets, 1836 max)
140[   33.912000] b44 ssb0:0: eth0: Link is up at 100 Mbps, full duplex
141[   33.916000] b44 ssb0:0: eth0: Flow control is off for TX and off for RX
142[   38.016000] b44 ssb0:0: eth0: powering down PHY
143[   38.060000] b44 ssb0:0: eth0: Link is up at 100 Mbps, full duplex
144[   38.068000] b44 ssb0:0: eth0: Flow control is off for TX and off for RX
145[   38.120000] device eth0.0 entered promiscuous mode
146[   38.124000] device eth0 entered promiscuous mode
147[   38.140000] br-lan: port 1(eth0.0) entered forwarding state
148[   38.144000] br-lan: port 1(eth0.0) entered forwarding state
149[   40.148000] br-lan: port 1(eth0.0) entered forwarding state
150[   40.208000] cfg80211: Calling CRDA for country: US
151[   40.216000] cfg80211: Regulatory domain changed to country: US
152[   40.220000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
153[   40.232000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
154[   40.240000] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)
155[   40.248000] cfg80211:   (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
156[   40.256000] cfg80211:   (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
157[   40.264000] cfg80211:   (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
158[   40.272000] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)
159[   46.184000] b43-phy0: Loading firmware version 666.2 (2011-02-23 01:15:07)
160[   46.356000] device wlan0 entered promiscuous mode
161[   46.512000] b43-phy0: Loading firmware version 666.2 (2011-02-23 01:15:07)
162[   48.488000] br-lan: port 2(wlan0) entered forwarding state
163[   48.496000] br-lan: port 2(wlan0) entered forwarding state
164[   50.500000] br-lan: port 2(wlan0) entered forwarding state